Sunjoy L-GZ106PAL-1 User manual

Assembly Instructions
10’X12’ Aluminum Gazebo
Item# L-GZ106PAL-1
Our clear, easy to follow, step by step instructions will guide you through the project
from start to finish. Feel confident that this will be a fun and rewarding project. The
final product will be a quality piece that will go together smoothly and give years of
enjoyment.

Item Identification
For ease of identification all parts are labeled
to correspond to the Step number in which the
part is used.
A hammer and a ladder (more than 2m) are needed.

1A
Long Left Beam
2
1B
Long Right Beam
2
1C
Short Left Beam
2
1D
Short Right Beam
2
1E
Reinforcement Slat
4
1F
Corner Connector
4
2A
Canopy Spoke
Combination
2
2B
Lower Beam Connector
1
2C
Upper Beam Connector
1
2D
Large Fabric Cover
1
2E
Small Fabric Cover
1
3A
Pillar
4
3A1
Supporting Pole on Pillar
(Preassembled)
8
3B
Foot Cap
4
3C
Sun Panel
1
3D
Netting
1
TT
Plastic Hook
(Preassembled)
104
Parts List
(X74) AA
Bolt M6x15
(TBZ01206015HQ)
(X90) BB
Flat Washer M6
(TBZ10406HQ)
(X16) CC
Bolt M6X50
(TBZ01206050HQ)
(X12) GG
Peg ￠6x180
(TBZ10606180HQ)
(X2) WW
Socket Head Wrench
M6
(X18) HH
Bolt M6X28
(TBZ01206028HQ)
(Preassembled）
(X18) II
Nut M6
(TBZ20506HQ)
(Preassembled)
(X8)AA
Bolt M6X15
(TBZ01206015HQ)
(Preassembled）
Hardware pack

Step1
①Insert Long Right Beam(1B) into Long Left Beam(1A), and fix with Bolt M6X15(AA)，Flat Washer
（BB）. Insert Short Right Beam (1D) into Short Left Beam (1C) and fix with Bolt M6X15 (AA)，Flat
Washer（BB）(Figure 1& figure 2)
②Fix Long Right Beam(1B) and Short Left Beam(1C) with Corner Connector(1F) by using Bolt
M6X15(AA) and Flat Washer(BB). (Figure 3)
③Attach Reinforcement Slat(1E) to the beams with Bolt M6X15(AA)，Flat Washer(BB). (Figure 4)
Note: Please block up the whole frame to prevent the damage to the Plastic Hooks (TT) when assemble.
Make sure all snap buttons are in place.
BB
BB
1B 1C
AA
BB
AA
BB
AABB
BB
AA
1C
1D
1B
1A
1E
1C
AA
AA
fig.1
fig.2
fig.3
fig.4
BB
BB
BB
BB
BB
BB
Block
1A
1B
1C
1D
1E
1E
1E
1E
1F
1F
1F
1F
1A
1B
AA AA
AA
AA
1D
AA
AA AA
AA

Step2
①Open Canopy Spoke Combination(2A) and make sure the short tubes are on top. Insert Canopy Spoke
Combination (2A) into Lower Beam Connector (2B) and Upper Beam Connector (2C) respectively.
(Figure 5)
②Insert sway rod of Canopy Spoke Combination(2A) into Corner Connector(1F), and then fix Canopy
Spoke Combination(2A) and Long Left Beam(1A) with Bolt M6X15(AA)，Flat Washer(BB). Repeat
for the remaining Long Right Beam (1B), Short Left Beam (1C) and Short Right Beam (1D). (Figure 6
& Figure 7& Figure 8)
③Place Large Fabric Cover(2D) on the long tube of Canopy Spoke Combination (2A) ( Do not tighten).
Then place Small Fabric Cover (2E) on the short tube of Canopy Spoke Combination (2A) and tighten
it. (Figure 9)

3D
fig.14
fig.15
BB
3B
3A
AA
fig.10
fig.12
fig.13
GG
1B 1C
3A1
3A1
3A
3B
3B
3B
3B
3A
3A 3A
Now, your Gazebo is ready for use.
Step3
①Attach Foot Cap(3B) to Pillar(3A) with Bolt M6X15(AA) ，Flat Washer(BB). (Figure10)
②Attach Pillar(3A) to the assembled roof frame by using Bolt M6X50 (CC) and Flat Washer(BB).
(Figure11)
③Attach the Supporting Pole (3A1) to the beams with Bolt M6X15(AA) ，Flat Washer(BB). (Figure 12)
④Pound Peg (GG) into ground. (Figure 13)
⑤Straight the Large Fabric Cover(2D) and tighten. Put up Netting(3D) with Plastic Hooks(TT) of the
inside track, and then put up the Sun Panel (3C) with the Plastic Hooks (TT) of the outside track.
(Figure 14& Figure 15)
Note: 4 people are needed for step②

WARNING
1. When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and use.
2. Some parts may contain sharp edges, wear protective gloves if necessary. At least two or more
people are recommended for safe assembly.
3. Keep all children and pets away from assembly area.
4. At least 6 feet from any obstruction such as fence, garage, house, overhanging branches, laundry
line or electrical wires.
5. Install on level ground. This gazebo cannot be permanently staked or attached to concrete floor or
platform. This gazebo is intended for decorative and sunshade purposes only and is not meant to
withstand inclement weather including high winds, rain and snow. Gazebo fabric is water resistant,
not water proof and may leak during exposure to precipitation.
6. Check all nuts and bolts for tightness before and during usage.
WARNING: KEEPALLFLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous
contact with any flame source. The application of any foreign substance to the tent fabric may render
the flame-resistant properties ineffective.
This unit is heavy. Do not assemble this item alone.
Care & Maintenance
Our iron components for garden accessories and furniture are coated with rust inhibiting paint that
protects it from rusting. However, due to the nature of iron, surface oxidation (rusting) will occur
once these protective coatings are scratched. This is a natural process and is not a defect! To
minimize this condition, we recommend care when assembling & handling the product to prevent
scratching the paint. Should any scratching or damage occur, we recommend immediate touch-up
with rust inhibiting paint, which is included in the package. Surface rust can also be easily removed
with a very light application of common cooking oil. If surface oxidation (rusting) occurs and if no
measure is taken to prevent this, the oxidation may start dripping on to deck or patio and cause
damaging stains, which may be difficult to remove. This can be prevented if measure is taken to
keep the product from oxidizing.
Made in China