Summer Deluxe Stairway User manual

INSTRUCTION MANUAL
'HOX[H6WDLUZD\
6LPSOHWR6HFXUH:RRG*DWH
Please read the following instructions carefully.
Keep this instruction manual
and save for future reference.
Tools required: Wrench (included).
Phillips-head screwdriver (not included).
and drill (not included).
For technical support, contact us at 
or ZZZVXPPHULQIDQWFRPFRQWDFW
For use with children from 6 to 24 months.
Keep small parts away from children.
Adult assembly required.
Fits openings from 30" - 48" wide.
%
Thank you for purchasing the Deluxe Stairway Simple to Secure Wood Gate
from Summer Infant.This helpful gate allows you to create and maintain a secure
environment at the top of the stairs for your child (or pets).


0$,17(1$1&(
23(5$7,21
• Check all hardware to make sure the gate is securely in place.
• Do not use the gate if any components are damaged or missing.
• Wipe surface with a damp cloth or sponge, using mild detergent and warm water
to clean. Towel dry.
7R2SHQ Simply squeeze the handle on the gate and slide the gate out of the
Latch Catches.
7R&ORVH Squeeze the handle on the gate and slide gate until handle engages
and locks in Top Latch Catch.
7R5HPRYH*DWHIURP2SHQLQJSwing gate open until it is perpendicular
to opening and lift gate out of Hinge Brackets.
Children have died or been seriously injured when gates are not
securely installed.
• ALWAYS install and use gate as directed using all required parts.
• Install according to manufacturer’s instructions.
• STOP using when a child can climb over or dislodge the gate.
• Use only with the locking/latching mechanism securely engaged.
• NEVER use a gate to keep child away from pool.
• NEVER leave child unattended.
• Always close and lock the gate behind you.
• This product will not necessarily prevent all accidents. Proper adult
supervision is required at all times.
• Do not use if any components are missing or damaged.
• Adult assembly required. Exercise care when unpacking and
assembling product.
CAUTION KEEP SMALL PARTS OUT OF CHILD’S REACH.
WARNING
Colors and styles may vary.
0$'(,1&+,1$
1/19
6XPPHU,QIDQW86$,QF
1275 Park East Drive
Woonsocket, RI 02895 USA
1-401-671-6551
© 2019 Summer Infant (USA), Inc.
We’re here to help! If you have questions or need assistance,
please contact our Consumer Relations Team at
1-401-671-6551 or www.summerinfant.com/contact
7H[W³:RRG6WDLUZD\´WR
for a step-by-step installation video.
Have questions? :H¶UHKHUHWRKHOS
Contact our Consumer RelationsTeam
at 


6(783FRQWLQXHG
*
+
,
-
.
6WHSTo attach Upper Hinge Bracket: repeat step 4.
6WHSRemove Precision Fit Template. Attach Upper and Lower
Hinge Bolts on gates to the Hinge Brackets on wall (FIGURE E).
6WHSSnap Top Latch Catch to handle on Gate Panel (
FIGURE F) and extend gate outward until Top Latch Catch is
touching the wall.
6WHS To attach Top Latch Catch: Line gate up with wall.
Using a pencil, mark wall through top hole of Top Latch Catch
(FIGURE G). Swing gate out of the way, remove Top Latch Catch
from gate handle. Line Top Latch Catch up with mark on wall
with the top hole. Using pencil, mark wall through bottom hole
of latch. Be sure the Top Latch Catch is right side up. Place a
One-Direction Stop behind Top Latch Catch making sure that
the “protrusion” is on the stair side of the opening (FIGURE H).
1RWHOne-Direction Stops must be installed with the Latch
Catches to prevent gate from swinging both ways. Gate should
NEVER open over the stairs.
6WHS Pre-drill hole (3/32” or 2.4mm bit), then use Phillips head
screw driver and Long Screws to attach the Top Latch Catch.
6WHS To attach the Bottom Latch Catch: Slide the Bottom
Latch Catch into place (FIGURE I). Repeat steps 8 and 9.
6WHS Swing Gate closed and extend Gate until handle
is engaged.
6WHS To attach Stopper to Gate: Place Stopper on top of Gate
panel closest to hinge side. Location of Stopper should be
determined by width of Wrench head (FIGURE J).
1RWHStopper must be installed for one-directional stops to
function properly at top of stairs.
Be sure the door stopper is on the stairway side of the gate so the
gate cannot open over the stairs.
6WHS Pre-drill hole (3/32” or 2.4 mm bit), then use Phillips
head screw driver and short screw to attach the Stopper to the
Gate.
6WHSAdjust Support Foot to be gently contacting floor when
gate is closed and locked (FIGURE K).
,03257$17127( Be certain never to allow a gap between
sides of the gate and opening or bottom of the gate and floor to
exceed 3”. Once Gate is in place, check to ensure that it is
properly secured. Hinge bolts may be extended out to
accommodate maximum extension of 48”. Once extended as
desired, lock them in place with the Wrench.
(
)
)($785(&20321(176
*DWH +LQJH%ROW
+LQJH%UDFNHWV
VKRUWORQJ
6KRUW6FUHZ
6XSSRUW)RRW
)DVWHQHUV
6(783
$
6XSSRUW)RRW
$VVHPEO\
6WRSSHU
/RQJ6FUHZV
7R S
/DWFK&DWFK
:DOO$QFKRUV
2QH'LUHFWLRQ6WRSV
%RWWRP
/DWFK&DWFK
:UHQFK
$
&
'
,03257$17$WWKHWRSRIWKHODQGLQJSRVLWLRQWKHJDWHD
PLQLPXPRILQFKHVFPDZD\IURPWKHWRSVWHS
Screws are provided for mounting the brackets and latch catches
directly to wood. If mounting into wallboard, use the wall anchors
prior to using screws provided. If you are mounting the gate to
another surface, purchase and use the appropriate hardware.
1RWH ,IZDOODQFKRUVDUHQHHGHG:
D Pre-drill a hole in the wall (7/32” or 5.5 mm drill bit- drill and
drill bit not included).
E Insert the wall anchors (included) into the hole with a hammer,
tap gently until the head of the wall anchor is flush with the wall.
6WHS Attach the Support Foot Assembly to the bottom of the
Gate with the Support Foot Fasteners using the pre-drilled hole
(FIGURE A).
1RWH If baseboard exists, use long hinge bracket on top. If there is no
baseboard, use both short hinge brackets.
6WHS Use Precision Fit Template with Hinge Brackets on. Place
template against desired wall where gate will be located. Assure that
template is touching bottom of floor to limit gate spacing on bottom
of gate (FIGURE B).
6WHS To attach both Hinge Brackets: Using a pencil, mark the wall
through holes of Upper and Lower Hinge Bracket (FIGURE C).
6WHS
Pre-drill hole (3/32” or 2.4 mm bit), then use Phillips head
screw driver and 2 Long Screws to attach the Lower Hinge Bracket
to the wall (FIGURE D).

+DUGZDUH.LWLQFOXGHVSupport Foot Assembly, Precision Fit Template, One-Direction Stops (2),
Hinge Brackets (3), Stopper, Top Latch Catch, Bottom Latch Catch, Support Foot Fasteners, Short Screw,
Long Screws (8), Wall Anchors (8), and Wrench.
3OHDVHFKHFNRXUZHEVLWHIRUDFFHVVRULHVDQGUHSODFHPHQWSDUWV
%
3UHFLVLRQ)LW
7HPSODWH
TOP
FLOOR