Sunrise Medical Quickie Xtender User manual

XTENDER KIT
QUICKIE NITRUM/QUICKIE 7R/QUICKIE Q7
Sunrise Medical 2842 N. Business Park Ave Fresno, CA 93727 USA
© 2022 Sunrise Medical (US) LLC
06/2022 243956 Rev.B Page 1of2
Customer Service: [phone]
or visit www.SunriseMedical.com
Please read these instructions carefully before beginning the assembly. Failure to understand and
follow assembly instructions may result in injury to the technician and/or end user and may void
the warranty. If you have any questions call Sunrise Medical Technical Support at [phone].
Required tools:
1. 5mm hex key
2. Torque wrench
Parts:
1. Pin sleeve (x2)
2. Axle clamp (x2)
3. Axle bracket (x2)
4. Socket head screws
1/2-in (x4)
5. Socket head screws
5/8-in (x4)
6. Clamp bracket (x2)
DEALER/TECHNICIAN WARNING
Attention dealers and qualified technicians, do not operate or service this device without first reading the owner’s manual.
If you do not understand the instructions and warnings in the owner’s manual please contact the Quickie Technical Service
Department before operating and/or servicing the Quickie device. Failure to do so may result in damage and/or injury.
Find more information and important warnings in the Xtender owner’s manual or at: www.SunriseMedical.com.
A. PRE-ASSEMBLY
1. Prep the chair:
a. Remove the wheels.
b. Place the chair on a flat work surface
or workbench for best assembly results.
B. XTENDER MOUNTING
1. Assembly of frame mounts:
a. Using a 5mm hex key, assemble the pin sleeve (item 1) to
the axle bracket (item 3) using the 1/2-in screws (item 4).
Assemble both left and right assemblies and note
orientation (Fig 2). Do not fully tighten until the mounting
hardware is on the frame.
b. Fit axle clamp (item 2) around frame axle. Attach assembly
from step 1 to clamp using 5/8-in screws (item 4). Leave
loose. See figures 3 and 4.
21 34
5
2
3
4
6
Left
Right
6
1
1
Right Side Left Side
2
Right
Left
Full assembly reference
7R/Q7 4
Right
Left
Full assembly
reference
Nitrum
3

XTENDER KIT
QUICKIE NITRUM/QUICKIE 7R/QUICKIE Q7
Sunrise Medical 2842 N. Business Park Ave Fresno, CA 93727 USA
© 2022 Sunrise Medical (US) LLC
06/2022 243956 Rev.B Page 2of2
Customer Service: [phone]
or visit www.SunriseMedical.com
C. CLAMP BRACKET
1. Assembly of wheels:
a. Attach clamp brackets to wheels. See figure 5 (left
wheel) and figure 6 (right wheel).
D. XTENDER WHEELS
1. Attach wheels:
a. Lift lever on Xtender wheel and slide axle into chair axle.
b. Ensure that clamp bracket pin is engaged into pin
sleeve.
c. Tighten hardware enough so it cannot move. Remove
wheel.
d. Torque hardware to 9.14 Nm [30 ft-lbs].
WARNING
Attention dealers and qualified technicians, ensure that
the mounted axle plate provides the same seat to floor
height as the original approved setup.
E. INSPECT
1. Double-check orientation and torque on all hardware:
a. Axle detent balls are fully extended.
b. Clamp bracket pin is fully engaged into pin sleeve.
c. Check that the chair rolls smoothly and evenly.
d. Check that axles have been mounted evenly from side
to side.
e. Use a torque wrench and socket wrench to check all
hardware for correct torque.
f. See Yamaha owner’s manual for additional information.
56
78
7
Clamp
bracket
pin
Wheel
axle
Pin
sleeve
Chair
axle
8
6
Right
Left 5