Super Circuits PC88WR Installation manual

BULLET BLACK & WHITE CCD CAMERA
OPERATION MANUAL
KEY FEATURES
Thank you for choosing our high quality camera. Before attempting to connect or operate,
please read and follow these instructions.
These CCD video cameras employ a SONY 1/3” CCD solid-state imaging device which provide superior
performance. These cameras can be easily in mostly indoor locations along with its very low current consumption
of 80mA or less. These cameras are not only easy to install but achieve an excellent reliability record.
ACCESSORIES FURNISHED
SPECIFICATIONS
Accessories DIY cable Mounting Bracket Screw Manual
Q'ty - 1 3 1
Option 1 - - -
Face Plate : Point at the CCD without obstruction of light from any other material.
Signal Format EIA CCIR EIA CCIR
Image Device
1/3" Sony Super HAD CCD
1/3" Sony Exview HAD CCD
Scanning Frequency
H:15.734[KHz], V:59.94[Hz] H:15.625[KHz], V:50[Hz]
Total Pixels
537(H) x 505(V) 537(H) x 597(V) 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 510(H)x492(H) 500(H)x582(H) 811(H)x508(H) 795(H)x596(H)
Scanning System 2 : 1 Interlace
H.Resolution 420TV Lines 600TV Lines
S/N Ratio More than 50dB(AGC Off)
Gamma γ=0.45
Electronic Shutter 1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec 1/60 ~ 1/100,000sec 1/50 ~ 1/100,000sec
Min.Illumination
0.5 [email protected]/30IRE
Exview 0.0003Lux/FacePlate
0.1 [email protected]/30IRE
Exview 0.003Lux/FacePlate
Gamma γ=0.45
Video Output Composite 1[Vp-p] 75[Ω] unbalanced
Operating Temperature -10℃~ +50℃
Storage Temperature -20℃~ +60℃
Power Consumption DC 12V (±10%) 80mA or Less
Option 19Φ(mm), 23Φ(mm)
Lens Option Board Lens, Pinhole Lens, Door View Lens, Varifocal Lens

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasnoable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio communications.
However, there is no guarantree that interference will not occur in a particular installation. If this
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Not e -
• Reorient or relocate the receiving antena.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
whice the receiver is connected.
• Consult the dealer or an experienced radio / tv technician for helf.
Any changes or modifications in construction of this devies which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Caution -
1. A regulated DC12V 300mA power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassmble the camera to gain access to the internal conponets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
DIMENSIONS
CAMERA MOUNTING POSITION
Unit : mm
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
CONNECTION
54.4
45 45
37
40.8 50.5
Mounting Hole
(1/4"-20UNC)
Mounting Hole
(1/4"-20UNC)
Mounting Hole
(1/4"-20UNC)
Mounting Hole
(1/4"-20UNC)
Mounting Hole
(1/4"-20UNC)
Φ19
Φ19 Φ19
Φ19 Φ19
110 75.5
130 95 Φ32.4
Φ23
Φ26
Φ37
111
Mounting Hole
(1/4"-20UNC)
Φ60
37~70
500 or 700
Mounting Hole
(1/4"-20UNC)
40
28.6
24.8
97
3 - Φ3.2