Swegon EAGLE Wall b Guide

EAGLE Wall b
Installation – Commissioning – Maintenance 20210525
Installation
See Figure 1.
1. Cut the opening in the wall. The size of the opening
should be according to dimensions I x J, which are
given in the Dimensions table on page 2.
2. Place the commissioning box in the opening.
3. Insert the mounting frame into the commissioning
box and secure it with screws in the short sides to the
commissioning box and to the wall structure.
4. The assembly and dismantling of the component
parts are shown in Figure 1.
5. Press the diffuser face to engage it in the mounting
frame.
Commissioning
Commissioning must be carried out with the diffuser
face mounted. Pull the measuring tube and the damper
adjustment cords out of the air diffuser through a disc.
Connect a manometer to the measuring tube. The desired
commissioning pressure can be calculated using the rated
coefficient of performance of the air diffuser. Set the
damper to the correct blade position, tie a commissioning
knot in the damper cords to indicate the damper position,
then lock the cords.
Maintenance
The air diffuser can be cleaned, if necessary, using luke-
warm water with dishwashing detergent added or by
vacuum cleaning using a brush nozzle. The duct system
can be accessed after the air diffuser section has been
removed, the acoustic baffle has been withdrawn, the air
distribution discs have been moved to the side and the
damper has been turned and withdrawn from its fastener
from the inlet. See Figure 1.
Environment
The Building Materials Declaration is available from www.
swegon.com.
To secure baffle (4) in bayonet catch and to secure the octagonal
perforated face plate (3) against the duct connection.
1. Commissioning box
2. Damper action, bayonet catch
3. Octagonal air distribution plate
4. Air distribution plate
5. Mounting frame + air diffuser
Figure 1. Installation. Commissioning.
p
k-faktor
EAGLE Wall
Tomelilla
Sweden
400-200
+ALVT1 400-200-160-B
k-faktor=14,6/27,8
k
kpq⋅=
k
pq
=
( )2
q = uppmätt flöde l/s
p= aktuellt mättryck (Pa)
k= injusteringsfaktor
5
q
q= flow reading l/s
p= current pressure reading (Pa)
k= commissioning factor
0xD / ±5% 0xD / ±5% 2xD / ±10%
Figure 2. Installation alternatives, applies for all connections (B, K)

EAGLE Wall
2Swegon reserves the right to alter specications. 20210525
ALVT 1 frame
Size A B L
300-150 330 180 230
400 -150 430 180 230
400-200 430 230 230
550-250 580 280 255
550-300 580 330 255
Figure 3. ALVT 1 frame.
Dimensions and Weights
EAGLE W
Size A B ØD F G G2 K L M I x J Weight, kg
300-150 330 180 99 295-375 225-305 270-350 85 145-225 195-275 305 x 155 3.0
400 -150 430 180 124 295-375 225-305 331- 411 85 180-260 240-320 405 x 155 3.5
400-200 430 230 159 315-395 225-305 331- 411 100 145-225 225-305 405 x 205 4.0
550-250 580 280 199 360-440 251-331 371-451 120 145-225 245-325 555 x 255 6.5
550-300 580 330 249 385-465 251-331 425-505 145 145-225 275-355 555 x 305 7.5
Size of opening = I x J
The G2, K, L and M dimensions are applicable to a side-connected commissioning
box.
Figure 6. EAGLE Wall with ALV commissioning box.
Rated coefficient of performance
EAGLE W and ALV
ALVe EAGLE Wall, supply air
Connection, rear Connection, short side
Size Size Closed slot Open slot Closed slot Open slot
300-150-100 300-100 7.8 9.2 7.2 8.1
400 -150-125 400-150 9.9 11.8 9.6 11.1
400-200-160 400-200 14.8 17.1 14 15.9
550-250-200 550-250 25.5 27. 8 24.4 26.8
550-300-250 550-300 31.1 33.9 30.5 33.4
Figure 5. Closed slot.Figure 4. Open slot.