Sunny Health & Fitness SF-T7878 User manual

MAGNETIC TRAINING TREADMILL
SF-T7878
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions.
Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: [email protected] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT NOTE:
The belt must be lubricated before the first use! Please see Page 9 for instructions on how to
properly apply lubricant.
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled,
maintained, and used properly. It is your responsibility to ensure that all users of the equipment
are informed of all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if you
have any medical or physical conditions that could put your health and safety at risk or
prevent you from using the equipment properly. Your physician’s advice is essential if you
are taking medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
Stop exercising if you experience any of the following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of
nausea. If you do experience any of these conditions, you should consult your physician
before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use
only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or
carpet. To ensure safety, the equipment should have at least 8 feet (240 CM) of free space
behind it and 2 feet (60 CM) on each side. Do not place the treadmill on any surface that
blocks air openings. To protect the floor or carpet from damage, place a mat under the
treadmill.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The
safety of the equipment can only be maintained if it is regularly examined for damage
and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while
assembling or checking the equipment, or if you hear any unusual noises coming from the
equipment during exercise, discontinue use of the equipment immediately and do not use
until the problem has been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment
9. The maximum weight capacity of this unit is 300 pounds (135 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving
are required.
12.Your product is intended for use in cool and dry conditions. You should avoid storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only; it is not intended for commercial
use.

2
EXPLODED DIAGRAM
39
39
1
2
3
4
5
6
7
8
9
10L
10R
11
11
12
13 13
14
15
16
17 17
18
18
18
18
19 20
20 19 21
22
22
23
23
24
24
25
25 26
26
26
25 26 25
26 26
27
28
28
28
29
29
30
30
30
30
31
32
32
32
33
34
34
33
35
35
36
36
37
37
38
38
39
39
40
41
42 43
44
45
47
47
47
47

3
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1
Main Frame
1
25
Flat Washer
Φ8.2xΦ16x1.5
4
2
Handlebar
1
26
Nylon Nut
M8
6
3
Incline Adjuster
1
27
Socket Pan Head
Screw
M8*25*15
1
4
Front Roller
1
28
Socket Pan Head
Screw
M8*45*20
3
5
Rear Roller
1
29
Phillips Self Drilling
Screw
ST5.5*22
2
6
Running Board
1
30
Cushion Mat
4
7
Running Belt
1
31
Bolt
M6*50
1
8
Meter
1
32
Phillips Self Drilling
Screw
ST4.8*16
6
9
Cylinder
1
33
Phillips Button Head
Screw
M6*30
2
10R
Right Plastic Cover
1
34
Phillips Button Head
Screw
M6*40
2
10L
Left Plastic Cover
1
35
Bolt
M8*55
2
11
Side Rail
2
36
Round End Cap
2
12
Tension Control Knob
1
37
Spring
2
13
Hand Pulse
2
38
Square Rubber Mat
2
14
End Cap
2
39
Cushion Strip
4
15
Plug
1
40
Nut
M10
1
16
Plug
1
41
Plug
1
17
Screw
M5*15
5
42
Wire Clip
1
18
Phillips Self Drilling
Screw
ST4.2*13
4
43
Sensor Bracket
1
19
Bolt
M12*70*30
2
44
Sensor Wire
1
20
Flat Washer
Φ12*Φ24*2.0
2
45
Sensor Wire
Connector
1
21
Knob
M10*65
1
46
Allen Wrench
S6
1
22
Rubber Pad
2
47
Nut
M6
4
23
Transportation Wheel
2
24
Socket Pan Head Screw
M8*40*15
2
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
✓The model number (found on cover of manual)
✓The product name (found on cover of manual)
✓The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the
front of the manual)
Please contact us at [email protected] or 1- 877 - 90SUNNY (877-907-8669).

4
UNFOLDING INSTRUCTIONS
21
2
1
9
21
2
1
STEP 1:
Remove Knob (No. 21) by rotating it
counter-clockwise. Then, simply give the
treadmill a light kick to the position on
Cylinder (No. 9) that the arrow points to.
Let Main Frame (No. 1) lower slowly on
its own.
STEP 2:
Once the Main Frame (No. 1) touches the
ground, attach Knob (No. 21) into the
hole on Handlebar (No. 2). Rotate the
Knob (No. 21) clockwise to tighten. The
unfolding is complete.

5
FOLDING INSTRUCTIONS
21
2
21
2
1
9
STEP 1:
Remove the Knob (No. 21) by rotating it
counter-clockwise. Lift up Main Frame
(No. 1).
STEP 2:
Once the Cylinder (No. 9) is in place,
align the holes on Main Frame (No. 1)
and Handlebar (No. 2), then attach Knob
(No. 21) into the holes. Rotate the Knob
(No. 21) clockwise to tighten. The folding
is complete.

6
HOW TO ADJUST THE INCLINE
Pull out Incline Adjuster (No. 3), rotate the Incline Adjuster (No. 3),and push it into the
desire incline. This completes the incline adjustment.
1 1
11
33
33

7
HOW TO MOVE THE TREADMILL
23
2
2
23
23
2
2
Before attempting to move the treadmill,
make sure that it has been properly folded.
To tilt, start by placing one hand at
Handlebar (No. 2) to support the treadmill.
Next, place one foot on Transportation
Wheels (No. 23) to hold the bottom end of
the treadmill steady. With your foot at
Transportation Wheels (No. 23), slowly tilt
Handlebar (No. 2) downward towards the
ground. Once Handlebar (No. 2) reaches a
low enough point, the Transportation
Wheels (No. 23)will touch the ground.
To transport, hold Handlebar (No. 2) and
tilt until Transportation Wheels (No. 23)
are able to move on the ground.

8
MAINTENANCE INSTRUCTIONS
CENTERING THE RUNNING BELT:
If the Running Belt (No. 7) is off-center, the unit will make noise. Please use the tool to re-
adjust the Running Belt (No. 7) if it is too loose or too tight.
1. When the Running Belt (No. 7) moves to the right side, please turn the right side Bolt (No.
35) clockwise 1 or 2 circles, and then turn back slightly.
2. When the Running Belt (No. 7) moves to the left side, please turn the left side Bolt (No.
35) clockwise 1 or 2 circles, and then turn back slightly.
3. When the Running Belt (No. 7) is too tight, please turn the left and the right side Bolt (No.
35) counter-clockwise, and then turn back slightly.
4. When the Running Belt (No. 7) is too loose, please turn the left and the right side Bolt (No.
35) clockwise, and then turn back slightly.

9
TREADMILL LUBRICATION
IMPORTANT NOTE:
You will need to lubricate your treadmill before the first use!
RUNNING BELTS & TREADMILL LUBRICANT:
Lubricating the Running Belt (No. 7) & Running Board (No. 6) is essential as the friction
between the two affects the life span and operations of the treadmill. Inspect the Running Belt
(No. 7) regularly. If you find any wear on the Running Board (No. 6), please contact us at
[email protected].
Lift one side of the Running Belt (No. 7) and touch the top surface of the Running Board (No.
6). If the surface is dry, lift one side of the Running Belt (No. 7) and at the same time apply
lubricant to the Running Board (No. 6). Make sure to walk on your treadmill at a slow speed
for the first 3-4 minutes of use after applying lubricant. This helps to distribute the lubricant
equally.
NOTE: Do not apply lubricant over the belt. Any excess lubricant should be wiped off.
Lubricant may be applied whenever friction occurs, but it is usually required every 50 hours of
use. Please remember that this is only a guideline based on average treadmill use, your
schedule may vary.
ADJUSTING THE TENSION
There are 16 resistance levels on this Tension Control Knob (No. 12). Number 1 is the
lowest resistance; number 16 is the highest resistance. To increase the tension, turn the knob
clockwise;To decrease the tension, turn the knob counter-clockwise.

10
METER INSTRUCTIONS
FUNCTION BUTTONS
MODE: Press the Mode button to select the function displayed. Press
and hold the Mode button for 3 seconds, all the function values except
Odometer will be reset to zero.
SET: To set up the target value of Time, Distance, and Calories. You
can hold the button to increase the value fast. (No motion should be
detected at the time of setting).
RESET: Press the button to reset Time, Distance, and Calories.
Press and hold the Reset button for 3 seconds, all the function values except Odometer will be
reset to zero.
FUNCTIONS AND OPERATIONS
1. BATTERY INSTALLATION:
Please install 2 pieces of AA 1.5V batteries in the battery case on the back of monitor.
(When batteries are removed, all the functions values will be reset to zero.)
2. AUTO ON/OFF:
While the user starts to exercise, the meter will show the workout value automatically. When
inactive for over 4 minutes, the meter will turn off, but the workout value of odometer will be
held. When the user starts to exercise again, the workout value on the odometer will
accumulate continuously.
3. AUTO SCAN:
After the meter is powered on or the Mode button is pressed, the LCD will display all
functions values from Time-Calories-Odometer-Pulse-Speed-Distance. Each value will be
held for 6 seconds.
4. SPEED:
Displays the current training speed from 0.0 to 99.9 MPH. The user also can press Mode
button to display the Speed value.
5. DISTANCE:
Displays the trip distance from 0.0 to 999.9 Miles. The user also can press Mode button to
display the distance value. Press the Mode and Set button to preset Distance.

11
6. TIME:
Displays the workout time from 00:00 to 99:59. The user also can press the Mode button to
display the workout time value. Press the Mode and Set button to preset Time.
7. CALORIES:
Displays the calories burned during training from 0.0 to 9999. The user also can press the
Mode button to display the calories burned. Press the Mode and Set button to preset
Calories.
8. ODOMETER:
Displays the total accumulated distance from 0.0 to 999.9. The user also can press the
Mode button to display the odometer value.
9. PULSE:
Displays the current heart rate in beats per minute. The user can also press the Mode
button to display the odometer value.
NOTE:
1. If the meter display is abnormal, please re-install the batteries and try again. If the meter is
still not displaying properly, replace the batteries.
2. Battery Spec: 1.5V UM-3 or AA (2PCS).
3. Do not mix battery types and do not mix old and new batteries. Dispose or recycle batteries
according to your state and local rules.
Version:1.1