Swegon DCPe Guide

DCPe
Installation – Commissioning – Maintenance 20180525
Accessories
Regulator unit:
REG. Combination unit with damper and sound attenuator.
Duct cover:
DCPT 1. For incorporation of the regulator unit and the
connected spiral duct.
Base:
DBCT 2. For installation on the floor.
Decorative top:
DCPT 3. Removable top board in different materials and
dimensions. Used as the termination on the top of the
diffuser when the air diffuser is connected to the duct
system via the floor. Please contact your nearest sales
representative for further information.
Installation
Secure the air diffuser with screws to the floor from the
inside of the diffuser. If a base is used, secure it with
screws to the floor and then secure it to the bottom of
the air diffuser with blind rivets. Press the regulator unit,
which has a circular connection spigot with a rubber
seal, into the inlet socket of the air diffuser. Secure the
telescopic duct cover to the aluminium profiled section.
Attach this section to the connected duct. See Figure 1.
If the duct casing is used for the duct connection from
below, an assembly fixture is required between the air dif-
fuser and ceiling.As a suggestion, spiral duct of the same
dimension as the diffuser connection can be used as the
assembly fixture between the air diffuser and ceiling.
Commissioning
The measurement tapping is positioned on the one
side of the air diffuser behind the aluminium strip. The
K-factor (COP) is given on the product identification label
on the diffuser to the side of the measurement tapping.
K-factors can also be found in the relevant commission-
ing instructions available at www.swegon.com and in this
product datasheet. We recommend that you use the REG
regulator unit for adjusting the airflow. See Figure 2.
To regulate how the air is supplied to the room, turn the
air diffuser’s Varizon®discs to make the air to flow in the
desired direction. A straight air discharge can be achieved
by taking the disc out of the diffuser, turning it 180° and
reinserting it back into place. See Figure 3.
Maintenance
The air diffuser can be cleaned, if necessary, using luke-
warm water with dishwashing detergent added or by
vacuum cleaning using a brush nozzle. The duct system is
accessed by removing the front panel and the inspection
cover of the air distribution panel. See Figure 2.
Figure 1. Installation.

DCP
2Swegon reserves the right to alter specications. 20180525
Figure 2. Commissioning, Maintenance.
Disc adjustment – Varizon®
Figure 3. Disc adjustment, schematic presentation
kpq⋅=
k
pq
=
( )2
p
k
q
K-FAC TOR
q = flow reading l/s
p = current pressure reading (Pa)
k = commissioning factor

3
20180525 Swegon reserves the right to alter specications.
DCP
Dimensions and weights
DCP
Size Dimensions (mm) Weight (kg)
ØA BØd
125 270 608 125 7
160 305 608 160 10
200 345 908 200 15
250 395 908 250 18
315 460 1488 315 23
400 545 1988 400 29
500 645 1988 500 36
630 775 1988 630 45
Figure 6. REG Regulator unit.
REG
Size Dimensions (mm)
ØC Ød G H
125 225 124 230 500
160 260 159 230 500
200 300 199 230 500
250 350 249 250 500
315 415 314 260 800
400 500 399 300 800
500 600 499 300 900
630 730 629 300 900
D
d
Figure 4. DCP.
Figure 5. DCP with duct cover and base.
1. Sizes 125-315: 2400-2750.
Sizes 400, 500, 630: 2850-3200.
If other lengths are required always state the total room height.
K-factor (COP)
Size Supply air
125 12.2
160 22.8
200 37.0
250 58.0
315 88.0
400 141.0
500 210.0
630 295.0
800 –
Number of measuring tubes: 1