SVT innovations SVT-2 Series User manual

SVT-2 Outdoor Station B
User Manual
SVT-2 Outdoor Station B
2W12120
Please read this user manual prior to installing the system, and keep it well for future use.
Dan Smith

CONTENTS
1.Parts and Functions............................................................................................. 1
2.Terminal Descriptions .......................................................................................... 1
3.Specification ...................................................................................................... 2
4.Mounting .............................................................................................................. 2
4.1 Mounting Without Rain Guard ....................................................................... 2
4.2 Mounting With Rain Guard ............................................................................ 3
4.3 External Motion Detection............................................................................. 4
5.System Wiring and Connections ......................................................................... 4
5.1 Basic Connection........................................................................................... 4
5.2 Electric Lock Connection ............................................................................... 5
5.2.1 Door Lock Controlled with Internal Power ............................................ 5
5.2.2 Door Lock Controlled with Dry Contact ................................................ 5
5.3 Multi Outdoor Stations Connection ............................................................... 6
5.4 Multi Indoor Monitors Connection .................................................................. 7
5.4.1 Basic IN-OUT Wiring Mode ................................................................. 7
5.4.2 With DBC-4 Wiring Mode .................................................................... 8
6.Setup Instructions ........................................................................................... 9 - 14
6.3 Power Supply................................................................................................. 15
7.Cable Requirements ............................................................................................ 16

-1-
1.Parts and Functions
2.Terminal Descriptions
BUS
PL
S1+ S2+ S-
1 2
3
Lock Control
Jumper
PIR Motion
Detector Connect
Port
+12 V
GN D
PI R
L1L2
PL
S+S-
Main Connect
Port
[11] [10]
[9]
[1]
[3]
[4]
[8]
[7]
[6]
[5]
[12]
[13]
[2]
[1] Microphone
[2] UNLOCK indicator
[3] CALL indicator
[4] Call button
[5] Nameplate
[6] Front panel
[7] Speaker
[8] Night view LED
[9] Camera lens
[10] Rain cover
[11] Mounting hook
[12] Connection port
[13] Screw hole

-2-
3.Specification
4.Mounting
4.1 Mounting Without Rain Guard
145 - 165 cm
1
2
1 2 3 4
Lock Control Jumper: To select the lock type.
Motion Detector Connect Port: To connect external PIR motion detector.
Main Connect Port: To connect the bus line and the electronic locks.
•L1,L2: Connect to the bus line, no polarity.
•PL: External lock power input, connect to the power positive(power +).
•S+: Lock power(+) output.
•S-: Lock power(-) output, connect to the power(-) input of locks(only when using the door
station to power the locks, if using the external power supply for the locks, the S- will not be
connected).
Power supply: Power
consumption:
Camera lens:
Lock Power supply:
Number of relay circuits:
Mounting:
Working temperature:
Protection:
Material:
Wiring:
Dimension:
DC 24V
Standby 0.8W; Working 3W
Color CMOS, 520TVL
1/4" camera, 115º wide angle
12Vdc, 280mA(Internal Power);
2(the second lock need external power to support)
Surface wall-mount
-4ºF ~ +131ºF | -20ºC ~ +55ºC
IP54
Zinc alloy panel
2 wires, non-polarity
176(H)×90(W)×27(D)mm(surface mounted)

-3-
4.2 Mounting With Rain Guard
12
Rainy cover
Rainy cover
The distance between
the top of main unit
and rain cover should
be not less than 3mm.
Main unit
Main unit
3 4 5
AcDbMLeader (ACDB_MLEADER_CLASS)
AcDbMLeader (ACDB_MLEADER_CLASS)
1.. Connect the cable correctly .
2.. Dr l holes in the wall to match the size of screw stoppers,then attach the rainy cover and
main unit to the wall, and the distance between the top of main unit and rain cover should be not
less than 3mm.
3.. Install the name plat
4. Attach the front panel to the main unit.
5.. Use the special screwdriver and the screws to fix the pan

-4-
4.3 External Motion Detection
5.1 Basic Connection
5.System Wiring and Connections
The door station is equipped with a terminal to
connect external motion detector.
If the external motion detector is connected
to the system,following functions will be effec-
tive:
If detect someone passing by, the door station
can be activated operation to unlock or turn
on light.
12V
Motion
detector
GND
PIR
BUS(IM) BUS(DS)
-
+
L1 L2 PL S+ S-
ID=0
1 2 3 4 5 6
ON DIP
L2
L1
DIP Switches
SVT-2 PC6
AC~
100~240VAC

-5-
5.2 Electric Lock Connection
5.2.1 Door Lock Controlled with Internal Power
5.2.2 Door Lock Controlled with Dry Contact
1.Electronic lock of Power-on-to-unlock
type should be used.
2.The door lock is limited to 12V, and hold-
ing current must be less than 250mA.
3.The jumper should be placed on position
2 and 3 before connecting.
4.The door lock control is not timed from
Exit Button(EB).
5.The Unlock Mode must be set to 0 (by
default).
EB
*
LOCK
Jumper position on 2&3
1 2 3
L1 L2 PL S+ S-
1.The external power supply must be used according to the lock.
2.The inside relay contact is restricted to
230Vac 1A or 24Vdc 1A.
3.The jumper must be taken off before
connecting.
4.Setup the Unlock Mode according to
different lock types.
•Power-on-to-unlock type:Unlock
Mode=0 (by default)
•Power-off-to-unlock type:Unlock
Mode=1
Take off the jumper
1 2 3
L1 L2 PL S+ S-
LOCK
POWER
SUPPLY
*A SVT-2 RCL lock connector is needed for 2nd lock connection.

-6-
5.3 Multiple Outdoor Stations Connection
100~240VAC
SVT-2 DBC4
A B C D
OFF
ON
Impedance
switch
BUS(IM) BUS(DS)
SVT-2 PC6
AC~
ID=0
1st door station
ID=1
2nd door station
ID=2
3rd door station
ID=3
4th door station
L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S- L1 L2 PL S+ S-
To monitors
•Max.4 outdoor stations can be connected to the system.
•Ensure to set the correct address for each outdoor station. Refer to Page X for more details
about the address setting of outdoor stations.

-7-
5.4.1 Basic IN-OUT Wiring Mode
5.4 Multiple Indoor Monitors Connection
ID=0
Optional modules
BUS(IM) BUS(DS)
SVT-2 PC6
AC~
100~240VAC
SCU TPS

-8-
5.4.2 Using SVT-2 DBC-4 distributor device - Wiring Mode
DBC4A1
A B C D
SVT-2 RCL SVT-2 DBC4
Impedance
OFF ON
switch
Code=1 Code=2
Code=3 Code=4
ID=0
Optional modules
SVT-2 BDU
85~260AC
SVT-2
DPS
SVT-2
PS5