Swann SB-1248 User manual

Bench Seat
SB-1248
Register your warranty at www.swanstone.com.
Product Warnings
Safety Guidelines
Kit Contents
Required Tools
Preparation Tips
Installation Procedure
Cleaning & Maintenance
Surface Repair
Warranty Information
Read and Understand
Before Installing
Form # 191-02-10

800-325-7008 3 The Swan Corporation – Swanstone
The Swanstone Assurance — if our product is
properly installed and maintained, as stated in these
instructions, it will not leak.
R
Re em me em mb be er r
–
–
S
Sa af fe et ty y
F
Fi ir rs st t
The Swan Corporation, the makers of the Swanstone Wall
Systems and Panels, cannot anticipate every possible
circumstance that might involve a potential hazard during
the installation of our product(s). The warnings and
instructions in this installation guide are, therefore, not
all-inclusive. If a tool, installation procedure, or work
method that is not specifically recommended by the Swan
Corporation is used, you must satisfy yourself that it is
safe. You should also make sure that the Swanstone
product(s) will not be damaged by the methods you
choose. The Swan Corporation will not be held
responsible for water damage of any kind in connection
with the installation of one of our Swanstone
bath/shower/panel kits.
To avoid product damage, personal injury, or even possible
death, carefully read, understand, and follow all the
instructions in this installation guide before installing this
product(s). Do not use cleaning fluids or operate power
tools unless you read and understand the instructions and
warnings in this and all other applicable labels or manuals.
Proper use of tools and the products described in this
guide is your responsibility.
WARRANTY
This product is covered by a Limited Lifetime Warranty.
Refer to the Warranty section in this manual for complete
details.
SSaavvee
tthhiiss mmaannuuaall ffoorr ffuuttuurree rreeffeerreennccee..
Important information on cleaning, maintenance, and
repair is contained within.
WARNING
IMPORTANT NOTICE

IMPORTANT NOTICE: Indicates that equipment or
property damage can result if instructions are not
followed.
Read and Understand the Manual
It is the responsibility of any individual who
installs or maintains this product to fully
understand and follow proper installation and
maintenance procedures. Be aware of the inherent
dangers in the use of power tools when installing this
product. Read and understand all Warnings, Cautions,
and Important Notices in this manual.
Work Safely
DO NOT proceed if any doubt arises about the
correct or safe method of performing anything
found in this or other Swanstone manuals.
The installation of this product can require using power
tools. Do not use power tools without adequate training.
If necessary, hire or consult a trained professional for
expert assistance before continuing.
Use Proper Tools
Always use proper tools which are in good,
working condition during the installation of the
Swanstone products. Using tools other than
those listed could adversely affect the integrity of floors,
pipes, walls, or this product and could result in water
damage or other damage to floors, pipes, walls, or other
portions of your building or home.
Do Not Use Nails
Do not use nails to secure the bench seat
panel to the framing. The panel is mounted
with clear silicone only. Only use the supplied
or recommended clear silicone to attach this product.
Never use hammers, nails, or screws which could
adversely affect the integrity of this product. Nails and
screws could puncture the Swanstone Wall Systems and
Panels, resulting in water or other damage to floors,
pipes, walls, or other portions of your building or home.
Inspect Before Cutting
Make sure no electrical wiring or plumbing is
present before cutting into a wall.
Wall Conditions
Inspect the mounting surface before installing
the panel. Never install the panel over damp
material or an existing mold condition.
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against
unsafe practices.
Use Proper Installation Methods
Follow all instructions related to wall surface
preparation. Failure to follow such instructions
could cause the panels to detach from the wall
surface after installation, resulting in personal injury.
Failure to follow these instructions could result in water
damage.
Slipping Hazard
Do not install this product in the presence of
water. Installing this product without drying all
surfaces, or in the presence of water, could
cause you to slip and fall due to wet floors or spilled
fluids. Personal injury can result from slips or falls.
Before installation, dry all surfaces, including the floor,
with a cloth or paper towel. Clean up all water or spilled
fluids immediately.
Tripping Hazard
Personal injury can result from tripping over
power cords, tools, or other items. DO NOT
leave items laying around the work area.
Personal Protection
Be sure to use all personal protective
equipment, such as sturdy work
boots, preferably with steel toes,
gloves, and hard hat, if necessary, to ensure your own
safety. To prevent possible damage to your hearing,
always wear ear protection, such as earmuffs or
earplugs, when working around power tools.
Cutting Hazard
The installation of the Swanstone product may
require using power tools. Keep hands away
from the cutting edge of any tool used in the
installation of our product. Placing fingers in or around
the cutting blades could result in serious personal injury.
Sharp Edge Hazard
After cutting the edge of a Swanstone panel, it
can be sharp. Wear protective gloves to
prevent personal injury.
CAUTION
IMPORTANT NOTICE
The Swan Corporation – Swanstone 4 800-325-7008
Safety Guidelines

Room Temperature
Allow the Swanstone panel and
silicone to adjust to room
temperature for at least six hours
before installation. The panel should be installed at
temperatures not less than 65 degrees. Panels should
not be installed in areas where the temperature may
drop below freezing (32°F). Failure to follow this
recommendation could adversely affect the silicone
which holds the panels to the mounting surface.
WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in serious
injury or death.
Eye Protection
Be sure to use all personal protective
equipment to ensure your own safety. To
avoid eye injury, always wear protective
glasses with side shields when using power tools. Also,
make sure no one else can be injured by flying particles
when using power tools.
Fire Hazard
Personal injury or death can
result from a fire caused by
flammable liquids or
silicone. Cleaners or solvents can be highly explosive,
resulting in personal injury or even death, when not used
properly. Clean up any flammable substance
immediately. Sparks or open flames can cause
flammable substances to ignite. DO NOT smoke while
working on or near any flammable substance.
Solvents Hazard
Follow all manufacturer’s safety instructions
for silicone and denatured alcohol. Alcohol
vapors are both flammable and hazardous to
breathe. Silicone vapors may irritate eyes and nose.
Personal injury can result from improperly handling or
use of products such as denatured alcohol. Always
follow the manufacturers recommendations for the safe
use of these products. Ventilate any work area before
beginning to apply silicone, cleaning agents, or solvents.
Fumes Hazard
The fumes from the silicone and
solvents used by the installer can be
harmful if used in an unventilated
room. Always work in a well-ventilated area.
Dust Hazard
When cutting or drilling the
Swanstone product, use a dust
collection method which prevents
dust particles from going into the air. Always work in a
well-ventilated area. Always use an OSHA approved
dust mask when cutting, drilling, or sanding Swanstone
products.
Power Tool Hazard
To prevent personal injury or possible
death, always follow the electrical
safety recommendations of the
power tool’s manufacturer. Do not use power tools in an
unsafe manner. Power tools should only be connected
to a circuit protected by a ground-fault circuit interrupter
(GFI).
Shock Hazard
Never use electric power tools
around water, condensation, or other
liquids. Electric shock can cause
severe burns, significant injuries, and even death. If an
extension cord is required, always use an OSHA
approved extension cord. Power cords should only be
connected to a circuit protected by a ground-fault circuit
interrupter (GFI).
Electrical Shock Hazard
Contacting live electrical wiring with
power tools or hand tools can cause
serious injury or death. Make sure
all related circuit breakers are turned OFF. Test for live
circuits or wiring inside any wall where installation of the
Swanstone product requires cutting into a wall.
Electrocution Hazard
Water and other liquids conduct
electric current and can create a
short circuit, resulting in injury or
death. Keep all liquids away from electrical cords and
power tools. DO NOT create a short circuit between a
source of electricity and a liquid by being in contact with
both simultaneously.
WARNING
800-325-7008 5 The Swan Corporation – Swanstone
Safety Guidelines