Suntec Wellness KLIMATRONIC HEAT SUPREME User manual

HEAT SUPREME
Micathermic Panel Heater/ Towel Warmer
Instruction Manual

2
IMPORTANT SAFEGUARDS
Please read all the instruction before using this heater.
1. To avoid burns, do not touch the hot surfaces of the heater when it is in use. Use handle
when moving this heater. Keep combustible materials, such as drapery and other
furnishings at least 3 feet (0.9m) from the front of the heater and away from the side and
rear.
2. Extreme caution is necessary when any heater is used by children, near children or
invalids whenever the heater is operating or unattended.
3. Do not use outdoor.
4. This heater is intended for use in bathrooms, laundry areas or similar indoor locations.
Never put heater where it may fall into a bathtub or other water container.
5. This heater has hot and arcing or sparking parts inside. Do not use in an area where
gasoline, paint or flammable liquids are used or stored.
6. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage the heater.
7. Always unplug heater when not in use. To disconnect heater, remove plug from outlet or
disconnect the power from the mains.
8. Using of extension cord is not recommended as it may overheat and cause a risk of fire.
However, if an extension cord has to be used, the conductor wire inside the cord must be
at least 1mm in diameter and rate not less than 13Amp.
9. Do not run cord under carpet and do not cover cord with throw rugs, runners, or the like.
Place the cord away from traffic area and where it will not be tripped over.
10. Never use a damaged cord or plug. If the supply cord is damaged, it must be replaced by
the manufacture, an affiliate agent or a qualified person in order to avoid hazard.
11. Connect the heater to properly grounded outlets only.
12. Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
13. Do not use this heater with a programmer, timer or any other device that switches the
heater on automatically.
14. Do not use the heater in the immediate surroundings of a bath, a shower or a swimming
pool.
15. The heater must not be located immediately below a socket outlet.
16. To avoid over-heating since a fire risk exists, do not cover the heater.
17. Only qualified service representative should perform repairing and maintenance services.
18. CAUTION: In order to avoid hazard due to inadvertent resetting of the thermal cut-out, this
appliance must not be supplied through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by the utility.
19. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
INTRODUCTION
This new type of heater uses MICATHERMIC heating element. The latest leading technology
using radiant energy: the appliance heats up objects and surrounding walls instead of just
warming up the air. Objects absorb heat energy and then gradually warm up the room.
Special Features
1. Instantly to full power of heating
2. Degrees of protection: IP24
3. Electronic thermostat control setting
4. Anti-Frost function
5. Safety thermal cut off
6. Light weight

3
7. Quiet
8. No oil-leakage
9. Towel rails to hang and dry towels
SPECIFICATIONS for HEAT SUPREME
Voltage rating: 230V AC, 50Hz
Power consumption: 1000W
Unit size: ca. 59.5 cm(L) × 80 cm(H) × 21.5 cm(W)
Unit weight: ca. 8.0 kgs
Unit Layout Electronic version (HEAT SUPREME)
1. On/off switch
2. Thermostat knob
3. Power light indicator
4. Functions knob
5. Metal grid
6. Rails
7. Built-in Handle
8. Mounting Hole
9. Mounting Support
10. Screws
11. Mounting Anchor for wall mounting
12. Screws for rails installation
13. Lower wall mounting support
14. Small screw for lower wall mounting
REMOVE PACKAGING
Please read all the instructions before using this heater
1. Take out the heater from gift box.
2. Remove the polyfoam and polybag.
3. Inside are:
1 bag with 1 Mounting Support, 4 screws, 4 Mounting Anchors for wall mounting
4 screws to fix the rails.
4. Save the packaging for storage when the heater is not been used or in summer season.
RACKS INSTALLATION
Screw the rails on the heater using the 4 special screws. It has to be done before the
installation of the heater on the wall.
LOWER WALL MOUNTING SUPPORT INSTALLATION
In the same polybag than the screws, there are 2 metal parts to fix at the bottom of the rear of
the heater. Use the 2 small screws, tighten firmly.

4
INSTALLATION
Heater has to be mounted minimum 0.7m from the floor and no object (e.g. Shelf) should be
placed within 1m from the top of the heater.
We recommend to install the heater in the bathroom area at least 0.6m away from shower OR
bathtub as shown in the picture (volume 3). The figure 0.6m is a suggested distance; the
actual distance from the shower and bathtub should follow national standard in each country
Once the racks are mounted, you can start the following steps to install the heater on the wall.
STEP IMark the left or right screw hole position using a pencil on the
wall (about 1.5 meter from floor)
STEP II
Drill a hole
STEP III
Hammer the screw anchor into the hole
STEP IV
Screw lightly the mounting support on the wall
STEP V
Mark another screw hole on the wall at the same level than the
first one and at a distance of 138mm approximately
STEP Vl
Drill second hole
STEP VII
Hammer another screw anchor into the hole
STEP VIII
Screw tightly the mounting support

5
STEP IX
Install the heater on the mounting support. Using
a pencil, mark the screw holes (left and right)
positions for the lower wall mounting support.
Then remove the heater from the wall mounting
support.
STEP X
Drill both holes.
STEP XI
Hammer the 2 remaining anchors into the holes.
STEP XII
Install the heater on the wall mounting support
and screw tightly the 2 remaining screws of the
lower wall mounting support.
OPERATION
Please read all the instructions before using this heater.
Electronic version
1. Ensure that the Temperature Control Knob is on minimum position. Also, make sure the
power switch is on “OFF” position.
2. Plug the power cord into a suitable electrical outlet. (Rating is not less than 13AMP)
3. Choose the function with control knob.
Function Description
☼Comfort The heater will operate at the thermostat setting
ECO The heater will operate 4
O
C below the thermostat
setting, without changing the thermostat position
Anti-Frost The heater will operate in “Anti Frost protection”
mode. (Approximately 7
O
C)
4. Turn on the on/off switch; the light indicator will turn on, than adjust the temperature
control knob clock-wise. Once the thermostat knob position is set at a higher level than
the actual room temperature, heat starts to be emitted. According to the personal needs
of the users, you can adjust the temperature control knob to increase or decrease the
room temperature in a clock-wise or anti-clock wise direction.
Anti Frost Function
It will keep the room temperature above “Freezing Point”. Simply plug-in the power cord, and
position the Temperature Control Knob on the “Snowflake” position. Pipe breakage by ice
will be avoided.

6
User Advice:
If you will be away for several hours, consider reducing the temperature setting.
If you have several appliances in one room, let them operate simultaneously. Therefore
you will obtain a more homogeneous temperature without increasing your electricity
consumption.
When you are airing a room, switch off the appliance.
CLEANING
1. Before cleaning, turn off the heater, unplug the power cord and allow the heater to cool
down.
2. Do not immerse power cord and plug or heater in water or other liquid. Do not pour water
or other liquid over the heater.
3. Use a vacuum cleaner to remove dust and lint on the metal grid of the heater.
4. Wipe the heater with a dry cloth to remove dust and a damp cloth (not wet) to clean off
strains.
5. Do not use detergents, abrasive cleaning powder or polish of any kind on the body of the
heater, as these can damage the finish.
STORAGE
Store the heater in a cool dry place. To prevent dust and dirt getting in the heater, use the old
packaging to repack the unit.
If the heater is not used regularly or if it is store uncovered, the heater may produce small
amounts of smoke and/or smell upon first use. This is normal; it is due to the accumulation of
humidity and dust on the heating element.
CHECK THE HEATER BEFORE REPAIRING
Heater not warm
1. Check if the heater is turned on or not?
2. Check the Thermostat Control Knob is on maximum position or not?
3. Check if any objects are covering the unit or not?
Heater not operating
1. Check if the power cord is plugged into an electrical outlet or not?
2. Check if the electrical supply in the house or the main fuse is working or not?
3. Make sure the power switch is on.
4. Check if the Thermostat Control Knob is on maximum position. (Ensure the light indicator
is on)
If after following the above checks the heater is still not operating please contact the
manufacturers’ service agent. All repairs must be referred to authorized personnel from
authorized retailer.
Important: Any tampering with the appliance will invalidate the warranty. Repairs carried out
improperly and by unqualified persons may have serious consequences for the user.
RECYCLING
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be disposed of with household
waste. Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice in your country
KEEP THESE INSTRUCTIONS