Swegon REACT V BMPa User manual

The document was originally written in Swedish
Symbol key
Symbols on the machine
This product complies with
applicable EU directives
Symbols in this user manual
Warning/Caution!
Risk of crushing
Other risks
When the product is voltage fed, the damper will either
open or close. This can entail a certain risk of pinch
injuries to the fingers, for example, if these are placed
between the damper blade and ventilation duct when
the damper blade is rotating. The product’s actuator
is equipped with a release button that permits manual
control of the damper blade, always ensure this is activated
before working on the internal parts of the damper.
Handling
• Always use appropriate transport and lifting devices when the
product is to be handled to reduce ergonomic loads.
• The product must be handled with care.
• It is not permissible to carry the product by the measuring
tube.
Installation
• Moist, cold and aggressive environments must be avoided.
• Avoid installing the product near a heat source.
• Assemble the product according to applicable industry
regulations.
• Install the product so that it is not accessible by unauthorized
persons, for example above a suspended ceiling.
• Install the product for easy access during service/maintenance.
• Supplement the duct system with a cleaning hatch in the
vicinity of the product to facilitate cleaning.
• If the product is mounted above a fixed ceiling, the inspection
hatch must be located so that the product is accessible for
inspection.
• If the product is mounted so that it is possible to gain access
to the inside of the product, it must be supplemented with
appropriate protection, for example, a ventilation unit.
• If the product is mounted in cold areas, the whole product
must be insulated on the outside against condensation.
• For installation, the accessory FSR is recommended.
• The product can be installed position independent.
• It is recommended that the product be installed so that the
front is visible.
• The product must be laid down prior to installation so that it
cannot fall over.
• Check to make sure that the product does not have any
visible defects.
• Make sure that the product is properly secured after it has
been installed.
• Use the product’s eyes to secure the cables with cable ties.
• Make sure all cables are properly secured after installation.
• Check that the actuator/controller is properly mounted.
Application area
The product is a variable flow damper or constant flow damper
designed for comfort ventilation indoors. The product is used to
regulate the supply air or extract air flow in ventilation ducts.
The product may not be used for anything other than its intended
use.
General
Read through the entire instructions for use before you
install/use the product and save the instructions for
future reference. It is not permissible to make changes
or modify this product other than those specified in this
document.
The packaging contains the following items
1 x REACT V BMP
1 x Instructions for use
Protective equipment
Always use appropriate personal protective equipment
for the work in question, in the form of gloves, respirators
and protective glasses during handling, installation,
cleaning and service/maintenance.
Electrical safety
Permitted voltage, see “Electrical data”. It is not
permissible to insert foreign objects into the product’s
contactor connections or the electronics’s ventilation
openings; risk for short circuiting.
24 V isolation transformer to be connected should comply with
the provisions of IEC 61558-1.
Cable sizing must be carried out for cabling between the product
and the power supply source.
Disconnect the power supply when working on products that
are not required to run in production.
Always follow the local/national rules for who shall be permitted
to carry out this type of electrical installation.
REACT V BMPa
Instructions for Use 20230929
Art. 1546132

REACT V BMP
2Swegon reserves the right to alter specications. 20230929
Figure 1. Dimensions (mm), REACT V BMP circular. The damper can be installed at an optional angle.
25
C
EE
A
d Ø
100
3
6
0
°
Installation, torque, dimensions and weights
Circular design
Dimensions
Size Ød
(mm)
A
(mm)
B
(mm)
C
(mm)
E
(mm)
Torque
(Nm)
Weight
(kg)
Flow range Tolerance Q*±5%
with at least ±x
Min. Max = Vnom*)
l/s m3/h cfm l/s m3/h cfm l/s m3/h cfm
100 475 485 190 50 51.6 518 11 58 209 123 274
125 475 485 215 50 51.8 932 19 97 349 206 274
160 475 485 255 50 52.1 16 58 34 170 612 360 274
200 475 485 300 50 52.7 25 90 53 272 979 576 311 6
250 525 535 350 50 53.4 40 144 85 438 1577 928 518 11
315 560 570 415 50 10 4.8 63 227 133 710 2556 1504 829 17
400 695 705 505 60 10 6.8 102 367 216 1155 4158 2447 13 47 28
500 820 840 605 60 10 9.4 164 590 347 1850 6660 3920 20 72 42
630 915 935 735 60 20 14.4 300 1080 636 2920 10512 6187 32 115 68
*)Vnom at 120 Pa in pressure reading.
*Installed according to the instructions.

3
REACT V BMP
20230929 Swegon reserves the right to alter specications.
Figure 3. Straight duct section requirements 3 x Ø in case of
sound attenuator with baffle or centre body.
Installation
• The product’s air flow measurement requires a straight
duct section as per the installation figures.
• In unfavourable conditions before or with disruption,
the product’s tolerances cannot be guaranteed.
• Installation is position independent.
• The product can be installed horizontally or vertically.
• Instructions for Use are supplied with the product on
delivery, but can also be downloaded from www.
swegon.com.
Figure 4. Installation in the duct system. The ducts must be firmly
fixed to the frame of the building on each side of the product.
B
Figure 2. Straight duct section requirements in circular ducts,
number of Ø before product:
Image 1-5 require no straight duct section (image 3*illustrates
a T piece with a cleaning hatch).
Image 6 requires a straight duct section before the damper
equivalent to 4 x the diameter of the duct.
1.
2.
3*.
4.
5.
6.
B
Sound attenuator
with baffle
Clamp
Clamp
Damper
Damper
Straight duct section requirements Straight duct section requirements in case of sound
attenuator with baffle
Installation in the duct system

REACT V BMP
4Swegon reserves the right to alter specications. 20230929
Rectangular design
Dimensions
Size BxH
(mm)
Torque
(Nm)
Weight
(kg)
Flow range Tolerance Q*±5%
with at least ±x
Min. Max = Vnom*)
l/s m3/h cfm l/s m3/h cfm l/s m3/h cfm
200 x 200 57.2 67 241 142 365 1314 773 829 17
300 x 200 5 8.4 100 360 212 548 1973 1161 12 43 25
400 x 200 5 9.9 133 479 282 730 2628 1547 17 61 36
500 x 200 5 11.4 167 601 354 913 3287 1934 21 76 44
600 x 200 5 12.9 200 720 424 1095 3942 2320 25 90 53
700 x 200 5 14.4 233 839 494 1278 4601 2708 29 104 61
800 x 200 5 15.4 267 961 566 1460 5256 3093 33 119 70
1000 x 200 10 18.7 333 119 9 706 1825 6570 3867 42 151 89
300 x 300 5 10.9 152 547 322 834 3002 1767 19 68 40
400 x 300 5 12.4 203 731 430 1112 4003 2356 25 90 53
500 x 300 5 13.9 254 914 538 1390 5004 2945 32 115 68
600 x 300 5 15.4 305 1098 646 1668 6005 3534 38 137 81
700 x 300 10 17.1 355 1278 752 1946 7006 4123 44 158 93
800 x 300 10 18.7 406 1462 860 2224 8006 4712 51 184 108
1000 x 300 10 21.7 508 1829 1076 2780 10008 5890 63 227 133
400 x 400 5 14.0 273 983 578 1495 5382 3168 34 122 72
500 x 400 10 16.3 341 1228 723 1869 6728 3960 43 155 91
600 x 400 10 17.7 409 1472 867 2243 8075 4752 51 184 108
700 x 400 10 19.9 478 1721 1013 2616 9418 5543 60 216 127
800 x 400 10 21.4 546 1966 1157 2990 10764 6335 68 245 144
1000 x 400 10 24.5 682 2455 1445 3738 13457 7920 85 306 180
1200 x 400 20 27.6 819 2948 1735 4485 16146 9503 102 367 216
1400 x 400 20 30.7 955 3438 2023 5233 18839 11088 119 428 252
1600 x 400 20 33.7 1092 3931 2314 5980 21528 12670 136 490 288
500 x 500 10 18.8 429 1544 909 2347 8449 4973 54 194 114
600 x 500 10 20.8 514 1850 1089 2816 10138 5967 64 230 136
700 x 500 10 22.9 600 2160 1271 3286 11830 6962 75 270 159
800 x 500 10 24.9 686 2470 1453 3755 13518 7956 86 310 182
1000 x 500 20 29.0 857 3085 1816 4694 16898 9946 107 385 227
1200 x 500 20 33.1 1028 3701 2178 5633 20279 11935 129 464 273
1400 x 500 20 37.2 1200 4320 2543 6572 23659 13925 150 540 318
1600 x 500 20 41.2 1371 4936 2905 7510 27036 15912 171 616 362
600 x 600 10 23.0 618 2225 1309 3388 12197 7178 77 277 163
700 x 600 10 25.1 722 2599 1530 3952 14227 8373 90 324 191
800 x 600 20 27. 2 825 2970 1748 4517 16261 9571 103 371 218
1000 x 600 20 31.3 1031 3712 2184 5646 20326 11963 129 464 273
1200 x 600 20 35.4 1237 4453 2621 6775 24390 14355 155 558 328
1400 x 600 20 39.6 1443 5195 3057 7904 28454 16747 180 648 381
1600 x 600 20 43.8 1649 5936 3494 9033 32519 19139 206 742 436
700 x 700 20 28.0 844 3038 1788 4622 16639 9793 105 378 222
800 x 700 20 30.7 964 3470 2043 5282 19015 11192 121 436 256
1000 x 700 20 35.3 1205 4338 2553 6602 23767 13988 151 544 320
1200 x 700 20 41.0 1446 5206 3064 7923 28523 16787 181 652 384
1400 x 700 20 46.1 1688 6077 3577 9243 33275 19584 211 760 447
*)Vnom at 120 Pa in pressure reading.
*Installed according to the instructions.

5
REACT V BMP
20230929 Swegon reserves the right to alter specications.
20
20
H
220
250
20 20
B85
20
20
H
220
250
20 20B 85
Figure 5. Dimensions (mm), REACT V BMP rectangular.
Straight duct section requirements
Type of disruption E (m2=5%) E (m2=10%)
One 90° bend E = 3 x B E = 2 x B
T piece E = 3 x B E = 2 x B
Figure 6. Straight duct section requirements in rectangular ducts.
E = Straight duct section
B = Width of duct
H = Height of duct
Figure 7. Straight duct section requirements 3 x B in case of
sound attenuator with baffle. Applies to both supply and extract
air.
1
x
B
E
E
1xB
1xB
Sound attenuator
with baffle
Straight duct ≥3xB
Damper
Installation
• The product’s air flow measurement requires a straight
duct section as per the installation figures.
• In unfavourable conditions before or with disruption,
the product’s tolerances cannot be guaranteed.
• Damper spindles must be installed horizontally.
• For rectangular ducts, the damper is always installed so
that the controller/actuator is placed along the side of
the duct.
• Instructions for Use are supplied with the product on
delivery, but can also be downloaded from www.
swegon.com.
Straight duct section requirements in case of sound
attenuator with baffle

REACT V BMP
6Swegon reserves the right to alter specications. 20230929
2135
a
AC 24 V
DC 24 V
bc def
Y U
BK RD WH OG
-+
–+
21 3 5
– + MP
A)
Y U
BK RD WH OG
-+
Figure 8. Wiring diagram.
Figure 9. Wiring diagram MP-Bus.
Additional actuators and sensors (max. 8).
1-2 – Supply voltage 24 V AC/DC
1-3 – Control signal (Y) 0..10/(2..10) V DC
1-5 – Actual value signal (U) 0..10/(2..10) V DC
For further calculations of Y and U see the formulas on page 10.
Load on output 5: max 0.5 mA
Connections Regulation and forced control via
analogue control signal
See connection in the wiring diagram, Figure8.
a b c d e f
Signal
T
–
3 3
+
3 3 3 3
Mode 2...10 V Closed Vmin1Vmax Open2Closed 3Vmin
Mode 0...10 V Vmin Vmin1Vmax Open2Closed 3Vmin
1 Control signal 0-10 V DC / 2-10 V DC
2 Positive half-wave, only AC
3Negative half-wave, only AC
Mode 2-10 V: Closed damper < 0.1 V
˜ ˜ ˜

Handling R
7
REACT V BMP
20230929 Swegon reserves the right to alter specications.
Figure 10. Belimo actuator. Figure 11. ZIP-BT-NHC. Figure 13. NFC contact for smartphones.
Figure 12. Bluetooth contact for smartphones.
Pushbutton and LED lighting green
Off: No power or fault
On: In operation
Button press: Activates rotation angle adaptation
Pushbutton and LED lighting yellow
Off: Normal operation
On: Adaptation or synchronisation process is active
Flickering: MP communication activated
Flashing: Addressing request sent to MP client
Button press: Confirmation of addressing
Release button
Pressed button: The actuator is disengaged, the motor stops, manual overriding possible
Released button: Synchronisation starts, followed by standard mode
Service port
For connection of the hand-held terminal ZTH EU and PC-Tool
NFC logotype
For connection to Belimo Assistant App
Function LED colour Light pattern Meaning
ZIP-BT-NHC started up Green Flashes once Battery OK (>30%)
Green > red Flashes once Battery low, charging required
ZIP-BT-NHC is in operation Green Flashes every 5 seconds Standby mode
Blue Flashes once Bluetooth® connection established (pairing)
White Fixed Searching for NFC tag
White Flashing NFC connection active
Charging battery (ZIP-BT-NHC switched off) Green Flashing Battery being charged
Green Fixed Battery charged
NFC, Smartphone – Belimo Assistant App
Settings and diagnostics for the actuator can be carried out contactless via NFC. This requires an Android or iOS smartphone, the ZIP-BT-NFC
dongle for Bluetooth contact with smartphones without NFC, as well as Belimo Assistant App.
To find the reception range with ZIP-BT-NFC the NFC logotypen needs to be visible through the positioning port, see figure 12.
When using a smartphone with NFC contact the smartphone needs to be centered above the NFC logotype on the actuator, see figure 13.
ZIP-BT-NFC must be secured to the unit with the attachment belt to avoid injuries to users and damage to property.
ZTH EU / PC-Tool
Settings and diagnostics for the actuator can be carried out using Belimo PC-Tool or the hand-held terminal ZTH EU.
When using the PC-Tool software, ZTH EU (USB) acts as an interface converter.
1
2
3
4
5
Adaption
Status
Power
Address
1
2
3
5
4
Switch
Mounting attachment for
attachment belt Micro USB charging
socket
Positioning port
for NFC antenna
LED display

Settings for actuator
Display text Description
Identification of actuator
Serial number
Actuator type
Software version
Designation
Position
Shows the actual value
Shows the set point value
Shows the actual value
Shows Δp
Shows the actual value
Shows damper position
Shows the actual value
Forced control
Normal operation
Actuator stops in the current position
Damper regulates to selected max. value
Damper regulates to selected intermediate position
Damper regulates to selected min. value
Closes the damper fully
Opens the damper fully
Available in expert mode
Direction of rotation. Available in advanced mode.
Anti-clockwise (standard, may not be changed)
Clockwise
Factory reset
Available in expert and advanced mode
Adjusts to desired min. value
Min. value must be lower than the max. value
Adjusts to desired intermediate value
Available in expert mode
Adjusts to desired max. value
Max. value must be higher than the min. value
Shows the nominal air flow
Pressure on which nominal air flow is based
Available in expert mode
Number of metres above sea level
Available in advanced mode
Setting of MP address
MP USB
i
i
esc
esc
OK
OK
Language
>English
Figure14. ZTH EU – Hand-held terminal for setting and reading
the actuator’s parameters.
Browses up or down, and changes values/status
Confirms selected value/goes to selected sub menu
Cancels change/leaves the sub menu
Shows additional information, if available
MP USB
i
i
esc
esc
OK
OK
Settings for hand-held terminal ZTH EU
To access the settings, press and hold OK and power up the
hand-held terminal. Exit with esc.
Display text Description
Change of language
Change of unit
Activation of expert mode
Activation of advanced mode
Duration of background lighting
Clearing of the memory
REACT V BMP
8Swegon reserves the right to alter specications. 20230929

9
REACT V BMP
20230929 Swegon reserves the right to alter specications.
Cleaning
Ideally, the product should be cleaned in connection with
the cleaning of the rest of the ventilation system.
Cleaning of electrical components
• If needed, use a dry cloth to clean the components.
• Never use water, detergent and cleaning solvent or a
vacuum cleaner.
External cleaning
• If necessary use tepid water and a well-wrung cloth.
• Never use detergent and cleaning solvent or a vacuum
cleaner.
Internal cleaning
• When cleaning the ventilation system, the product
must be dismantled if there are no cleaning hatches
close to the product.
• Cleaning equipment such as whisks and the like must
not be fed through the product.
• If necessary remove dust and other particles that can
be present in the product.
• Never use detergent and cleaning solvent or a vacuum
cleaner.
Service/maintenance
• The product does not require any maintenance, except
for any cleaning when necessary.
• In connection with a service, mandatory ventilation
inspection or cleaning of the ventilation system, check
that the general condition of the product appears to be
good. Pay particular attention to the suspension, cables
and that they sit firmly in place.
• It is not permissible to open or repair electrical
components.
• If you suspect that the product or a component is
defective, please contact Swegon.
• A defective product or component must be replaced by
an original spare part from Swegon.
Materials and surface treatment
All sheet-metal parts are galvanized sheet steel (Z275).
Disposal
Waste must be handled according to local regulations.
Product warranty
The product warranty or service agreement will not be
valid/will not be extended if: (1) the product is repaired,
modified or changed, unless such repair, modification
or change has been approved by Swegon AB; or (2) the
serial number on the product has been made illegible or
is missing.
Trouble shooting
The product shows incorrect/no air flow
• Make sure that the product is energized.
• Check that the product’s set size corresponds with the
physical size.
• Make sure that the product is installed according to the
recommended distance to disruptions, see “Installation”.
• Check that there is an air flow.
• Make sure that the product is correctly oriented in terms
of air direction. The air flow must follow the instructions
on the product.
• Check that the measuring tube is mounted correctly,
plus to plus (red), minus to minus (blue).
• Check that the measuring tubes are undamaged and
not creased.
• Check with the help of the k-factor and pressure
difference between the red and blue measuring tubes
that the flow is within the product’s measurement
range.
The product does not regulate the air flow
• Make sure that the product is energized.
• Check that the damper motor has not become
detached from the damper spindle.
• Check that the damper motor works by pressing in the
motor’s release button, turn the damper spindle, release
the release knob and then see whether the damper
motor starts to move.
• Check that the product is connected correctly.
• Check that the product is not force controlled.
The product does not regulate on the desired air
flow
• Check that the settings for Vmin and Vmax correspond
with the required regulation range.
• Check the electrical connection for the required
function, see the wiring diagram in the document
“REACT Belimo Description of functions & wiring
diagram”.
• Check that the product is connected correctly, check
the “Y” signal and polarity on “G” and “G0”. See
“Connections”.

4,00 V
V DC
U
1 2 5
3
Y
Figure 15. Shows connection of a voltmeter to check the actual
value.
Performance checks
Formulas for calculating air flow
The following applies for analogue control.
Control signal 0..10 V DC give the following formulas:
• Calculation of the current pressure (Vact) when you know the
value of the control signal (Y):
Y
10 V DC
Vact = Vmin + (Vmax – Vmin)
Vact
Vnom
U = 10 V DC
Y – 2 V DC
8 V DC
Vact = Vmin + (Vmax – Vmin)
Control signal 2..10 V DC gives the following formulas:
• Calculation of the current flow (V
act
) when you know the
value of the the control signal (Y):
Vact
Vnom
U = 2 V DC + 8 V DC
• Calculation of the current actual value (U) when you know
the value of the current flow (Vact):
• Calculation of the current actual value (U) when you know
the value of the current flow (Vact):
Key to formulas opposite:
Y = control signal in [V] DC
U*= actual value signal in [V] DC, always refers to 0-Vnom.
Vact = current air flow in [l/s, m3/h]
Vmin = set min. flow in [l/s, m3/h]
Vmax = set max. flow in [l/s, m3/h]
Vnom = nominal flow in [l/s, m3/h], see tables on pages2 and 4.
*Note! Does not indicate damper position.
REACT V BMP
10 Swegon reserves the right to alter specications. 20230929

Replacing the damper motor
Figure 16. Dismantling the damper motor.
1. Disconnect the cable.
2. Disconnect the measuring tubes.
3. Set damper motor to the open position.
4. Loosen the nuts on the spindle clamp (nuts: 8mm).
5. Remove 1 screw for the locking strip on the circular design and 2
screws for the locking strip on the rectangular design (screw: TX20).
6. Lift off the damper motor and spindle adapter
(The rectangular design has a round damper spindle and no spindle
adapter).
7. Reassemble in the reverse order.
Note! Positioning of the damper blade and locking strip, see figures 17
and 18.
Figure 17. Recess in the damper spindle indicates the position of the
damper.
Figure 18. Damper open. Jumper to the left.
11
REACT V BMP
20230929 Swegon reserves the right to alter specications.

Technical data
IP class: IP54
Corrosivity class: C3
Pressure class: A
Leakage classes according to SS-EN 1751
- Leakage class, casing: C
- Leakage class circular damper, closed: 4
- Leakage class rectangular damper,
closed:
3
Running times open/close (90°):
5 Nm: 100 s
10 / 20 Nm: 150 s
Ambient temperature
Operation: 0 – +50°C
Storage: -20°C – +80°C
RH: 5 – 95%
(non-condensing)
CE marking: 2006/42/EC (MD)
2014/30/EU (EMC)
2011/65/EU (RoHS2)
Electrical data
Power supply: 24 V AC/DC ±15% 50 - 60Hz
Fixed connection cable,
1000 mm with cable size. 4 x 0.75 mm2
Power consumption, for transformer rating:
REACT V BMP 5 Nm 2.0 W 3.5 VA
REACT V BMP 10 Nm 3.0 W 5.0 VA
REACT V BMP 20 Nm 3.0 W 5.5 VA
Declaration of Conformity
Swegon AB hereby affirms that:
REACT V BMP complies with the essential characteristic
demands and relevant regulations specified in the directives,
2006/42/EC (MD), 2014/30/EU (EMC) and 2011/65 EU
(RoHS2):
The following standards have been observed:
EN ISO 12100:2010 Safety of machinery - General principles for
design - Risk assessment and risk mitigation
EN 60204-1:2006 Safety of machinery - Electrical equipment of
machines - Part 1: Generic standards
EN 60730-1:2011 Automatic electrical controls for household and
similar use - Part 1 Generic standards
EN 61000-6-2:2007 Electromagnetic compatibility (EMC). Generic
standards. Immunity for industrial environments
EN 61000-6-3:2007
Electromagnetic compatibility (EMC). Generic
standards. Emission standard for residential,
commercial and light-industrial environments
Person responsible for this declaration:
Name: Freddie Hansson, R&D Manager Tomelilla
Address: Industrigatan5, 273 21 Tomelilla, Sweden
Date: 230427
This declaration is applicable only if the product has been
installed according to the instructions in this document
and if no modifications or changes have been made on
this product.
References
www.swegon.com
Building Materials Declaration
REACT V BMP Product data sheet
REACT Belimo – Description of functions & wiring diagram
REACT V BMP
12 Swegon reserves the right to alter specications. 20230929