Sunjoy Vineyard L-BS507SAL User manual

Vineyard 3pc Bistro Set - Rocking Chair
Item # L-BS507SAL
Congratulations on your purchase of our SUNJOY Vineyard 3pc Bistro Set. Our clear, easy
to follow, step-by-step instructions will guide you through the assembly process from start
to finish.
WARNING:
Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of the chair construction.
Keep assembly area at least 6 feet from any obstruction such as a fence, garage,
house, overhanging branches, laundry line or electrical wires.
Some parts may container sharp edges. When assembling and using this product,
basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and
use.
For outdoor use only.
Check all bolts for tightness before use, and periodically check and tighten bolts as
necessary.
IMPORTANT
Please take time to read these instructions thoroughly and follow each step carefully for safe and
easy operation. Keep this manual for future reference.
For technical assistance on assembly or replacement parts, call Sunjoy Industries at 1-866-578-6569
from 8:30AM to 5:30PM EST
,
or email us at sams
@
sun
j
o
yg
rou
p
.com for assistance.

Part List
No Description Qty Image
A Chair Rest 1
B Chair Base 1
C Foot Cap (Pre-assembled on Part B) 6
D Bolt 4
E Nut (Four nuts are pre-assembled on Parts A, J) 8
F Split Washer (Four Split Washers are
pre-assembled on Parts A, J) 8
G Flat Washer (Four Flat Washers are
pre-assembled on Parts A, J) 8
H T Frame (Pre-assembled on Part B) 1
I Square Washer (Four square washers are
pre-assembled on Parts A, J) 6
J Fiberboard (Pre-assembled on part A) 2
K Bolt (Pre-assembled on Parts A，J）4
L Plastic Base Cover (Pre-assembled on Parts B）1
M Wrench 1

Assembly Steps:
Attach the chair rest A to the Fiberboard J and the T Frame H of the Chair Base B using the
Square Washer I, and the Bolt D.
Connect together using the Flat Washer G, the Split Washer F, and the Nut E; then tighten
firmly using Wrench M.
Care &Maintenance
Before using, clean the chair completely with a soft dry towel. Do not place your chair in wet conditions where
there is a risk of rust developing. When not in use, wipe free of any dirt or loose objects, wash with a mild solution
of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. When
not in use, store in a cool, dry location away from sunlight.
Limited Warranty:
Sunjoy Industries warrants to the original purchaser that this item is free from defects in workmanship and
materials for a period of 1 year from the date of purchase, provided the item was factory-sealed at the time of
purchase and is maintained with care and used only for personal, residential purposes. Should any manufacturing
defect arise within this warranty period, Sunjoy Industries will repair or replace (at our option) any defective
merchandise upon proof of purchase; however, transportation and delivery costs, as well as payments to a third
party for assembly or disassembly of the item, remain the responsibility of the purchaser. A purchaser of an "open

box," previously-returned, or "clearance" item, as well as original purchasers outside of the warranty period, may
obtain replacement parts from Sunjoy Industries for products in current production, at nominal cost.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights,
and you may also have other rights, which vary from state to state.

Vineyard 3pc Bistro Set - Table
Item # L-BS507SAL
Congratulations on your purchase of our SUNJOY Vineyard 3pc Bistro Set. Our clear, easy
to follow, step-by-step instructions will guide you through the assembly process from start
to finish.
WARNING:
Keep all children and pets away from assembly area. Children and pets should be
supervised when they are in the area of the table construction.
Keep assembly area at least 6 feet from any obstruction such as fence, garage, house,
overhanging branches, laundry line or electrical wires.
Some parts may container sharp edges. When assembling and using this product,
basic safety precautions should always be followed to reduce the risk of personal
injury and damage to the product. Please read all instructions before assembly and
use.
Check all bolts for tightness before use, and periodically check and tighten bolts as
necessary.
IMPORTANT
Please take time to read these instructions thoroughly and follow each step carefully for safe and
easy operation. Keep this manual for future reference.
For technical assistance on assembly or replacement parts, call Sunjoy Industries at 1-866-578-6569
from 8:30AM to 5:30PM EST
,
or email us at sams
@
sun
j
o
yg
rou
p
.com for assistance.

Part List
No Description Qty
A Umbrella Cap 1
B Table Top 1
C Left side panel 1
D Right side panel 1
E Umbrella Tube 1
F Base 1
AA Split Washer M6 8
BB Spring washer M6 8
CC Bolts M6×20 8
DD Flat washer M12 1
EE Nut M12 1
FF Wrench M6 1
GG Wrench M12 1
HH Footpad
(pre-assembled onto F) 4
II Adjustable knob
（pre-assembled onto E）1
Step1:
Attach Right Side panel D onto the Base F,
tighten with bolt CC, flat washer AA, and
split washer BB. Repeat the same process
for the Left Side panel C.
Step 2:
Fasten the Umbrella Tube E into Nut EE on
Base F, tighten with flat washer DD, (Tool
needed: Wrench GG)

Care &Maintenance
Before using, clean the table completely with a soft dry towel. Do not place your table in wet conditions where
there is a risk of rust developing. When not in use, wipe free of any dirt or loose objects, wash with a mild solution
of soap and water; rinse thoroughly and dry completely. Do not use strong detergent or abrasive cleaners. When
not in use, store in a cool, dry location away from sunlight.
Limited Warranty:
Sunjoy Industries warrants to the original purchaser that this item is free from defects in workmanship and
materials for a period of 1 year from the date of purchase, provided the item was factory-sealed at the time of
purchase and is maintained with care and used only for personal, residential purposes. Should any manufacturing
defect arise within this warranty period, Sunjoy Industries will repair or replace (at our option) any defective
merchandise upon proof of purchase; however, transportation and delivery costs, as well as payments to a third
party for assembly or disassembly of the item, remain the responsibility of the purchaser. A purchaser of an "open
box," previously-returned, or "clearance" item, as well as original purchasers outside of the warranty period, may
obtain replacement parts from Sunjoy Industries for products in current production, at nominal cost.
Exclusions:
Items used for commercial, contract, or other non-residential purposes, or items damaged due to acts of nature,
vandalism, misuse, or improper assembly are not covered. Corrosion or rusting of hardware is not covered. Proof
of purchase (dated register receipt) is required for warranty claims. Warranty is to the original purchaser and is
non-transferable. Any replacement of warranted items will be in the original style and color, or a similar style and
color if the original is unavailable or has been discontinued. As some states do not allow exclusions or limitations
on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights,
and you may also have other rights, which vary from state to state.
Step 3:
Attach Table Top B onto side panels C/D,
tighten with bolts CC, flat washer AA, split
washer BB. (Tool needed: Wrench GG)
Step 4:
Place Umbrella Cap A onto Table Top B