Summer 4-in-1 SuperSeat User manual

4-in-1 SuperSeat®
Sit, Snack & Play!
INSTRUCTION MANUAL
Thank you for purchasing the 4-in-1 SuperSeat from Summer Infant.
This multi-use seat is designed to grow with your little one from approximately 4 months
to approximately 4 years of age, providing a safe place to sit, snack and play!
13360/13365
Please read the following instructions and warnings carefully
KEEP THIS INSTRUCTION MANUAL
FOR FUTURE REFERENCE.
Tool required: Phillips head screwdriver (not included).
For technical support, contact us at [phone].
or www.summerinfant.com/contact
For use with children from
approximately 4 months to 4 years (see page 8).
Adult assembly required.

WARNING
2
FALL HAZARD: Infants have suffered skull fractures falling while in and from floor seats:
· Use ONLY on the floor.
· NEVER use on an elevated surface.
· ALWAYS use restraints. Adjust to fit snugly.
· NEVER lift or carry child in the product.
· Use ONLY with a child that is able to hold their head up unassisted.
· STOP using when child can climb out or walk.
· ALWAYS keep child in view while in product.
· NEVER use the toybar to lift or carry product with child in it.
DROWNING HAZARD: Infants have drowned when floor seat has been placed in a bath tub or pool.
· NEVER use in or near water.
Children have suffered head injuries, including skull fractures, after falling with or from booster seats.
· Check that booster seat is securely attached to adult chair before each use.
· Always use restraint until child is able to get in and out of booster seat without help. Adjust to fit snugly.
· Never allow child to push away from table.
· Never lift and carry child in booster seat.
· Stay near and watch your child during use.
· ALWAYS secure BOTH back and seat straps to an adult chair.
· NEVER lift this product with your child in it.
· NEVER leave child unattended and without supervision.
· Prevent serious injury or death. Do not use in motor vehicles.
· NEVER use this product as a car seat or bath seat, on a table or counter top, stool, swivel chair, folding chair,
unstable chair or any chair where the straps cannot secure it properly.
· Minimum dimensions of adult chair that the booster seat shall be attached to: Seat width 18 in. and depth 18
in., and the seat backrest height is at least 8 in. tall.
· ALWAYS use product with plastic support insert securely installed, during all modes of use (as shown on page 8).
· Until child is able to get in and out of the booster seat without help (about 2½ years old), the child should be
secured in the booster seat at all times by the restraining system. The tray is not designed to hold the child in the
chair.
· Use this product only with children capable of sitting upright unassisted.
· Check that both the floor and seat of the chair are level before installing the booster seat.
· Prevent finger injury: Keep child away from chair when installing the tray.
· When in booster seat mode, use only feeding tray section and remove activity tray sections.
· Once installed, check the security and position of the booster seat.
· Do not use this booster unless all components are correctly fitted and adjusted.
· Discontinue use of the product if damaged, broken, or disassembled.
PREVENT FALLS: ALWAYS USE ADULT CHAIR STRAPS when using product on elevated surfaces as a booster seat.
Infant Floor/Support Seat Use:
Booster Seat Use:
WARNING

C
D
E
L
I
J K M
A
Seat Base
A
Fabric Seat
B
Track Toy
I
CSupport Insert
Plastic Support Insert
Backrest
D
Spinner Ball Tray
E
Shape Sorter Toys (2)
J
Center Tray
F
Feeding Tray
HShape Sorter Tray
G
Clip Toys (2)
K
L
Adult Chair Straps (4)
M
Long Screws (6)
N
OShort Screws (4)
B
components:
assembly:
click!
click!
Press the
backrest
down into the
seat base.
It will lock
into place.
13
H
FG
Activity Tray:
Hardware:
Note: Toddlers may not need the
support insert. Remove insert
from straps if desired.
Note: Ensure backrest and seat
base are fully connected. Test
stability and connection points
before use.
!
!
Seat Base will come preassembled
with: Child Restraint Straps,
Fabric Seat, Plastic Support Insert,
and Support Insert.
x6 x4
N O

assembly (continued):
Align the 2 screw holes in the
plastic support insert to the
those in the front base. Using
2 long screws, attach from the
underside of the base.
x 2
2
3
4
Flip the seat over.
Insert and fasten
the 4 long screws.
N
x 4
Helpful Hint: If possible, use a long screw-
driver on the two front screw locations.
!
Note: Bottom front T-straps will
be attached prior to first use. To
re-attach fabric seat if you need to
remove and machine wash it,
rethread T-straps through the slots.
!
N
x 2
Helpful Hint: This step
may be easiest with the seat
flipped over. You may need
to pull the fabric back
slightly to access the screw
holes.
!

assembly (continued):
5
Thread the three
T-straps on the back of the
fabric seat into the slots on
the backrest.
4
5
Insert the four plastic fasteners
into the keyhole slots on the front of the
seat frame. Slide fasteners to lock.
x 2
Insert the two plastic fasteners
on the underside of the
fabric seat into the
top of the seat frame.
x 2
6
x 3
Note: Pull up to ensure the straps are fully
inserted. They should not pull out of the slots.
!
x 2

assembly (continued):
Slide activity
tray into
track around
the backrest.
Connect track toy (I)
by inserting it
onto the activity tray.
Use 4 short screws
to assemble the
activity tray (F,G,H).
press!
press!
9
7
6
O
x 4
8
H
G
F

assembly (continued):
7
Connect feeding tray
to activity tray.
Clip toys (L)
onto loops on
each side of
the track toy.
click!
x 2
Note: It may help to
place one hand on the
back of the activity tray.
Pull on all sides of the tray
to ensure that it is fully
connected.
click!
!
FINISHED!
Connect the square and
triangle sorter toys (K)
by threading the T-straps
through the slots
in the activity tray.
11
10
12
Note: Pull up to ensure the straps are fully
inserted. They should not pull out of the slots.
!

modes of use:
Positioner/Support Seat Activity Center
Feeding Seat
Use on the floor or on an adult chair
(chair straps included).
Booster Seat
Use on an adult chair (chair straps included).
Fabric insert supports baby’s waist & back. Use
for babies just learning to sit up unassisted.
360º rotating tray allows easy transition between
feeding and activity time. Activity tray features
shape sorters, track toy with glider beads,
spinner ball & lock and key teethers.
43
21
8
WARNING
When seat is used
on adult chair, use
only the feeding
tray. Remove the
activity tray
sections.
!
Only use for children who are able to hold their head
up unassisted (approximately 4 months of age). Stop
using as a Positioner/Support Seat and Activity Seat
when child can walk or get in and out of product by
themselves (approximately 12 months of age).
!
Only use for children capable of sitting upright unassisted.
!

Pull the
lever beneath
the feeding tray
to release.
remove tray:
attach to adult chair:
9
x 4
L
Thread the
adult chair straps (L)
into the slots on the
underside of the
seat base.
1
Note: Pull up to ensure the straps are fully
inserted. They should not pull out of the slots.
!

attach to adult chair (continued):
storing adult chair straps:
child restraint:
be sure to
tighten straps!
fasten clips
around
chair back and
underneath chair
seat!
press in
to release
Once fully assembled,
a storage pocket is located
underneath the front of the seat.
This pocket is used to store
the adult chair straps.
Coil straps and insert.
Never use on an adult chair without securely
fastening chair straps. Always tighten adult
chair straps and test security before use.
IMPORTANT
10
2
Insert.
Press to
release.

removing fabric seat:
Remove the feeding
and activity trays.
11
x 3
Pull up the
two fasteners
on the underside
of the fabric seat
by lifting them up
and out from the
seat base.
Remove the
four fasteners
from the keyhole
slots on the front
of the seat base
by sliding out.
x 2 x 2
1
4
3
2
Remove the
three T-straps from the
slots on the backrest.
x 2

Please retain information
for future reference.
Colors and styles may vary.
MADE IN CHINA.
7/18
Summer Infant (USA), Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
401-671-6551
© 2018 Summer Infant (USA), Inc.
removing fabric seat (continued):
cleaning & maintenance:
•Fabric Seat & Support Insert: Machine wash, cold water, gentle cycle, no bleach. Tumble dry, low heat.
• Wipe frame with a damp cloth and mild soap.
• Do not use if any components are damaged missing, broken, or disassembled.
56
Remove the
two T-straps from the
slots underneath
the seat.
Remove insert &
fabric seat
from restraint
straps.
x 2
We’re here to help! If you have questions or need assistance,
please contact our Consumer Relations Team at
401-671-6551 or www.summerinfant.com/contact