Sunwave Tech. SRC-3310/9320 User manual

SRC-9310/9320
Touch Screen Remote Control
User Manual
031021

SRC-93 SERIES User’s Manual
ii
Preface
About this manual
This manual is designed to make using the SRC-93 SERIES Touch
Screen Remote Control as easy as possible. Information in this
document has been carefully checked for accuracy; however, no
guarantee is given to the correctness of the contents. The information in
this document is subject to change without notice.
Copyright
© Copyright 2003
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by
any mechanical, electronic or other means, in any form, without prior
written permission of SUNWAVE Technology Corporation.
Trademarks
All trademarks and registered trademarks are the property of their
respective owners.

ii
i
Table of Contents
Chapter 1 - Introducing the SRC-93 SERIES.....................................1
SRC-93 SERIES Features .......................................................... 2
Unpacking the SRC-93 SERIES ............................................... 2
Identifying Components ....................................................... 3
Chapter 2 - Getting Started .............................................................4
Features Overview ................................................................. 4
Installing Batteries ................................................................... 6
Battery Low Indicator............................................................. 7
Battery Tips and Precautions ................................... 7
Touch Screen .......................................................................... 8
Turning the Touch Screen On.................................. 8
Touch Screen Precautions ....................................... 8
Touch Screen Buttons............................................... 9
Rubber Buttons........................................................................ 9
Menus ..................................................................................... 10
Setup Menu ........................................................................... 11
Delete Menu ......................................................................... 12
Macro Menu ......................................................................... 12
Chapter 3-Setting Up the SRC-93 SERIES to Control a Device.....13
Choosing a Device .............................................................. 13
Creating a New Device ...................................................... 13
Modifying an Existing Device ................................ 14
Re-Labeling Devices ............................................................ 14
Changing Touch Screen Layout ........................................ 15
Programming Infrared Codes............................................. 16
Using Manufacturer Codes................................................. 17
Using the Learning Function ............................................... 20
Collecting Unrecognized Infrared Codes ........................ 24
Deleting a Specific Key ....................................................... 25
Deleting a Device ................................................................ 25

SRC-93 SERIES User’s Manual
iv
Chapter 4 - Controlling Devices ................................................... 27
Selecting Device to Control ............................................... 27
Changing Touch Screen Page........................................... 27
Controlling the Device......................................................... 28
Using the AUX Key ................................................................ 28
Chapter 5 - Creating and Using Macros ...................................... 29
Introduction to Macros........................................................ 29
Creating a Macro Sequence ............................................. 29
Using Macros ......................................................................... 32
Deleting a Macro ................................................................. 32
Chapter 6 - Other Features............................................................ 33
Using Timers............................................................................ 33
Setting Up a New Timer .......................................... 34
Using Quick Channel Lists.................................................... 35
Setting up Quick Channel Lists.............................. 36
Deleting Channels from a Quick Channel List ... 37
Using Quick Channel Lists ...................................... 38
Transmitting System Setup................................................... 38
Using Sleep Mode................................................................. 39
Displaying Version Number ................................................. 40
Date and Clock .................................................................... 40
Power Down Time Period .................................................... 41
Backlight On Time Period .................................................... 41
Beep Toggling ....................................................................... 42
Resetting to Factory Defaults ............................................. 42
Appendix A - Specifications ......................................................... 43
Appendix B - Accessories ............................................................. 44
Appendix C - Troubleshooting...................................................... 45

1
Chapter 1 - Introducing the SRC-93 SERIES
Congratulations on your purchase of the SRC-93
SERIES Touch-Screen Remote Control. The SRC-93
SERIES is a digital universal remote control that is easy
to use, enabling you to control all of your electronic
devices equipped with an infrared (IR) remote.
The SRC-93 SERIES uses a touch screen panel and
control buttons and is simple to use. Simply select a
device and the appropriate screen appears. You can
control up to sixteen devices, including VCRs, DVDs,
TVs, and satellite dishes.
The SRC-93 SERIES is easy to set up. You can quickly
configure each device in your household or office
bye “learning eye”. You can quickly configure each
device in your household or office. In addition, the
advanced macro function enables you to initiate a
chain of up to 60 commands with the touch of a
single button.
Convenient and easy to use, the SRC-93 SERIES
provides you with a central control solution.
This manual will help you learn how to use all the
advanced features of the SRC-93 SERIES. It will not
explain how to use the functions for your devices.
Please refer to your device’s user manual for information
related to your device.
SRC-93 SERIES refers as SRC-9310, SRC-9320
Model Dimensions(W*D*H) Alkaline Battery
SRC-9310 3.2”x7.3”x1.2”
(8.2cmx18.5cmx3.2cm) 4 x AA
SRC-9320 3.2”x7.3”x1.1”
(8.2cmx18.5cmx2.9cm) 4 x AAA

SRC-93 SERIES User’s Manual
2
SRC-93 SERIES Features
The following list identifies the SRC-93’s key features.
•Large touch screen display.
•Macro sequence function—each macro can store 60
commands.
•Controls up to sixteen devices including DVDs, TVs,
Satellite Receivers, VCRs and CDs.
•Learns the IR codes from your existing remote controls
to quickly set up devices.
•Pre-programmed manufacturer’s codes for many
models.
•User programmable buttons for each device include
seven rubber buttons, the device key and forty-eight
soft buttons.
•Optional PC Interface for connection to a personal
computer.
Unpacking the SRC-93 SERIES
After you have unpacked the SRC-93 SERIES, check the
contents to make sure the following items are included.
•SRC-93 SERIES
•This User’s Manual
•Pre-programmed Code List
If any of the above items are missing or damaged,
please contact your dealer immediately. Do not throw
the shipping carton away in case you need to ship your
SRC-93 SERIES.

3
Identifying Components
Please refer to the following illustrations to identify
the components of the SRC-93 SERIES.
Figure 1: Front and Rear Views
Infrared Eye
Point the infrared
eye at the device
you want to
operate.
Touch Screen
The Touch Screen
panel enables you
to configure and
operate your
devices by
touching the
screen. Tap the
screen once to
turn on the
SCR-93 series.
Learning Eye
Point your device’s
remote control at this
eye to enable the
SCR-93 series to learn
your device’s infrared
codes.
Battery Cover
Remove this cover
to insert Alkaline
batteries.

SRC-93 SERIES User’s Manual
4
Chapter 2 - Getting Started
This chapter will give you the information you need
to know to quickly get using the SRC-93 SERIES as
your single remote control.
Features Overview
The following illustration highlights the different
sections of the SRC-93 SERIES.
Figure 2: SCR-93 SERIES Overview
Function Keys
SETUP Menu
DELETE Menu
MACRO Menu
UART Port
LCD Indicators
Beep On
Battery Low
Infrared OK
Error
Page1
Page 2
Touch Screen
Page / Date Key
Press and hold Page/Date Key
To see date and week. Device Ke
y
s
Learning Eye
Backlight / Sleep Key
Q CH Keys
Only key icons show
NEWS`SPORTS`
MOVIES`EDUCATION &
KIDS to have
Quick Channel selection
function.

5
•LCD Indicators: LCD stands for Liquid Crystal Display and
these indicators at the top of the display give you
feedback and information. You can look here to see if
the beep is turned on, if the battery has low power, if the
infrared signal was sent OK or if there was an ERROR, and
also to see which page of Touch Screen buttons you are
looking at.
•UART Port: This port allows you to connect the SRC-93
SERIES to a personal computer. See Appendix B -
Accessories on page 44 for more information.
•Backlight / Sleep Key: If pressed quickly, this key will
activate the Touch Screen backlight. If held down for
two seconds you will enter the Sleep menu.
•Page / Date Key: This key allows you to switch between
Page 1 and Page 2 of Touch Screen Buttons. If held
down for two seconds you will see the date and year
then week .
•Learning Eye: This is an infrared sensor used to detect
other remote controls infrared signals. Aim your existing
remote control here when using the SRC-93 SERIES’s
Learning Function.
•Device Keys: These keys allow you to switch between
different devices. Each key may have more than one
device. (For example, the TV key may have TV1 and TV2
for different TVs in your house.) Repeatedly press the
same device key to cycle through all the device names
assigned to that key. The SRC-93 SERIES includes 8
devices as the default with a total of 16 devices
maximum.
•Touch Screen: The touch screen acts as a “virtual”
keyboard on the SRC-93 SERIES. The display is normally
blank when the remote is not in use and can be
activated by simply touching it.
•Function Keys: These keys allow you to enter the SETUP,
DELETE, and MACRO menus. To enter the menu, touch
the function key for two seconds.

SRC-93 SERIES User’s Manual
6
Installing Batteries
The SRC-9310 operates on four AA Alkaline batteries,
SRC-9320 operates on four AAA Alkaline batteries
(batteries are not included). Batteries must be
inserted before you can operate the SRC-93 SERIES.
To insert the batteries, refer to the following illustration:
Figure 3: Installing Batteries
1. Turn the remote over, push on the tab and lift the cover
off.
2. Insert the batteries, matching the batteries to the (+)
and (-) marks inside the battery case.
3. Snap the battery cover back into place.

7
Battery Low Indicator
When the batteries are low, the battery low icon will
be displayed in the upper left hand corner just above
the SETUP button:
Figure 4: The Battery Low Icon
Battery Tips and Precautions
•Immediately replace the batteries when the battery low
icon appears.
•The SRC-93 SERIES will not lose programmed data when
batteries are replaced
•Always use fresh batteries. Alkaline batteries are
recommended. Do not mix different types of batteries.
•Be sure that the positive (+) and negative (-) polarities of
the batteries match the diagram shown in the
compartment.
•Do not expose the batteries to excessive heat or flame.
•Keep batteries out of the reach of children.
•Weak batteries reduce the effective distance of the
unit.
•To reduce danger of leakage and damage, remove
used batteries when used longer than two years.
When the battery Low Icon appears, you will not allowed
to enter Functions Keys (SETUP Menu, DELETE Menu &
MACRO Menu).

SRC-93 SERIES User’s Manual
8
Touch Screen
The touch screen reduces the number of buttons by
changing its configuration for each device selected.
In this way, the touch screen can provide a total of
768 buttons (16 devices x 2 pages x 24 buttons per
page).
Turning the Touch Screen On
Using the touch screen is easy. Simply touch the
screen to activate it. It will turn itself off after the user
programmable power down time period. (To change
the time, see Power Down Time Period in Chapter 7 -
Changing SRC-93 SERIES Parameters.)
Figure 5: Touch the Screen To Turn It On
Touch Screen Precautions
Please read the following instructions carefully:
•Tap the LCD touch screen gently; never use force.
•Do not use a pen or any sharp object to tap the screen.
You might damage the surface.
•Keep the touch screen dry. Wipe off any spills
immediately. The SRC-93 SERIES is not waterproof; never

9
immerse it in liquid.
•Don't expose the SRC-93 SERIES to extreme temperatures.
Keep it away from heat sources.
•Avoid dropping the SRC-93 SERIES.
•Don't drop anything on the touch screen.
•Clean the LCD touch screen with a soft cloth. If needed,
dampen the cloth slightly before cleaning. Never use
abrasives or cleaning solutions.
Touch Screen Buttons
The touch screen buttons enable you to operate
the SRC-93 SERIES and your external devices. Use
these buttons to program codes from your existing
remotes, control your devices and set up
command sequences called macros. You will hear
a beep when you press a button. To activate or
deactivate the beep, please see Beep Toggling on
page 42. The SRC-93 SERIES will turn itself off after a
user specified time period. To change the time
period, please see Power Down Time Period on
page 41.
Rubber Buttons
The buttons on the bottom part of the SRC-93 SERIES
allow you to operate devices as well as help program
the SRC-93 SERIES.
There are three rubber buttons that have special
functions:

SRC-93 SERIES User’s Manual
10
•Page / Date Button: Toggles from Page 1 to
Page 2 of the Touch Screen buttons. If held down
for more than two seconds, the date and year
then week will be shown.
•Power Button: Can turn off and on your devices
but also during Touch Screen Layout (see page
15) will display all possible LCD choices.
•Backlight / Sleep Button: Pressing it quickly will
turn on the backlight, while holding it down for
two seconds will enter the SLEEP Menu.
Menus
In order to use the menu buttons as SETUP, DELETE,
and MACRO you will first need to press and hold the
menu button for two seconds. This is to prevent
accidental menu entry.
As an additional safety feature, four numbers will
appear which will need to be pressed before the
menu will appear. This is simply to make sure you
meant to enter the menu and you can enter the
numbers in any order you like.
Figure 6: Confirm Menu Entry by Pressing Numbers

11
Setup Menu
Menu
Item
Description page
DATE Set the system clock and date. 40
NEW Create a new device from scratch. 13
CODE Assign a preprogrammed manufactures
infrared code to a device. 17
LABL Rename a Device. 14
LAY Change the Touch Screen layout to you want
to have based on all possible LCD choices. 15
LRN Learn infrared codes from an existing remote
control. 20
PWDN Set the automatic power off time period. 41
LITE Set the backlight time period. 41
DBUG Collect unrecognizable (un-learnable)
infrared codes. The SRC-93 SERIES cannot
learn 100% of all existing codes so it may be
necessary to collect the some codes and
email them to SUNWAVE. An updated
version of the SRC-93 SERIES system software
will be sent to you. See page 24 for more
info.
24
TRAN Transmit system software(MCU Program,
Flash Memory Data or Preprogrammed
Code only in Flash Memory Data) or infrared
codes from an SRC-93 SERIES to an SRC-93
SERIES or from an SRC-93 SERIES to a personal
computer.
38
VER Display the PROG & DATA version number. 40
BEEP Toggle the key-press beep. 42

SRC-93 SERIES User’s Manual
12
Delete Menu
Menu
Item
Description page
KEY Allow you to delete the infrared codes for a
specific Touch Screen or Rubber button. 25
BANK CODE: Allows you to delete all infrared
codes for a specific device while leaving the
Touch Screen layout the same.
ALL: Deletes both infrared codes and the
touch screen layout for a specific device.
25
RST Resets the SCR-9310 back to factory settings. 42
Q CH Allow you to erase any channel that is stored
in one of the Quick Channels. (NEWS,
SPORTS, MOVIES, EDUCTION, or KIDS)
35
Macro Menu
Menu
Item
Description page
KEY Create a Macro to perform a sequence of
actions. 29
TIMR Start one of the eight timers to perform
either a regular action (Weekly, daily) or a
delayed action on a specific date.
33
Quic CH Add channels to a Quick Channel to make
cycling through a particular type of
television programming easier. (Example:
NEWS, SPORTS, MOVIES, EDUCATION, or
KIDS.)
36

13
Chapter 3-Setting Up the SRC-93 SERIES to
Control a Device
Before the SRC-93 SERIES can be used to control a
device, it needs to be configured to display your
existing remote control buttons and also programmed
to send the correct infrared signals.
This chapter guides you through the Touch Screen
layout and SRC-93 SERIES setup procedure.
Choosing a Device
The first step is to choose a device to setup. This could
be a new TV, DVD, or VCR etc… You will give this
specific device a name (label) on the SRC-93 SERIES.
There are two ways to do this based on what starting
point you want to work from:
•Create new Device: Use this method for a totally new
device.
•Modify Existing Device: Use this if you are having a
problem with an already setup device and want to
make a change or enhancement.
Creating a New Device
To create a new device, follow these steps:
Press and hold the SETUP button on the
Touch Screen.
Press each number button (2, 4, 6, 8) until it
disappears.
Use the arrow buttons on the Touch Screen
to select NEW and then press the OK button.

SRC-93 SERIES User’s Manual
14
1. Press the device key you wish to
use for this device. For example, if
this is a new TV you should press
the TV button. For a new DVD
player, press the DVD button.
2. Give your new Device a label.
Use the UP and DOWN arrows to
change the letter. Use the LEFT
and RIGHT arrows to change the
position. (Labels can be four digits
long.)
Press the OK button.
3. Select one device attribute to
load the default device screen.
Use the UP and DOWN arrows to
choose.
4. Press the OK button to confirm.
Modifying an Existing Device
If you want to modify an existing device that is already
setup in the SRC-93 SERIES, no additional preparation is
required and you may proceed directly to the Touch
Screen layout changing section on page 15.
Re-Labeling Devices
You may want to re-label an old device and you can
do this using the LABL selection in the SETUP Menu:

15
1. Use the device keys to select the
device you want to label.
2. Use the arrow keys to give the device
a new label.
3. Press OK when finished.
Then press EXIT to leave the SETUP
menu.
Changing Touch Screen Layout
The layout edit mode enables you to customize the
SRC-93 SERIES's Touch Screen display to match your
existing remote controls. The following steps show you
how to make the display on the SRC-93 SERIES
correspond to an existing remote.
Use the LAY selection in the SETUP Menu:
Press and hold the SETUP button on the
Touch Screen.
Press each number button (2, 4, 6, 8)
until it disappears.
Use the arrow buttons on the Touch
Screen to select LAY and then press
the OK button.

SRC-93 SERIES User’s Manual
16
1. Press the device keys to select
the device you want to modify.
(ex. Press TV button)
Press the button (Page Button) to
change to the Touch Screen page you
want to modify.
Press the button to show all
available LCD choices for all buttons.
Press the Power
button to show all possible
LCD choices.
2. Touch the button that you wish to
change.
(You may change as many buttons as
you wish.)
3. Each time you touch the button
its appearance will change.
4. Press OK to confirm your changes.
Then press EXIT to leave the SETUP
Menu.
Programming Infrared Codes
There are two methods you can use to program infrared
codes into the SRC-93 SERIES:
•Using Manufacturer Codes: Use this method to automatically