Secura QLL22 User manual

QLL 22 INSTRUCTION MANUAL
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520 We’re ready to help!
Scan for easy install video
san.us/1146

2
100 lbs.
(45.3 kg)
Wood Stud Install
Concrete Install
Tape
Measure Pencil Level Screw driver
Electric
Drill
Socket
Wrench
Stud
Finder Awl Wood Drill Bit
Masonry
Drill Bit Hammer
3/8 in.
(10 mm)
1/2 in.
(13 mm) 7/32 in.
(5.5 mm)
CAUTION: IMPORTANT SAFETY INSTRUCTIONS —PLEASE READ ENTIRE MANUAL PRIOR TO USE —SAVE THESE INSTRUCTIONS
Before getting started, let’s make sure this mount is perfect for you!
Does your TV
(including accessories)
weigh MORE than
100 lbs. (45.3 kg)?
No?Perfect – you may continue.
Yes?This mount is NOT compatible.
Visit secura-av.com or call 1-800-359-5520
(UK: 0800 056 2853) to find a compatible mount.
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use
of this product, contact Customer Service at 1-800-359-5520 (UK: 0800 056 2853).
Do you have
all the tools
needed?
1
2
3
4
What is your
wall made of?
Ready to begin?
Solid concrete or
concrete block?
Perfect!
Drywall with
wood studs?
Perfect!
CAUTION:
DO NOT
install into
drywall alone
Unsure?
Call Customer Service:
1-800-359-5520
(UK: 0800 056 2853)
?
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
CAUTION: Avoid potential personal injury or property damage!
●This product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

3
200mm
7.87in
200mm
7.87in
400mm
15.75in
600mm
23.62in
650mm
25.59in
65.5mm
2.58in
100mm
3.94in
500mm
19.69in
400mm
15.75in
600mm
23.62in
300mm
11.81in
200mm
7.87in
432.4mm
17.03in
75.5mm
2.97in
32mm
1.26in
TV INTERFACE
WALL PLATE
FULLY ASSEMBLED MOUNT TOP VIEW - RETRACTED
SIDE VIEW - RETRACTED
Dimensions

4
M6/M8
M6 x 12mm M6 x 35mm
M8 x 16mm M8 x 35mm
M8 x 20mm
Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts
are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
22mm
TV Brackets
TV Stando
TV Screws
Washers
Spacers
03 x4
07 x4
04 x4
06 x4 08 x4
05 x4 09 x4
01 x2
02 x2

5
Parts and Hardware for STEP 2
5/16 x 2¾ in. 5/16 in.
Fischer UX 10 x 60R Anchor
F
ischer UX 10 x 60R Anchor
Fischer UX 10 x 60R
Concrete Anchors
For concrete installations ONLY
CAUTION: Do not use in drywall or wood
Lag Bolts
Washers
Wall Plate
11 x2 12 x2
13 x2
10 x1

6
STEP 1 Attach Brackets to TV
FLAT BACK ROUND BACK CABLESINSET HOLES
1.1 Select TV Screw Diameter 1.2 Select TV Screw Length
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M6, or M8) to use.
ab
If your TV has a flat back AND you want your TV closer to
the wall, use the shorter screws (a).
Use the spacers and longer screws (b) to accommodate:
●Round/irregular back TVs
●TVs with inset mounting holes
●Extra space needed for cables
M6 M8
Too Short
Too Long
Correct
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
contact Customer Service
at 1-800-359-5520.
CAUTION:
Verify adequate thread
engagement with your screw/
washer/spacer combination AND
TV bracket.
-Too short will not hold the TV.
-Too long will damage the TV.

7
1.3 Attach TV Brackets
aFlat Back bRound Back / Extra Space
IMPORTANT: After
attaching the brackets, adjust
the straps so they are level
with the bottom of the TV.
aFlat Back bRound Back / Extra Space
Install TV brackets 01 and TV standos 02 onto your TV as shown, using the TV screw/washer/spacer configuration you selected for your TV.
CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws only enough
to secure the TV bracket to the TV. DO NOT overtighten the screws.
IMPORTANT: Ensure TV bracket is securely fastened before moving on to the next step.
08
08
08
08
09
09
01
02
03
03
04
04
06
06
05
05
07
07
02 02
01 01

8
1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using an awl, a thin nail, or an edge to edge stud finder.
2. Position the wall plate 10 at your desired height and line up the holes with your stud center line and level the wall plate 10 and mark the holes.
21
Max.
5/8 in. (16 mm)
STEP 2A Attach Wall Plate to Wall Wood Stud Option
CAUTION: DO NOT use the lower slots for
installation, only use the upper slots as shown
10
16 –24 in.
(406 –610 mm)
UP
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1 ½ x 3 ½ in. (38 x 89 mm)
●Minimum horizontal space between fasteners: 16 in. (406 mm)
●DO NOT use the lower slots for installation, only use the upper slots as shown

9
4
3
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2¾ in. (70 mm). Be sure to drill into the center of the studs.
4. Install wall plate 10 using two lag bolts 11 and two washers 12 . Tighten the lag bolts only until the washers are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
CAUTION: Avoid potential personal injury or property damage! All lag bolts MUST BE firmly tightened to prevent unwanted movement of
the wall plate 10 .Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Go to STEP 3 on PAGE 12.
CAUTION: DO NOT use the lower slots for
installation, only use the upper slots as shown
7/32 in.
(5.5 mm)
2¾in. (70 mm)
10
11 12
UP

10
1. Position the wall plate 10 on the wall at your desired height. Level the wall plate 10 and mark the hole locations.
2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75 mm). Never drill into the mortar between blocks.
21
STEP 2B Attach Wall Plate to Wall Solid Concrete or Concrete Block Option
CAUTION: DO NOT use the lower slots for
installation, only use the upper slots as shown
3/8 in.
(10 mm)
3 in. (75 mm)
10
UP
CAUTION: Avoid potential personal injury or property damage!
●Mount the wall plate assembly 10 directly onto the concrete surface
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 16 in. (406 mm)
●DO NOT use the lower slots for installation, only use the upper slots as shown

11
43
3. Insert two anchors 13 .
CAUTION: Be sure the anchors are seated flush with the concrete surface.
4. Install wall plate 10 using two lag bolts 11 and washers 12 . Tighten the lag bolts only until they are pulled firmly against the wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts.
CAUTION: DO NOT use the lower slots for
installation, only use the upper slots as shown
10
11
12
13
UP

12
STEP 3 Attach TV to Wall Plate
HEAVY! You may need
assistance with this step.
Hang the TV/Bracket assembly onto the wall plate 10 .
IMPORTANT: You will hear an audible click when the TV
brackets are securely fastened to the wall plate.
10
01
10
01

13
Adjustments
HEAVY! You may need
assistance with this step.
To remove the TV from the wall plate:
1. Disconnect all cables from the TV.
2. Pull down and hold the release straps, while pulling the bottom of the TV away from the wall.
3. Lift the TV up and o of wall plate 10 .
10

14

15

Milestone AV Technologies • 6436 City West Parkway • Eden Prairie, MN 55344 USA 6901-002593 00
Milestone AV Technologies and its aliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However,
Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in
connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy,
completeness or suciency of the information contained in this document.
©2016 Milestone AV Technologies. All rights reserved. Secura is a brand of Milestone.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
Thank you for choosing Secura! Please take a moment to let us know how we did:
Call us: 1-800-359-5520
UK: 0800 056 2853
Email us: [e-mail]