Swiss Madison SM-1T114 User manual

INSTALLATION
INSTRUCTIONS
Voltaire One-Piece Toilet
SM-1T113 / SM-1T114
www.swissmadison.com | 1-434-623-4766 | [email protected]
Swiss Madison
®
Share your pictures for a feature!
using
#SwissMadison

Prior to Installation:
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
General Recommendations: Read installation and maintenance instructions thoroughly before installing the toilet.
Be sure to use proper tools and always wear proper personal safety accessories for your protection.
—1 —
Inspect toilet to ensure no damages have occurred while in shipping.
Observe all plumbing and building codes in accordance with your state and
local requirements.
Remove old toilet.
Make sure mounting surface is CLEAN and LEVEL.
All dimensions are nominal! Be sure to measure your toilet prior to installation.

—2 —
Thank you for purchasing a Swiss Madison One-Piece Toilet.
We appreciate your business and know you will enjoy your toilet for many years to come.
If you have any questions or require assistance we would be happy to help,
please contact us at 1-434-6234766 or [email protected].
Thank you for your purchase!
www.swissmadison.com
To learn more about our products, please visit:
Sincerely,
The Swiss Madison Team

ONE-PIECE TOILET MODELS
—3 —
Voltaire
29” x 18” x 28 ³⁄4”
SM-1T113 - White
Voltaire
29” x 18” x 28 ³⁄4”
SM-1T114 - White
18”
8”
18 ¹⁄2”
29”
15 ¹⁄2”
12”
28 ³⁄4”
Rough-in
18”
8”
18 ¹⁄2”
29”
15 ¹⁄2”
12”
28 ³⁄4”
Rough-in

ONE-PIECE TOILET ROUGH DIMENSIONS
—4 —
NOTE: Specialized tools may be necessary to install a Swiss Madison One-Piece Toilet, plumbing not included.
SUGGESTED TOOLS AND MATERIALS
One-Piece Toilet Wax Ring/ Gasket Bolts Side Cover Caps
Safety Glasses Wrench Level
Screwdriver
NOTE: Distance from wall to closest flange centerline must be listed as below.
Putty Knife Tape Measure
Hacksaw
Flexible Supply Tube
PARTS LIST
W”
L”
12”
H”
Rough-in

—5 —
The step-by-step guidelines in the installation instructions are a general reference.
Should there be any discrepancies, Swiss Madison cannot be held liable.
It is recommended to install all Swiss Madison products by hiring a licensed professional
2. Rough-In the Toilet
Using the measurements on the previous page, find the toilet’s rough-in.
Measure the wall from behind the toilet to the middle of the closet bolt.
NOTE: Your rough-in measurement should be around 12”.
Rough-in
1. Remove Old Toilet
Close toilet supply valve and flush tank completely, use towel or sponge to remove excess water.
Disconnect and remove supply line, if you are replacing the valve shut off the main water supply first.
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping gas.
Remove closet bolts from flange and clean away old wax and putty from base area.
ONE-PIECE TOILET INSTALLATION INSTRUCTIONS
1. Read the complete instruction manual before beginning installation.
2. Confirm that your model will fit in intended location and plumbing fixtures are located
where legally required before beginning installation.
3. Not all drawings on this manual are drawn to scale. Please refer to the model chart.
4. Two people are recommended to install and move this product.
5. Product is FRAGILE! To avoid breakage and possible injury handle with care.
NOTE: Drawings may not exactly define contour of china.

—6 —
3. Install Closet Bolts
Install closet bolts to flange channel, turn 90° and slide into place 6” (152mm) apart and parallel to wall.
Closet Flange
Closet Bolts
A
4. Install Wax Seal
Invert toilet on floor (use cushion to prevent damage), and install wax ring evenly around waste flange
with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
Wax Ring
Sealant
ONE-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.

—7 —
T
H
I
S
S
I
D
E
U
P
5. Position Toilet on Flange
Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes.
Loosely install retainer washers and nuts. Side of washers marked “THIS SIDE UP” must face up!
Closet Flange
Nut
Washer
Bolt
6. Install Toilet
Position toilet square to wall and, with a rocking motion, press bowl down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly sealed to floor.
NOTE: Do NOT over-tighten nuts as it might crack the ceramic!
Adhere bolt covers to toilet.
Smooth off the bead of sealant around the base. Remove excess sealant.
T
H
I
S
S
I
D
E
U
P
Closet Flange
Bolts
ONE-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.

ONE-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
Toilet Seat Installation
—8 —
1. Dissassemble
· Disassemble the cover cap and the hinge.
2. Construct Hinges
· Insert screw and nut into the hole on the hinge.
· Attach blind hole screw fixing to the bottom on the screw.
3. Attach Hinges
· Insert hinges with blind hole screw fixings attached into holes on toilet bowl.
· Lightly tighten hinges with a screwdriver too allow for later adjustment.
Pull
or

ONE-PIECE TOILET INSTALLATION INSTRUCTIONS
NOTE: Drawings may not exactly define contour of china.
—9 —
5. Adjust and Attach Seat
· Align seat to the hinges then firmly tighten the hinges.
· Attach seat to the secure hinges.
· Adjust seat to align to the bowl.
6. Usage
· To remove, push middle button until you hear a “click”, then pull straight up.
· To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.
*Click* *Click*
4. Adjust and Cover Hinges
· Be sure the hinge is all the way forward for proper seat fitting.
· Place the covers onto the hinges.
Incorrect: Correct: