Swiss Madison Back-to-Wall User manual

@SwissMadison
#WellMadeForever
www.swissmadison.com | 1-434-623-4766 | [email protected]
Swiss Madison
®
INSTALLATION INSTRUCTIONS
Back-to-Wall Toilet

—1 —
If you have any questions or concerns please contact us:
1-434-623-4766
[email protected]
PRIOR TO INSTALLATION:
· Inspect toilet to ensure no damages have occurred while in shipping.
· Observe all plumbing and building codes in accordance with your state and local requirements.
· All dimensions are nominal! Be sure to measure your toilet prior to installation.
· The step-by-step guidelines in the installation instructions are a general reference. Should there be
any discrepancies, Swiss Madison cannot be held liable. It is recommended to install all Swiss
Madison products by hiring a licensed professional.
· Read installation and maintenance instructions thoroughly before installing. Be sure to use proper
tools and always wear proper personal safety accessories for your protection.
· Two people are recommended to handle and install this product as it is fragile.
INCLUDED PARTS:
SUGGESTED TOOLS & MATERIALS:
Safety
Glasses Wrench
Level
Screwdriver
Putty Knife
HacksawFlexible
Supply Tube
Tape
Measure
Bolts
Back-to-Wall
Toilet Flange and
Inlet Pipe
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS
Sealant

—2 —
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS
3. Cut Pipes
· Remove pipes from the bowl and measure the
space between the marks on the pipes.
· Carry this measurement over to the end of the pipes,
adding 3/16” and then cut off the end of the pipes.
· After cutting, be sure to chamfer cut edges.
4. Connect Pipes
· Apply lubricant onto rubber washers of straight tube
and connecting pipe.
· Place the toilet, making sure the pipes fit properly, and
the toilet is making contact with the floor and wall
surface.
Straight
tube Connecting
pipe
+ 1/8”
+ 3mm
+ 3/16”
+ 5mm
2. Dry Fit Flange and Inlet Pipe
· Fully insert straight tube into cistern flushing outlet
then connect pipe into discharge outlet.
· Remove pipes from the sanitary unit and insert
them completely into the back of the bowl. Then mark
pipes where they extend past the edges of the bowl.
1. Install Tank
· Before toilet bowl installation, a wood frame and
commercial or residential tank system is required.
· Install according to manufactuer’s instructions.
+ 3mm
+ 5mm

—3 —
BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS
5. Fit and Level Bowl
· Place the bowl facing the flush pipe and waste
pipe, then push firmly until it touches the wall to
ensure that both pipes are in the correct position
and the correct length.
· Make sure bowl is level then mark on both sides of
the bowl where the anchors will be installed.
7. Install and Secure Toilet
· Make sure the pipes fit in properly and the toilet is
making contact with the floor and the wall surface.
· Once the toilet is placed properly, tighten the bolts
to secure the toilet.
8. Seal Edges
· Apply a thin layer of silicone sealant around the
perimeter of the toilet bowl. The use of an anti-mold
silicone is recommended. Remove any excess
silicone with a paper towel.
6. Install Anchors and Brackets
· Remove the toilet bowl and measure the thickness
of the bowl. Then apply that measurement in
towards the center from the marks on the floor.
· Insert anchors and install brackets.
Thickness of the
toilet bowl
measurement
Edge of toilet
marking
Anchors

BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS
TOILET SEAT INSTALLATION
—4 —
1. Dissassemble
· Disassemble the cover cap and the hinge.
2. Construct Hinges
· Insert screw and nut into the hole on the hinge.
· Attach blind hole screw fixing to the bottom of screw.
3. Attach Hinges
· Insert hinges with blind hole screw fixings
attached into holes on toilet bowl.
· Lightly tighten hinges with a screwdriver to
allow for later adjustment.
Pull
4. Adjust and Cover Hinges
· Be sure the hinge is all the way forward for proper
seat fitting.
· Place the covers onto the hinges.
or
Incorrect: Correct:

BACK-TO-WALL TOILET INSTALLATION INSTRUCTIONS
—5 —
5. Adjust and Attach Seat
· Align seat to the hinges then firmly tighten the hinges.
· Attach seat to the secure hinges.
· Adjust seat to align to the bowl.
TOILET SEAT USAGE
· To remove, push middle button until you hear a “click”, then pull straight up.
· To re-install, align hinge posts with reference marks on seat, then push down until your hear a “click”.
*Click* *Click*
One Button:
Two Button:
*Click* *Click*

1-434-MADISON
(623-4766)
19 Stults Road
Dayton, NJ 08810
www.swissmadison.com
ONE YEAR LIMITED WARRANTY
Swiss Madison® products are made with quality materials and excellent craftsmanship to provide our
customers with beautiful, durable, long-lasting products. Should there be any defects in materials or
craftsmanship under regular use that are discovered within the first year of installation, Swiss Madison®
will provide replacement parts at no charge, or at its discretion, replace any product or part of the product
that is deemed defective, under normal installation, use, service or maintenance. This warranty applies
only to the original purchaser. Proof of purchase will be required in the instance of a claim.
Swiss Madison®recommends all installations of Swiss Madison® products to be conducted by a
licensed, professional plumber or contractor. Swiss Madison®will not be held responsible for any
damage or product failure due to improper installation, misuse, or failure to utilize a licensed professional
for installation. Swiss Madison® is not responsible for any installation or removal costs.
This One Year Limited Warranty Will Be Voided If:
• The installation recommendations were not followed by the installer
• The product has been moved from its initial place of installation
• The product has in any way been modified from its packaged state
• The product has been subjected to improper maintenance, abuse, misuse, excessive use of
chemicals, accidents, or other damages, etc.
Swiss Madison®makes no implication that its products comply with any local building or plumbing
codes. It is the consumer’s responsibility and obligation to determine local code compliance prior to and
during installation. This warranty extends only to the original purchaser and first consumer.
Swiss Madison®is not responsible for any special, incidental or consequential damages associated with
the installation, replacement, return or use of the original purchaser’s product. This includes, but is not
limited to: freight costs, labor, travel time, lost profit, home damages and other contingent liabilities and
costs (including, without limitation, costs associated with ‘professionals’ or ‘experts’, investigations,
audits, analyses, attorneys and any other professional/hired services).
The Swiss Madison®warranty is a comprehensive and explicit limit of liability. All items not disclosed
within the warranty are not addressable within the responsibility of Swiss Madison®. Certain states have
variances regarding implied warranties; in those situations, we remain fully compliant.
If you have any questions or concerns, please contact us directly at
1-434-MADISON (623-4766)
WARNING: Contents of your order may contain sharp and possibly other harmful pieces and may
cause hazard to children and adults. Swiss Madison®is not responsible in any way for personal dam-
ages.
Swiss Madison
®