Swiss 200 series User manual

www.tresore.ch

OPERATING INSTRUCTIONS

FURNITURE SAFE

SERIES 200 AND 300

with electronic keypad lock

Issue 08.2020

Thank you very much ❤

We would like to thank you for choosing Waldis when it comes to safety.

When buying a safe, you have chosen a product tested according to EN1143-1. A

Swiss quality product with VdS - tested security.

Please read these instructions carefully before commissioning your safe!

Your contact for questions

WALDIS Tresore AG

Hofwisenstrasse 20

CH-8153 Rümlang

Phone: +41 43 211 12 00

Fax: +41 43 211 12 12

E-Mail: info@tresore.ch

Table of contents

Safe lock ................................................................................................................ 1

1.1. General notes .................................................................................................. 1

1.1.1. Opening the lock ....................................................................................... 1

1.1.2. Closing the lock......................................................................................... 1

Programming.......................................................................................................... 2

2.1. Code Programming ......................................................................................... 2

Power supply.......................................................................................................... 3

3.1. Battery change ................................................................................................ 3

3.1.1. Opening when the battery is empty........................................................... 3

3.1.2. Battery change.......................................................................................... 3

Password ............................................................................................................... 4

4.1. General basic rules.......................................................................................... 4

4.1.1. Avoid obvious passwords.......................................................................... 4

4.1.2. Tips ........................................................................................................... 4

4.1.3. Last but not least....................................................................................... 4

1

Safe lock

1.1. General notes

When operating the cabinet, there is an increased risk of crushing in the door or

the hinges! WALDIS Tresore AG expressly disclaims any liability for injuries which

may result from improper operation of the door. Before operating the safe, these

instructions must be read and understood completely.

1.1.1. Opening the lock

Procedure

1. Press ® key.

2. Enter code (set to 0 0 0 0 0 during initial startup).

3. If the entry is correct, the green diode lights up for approx. 8 seconds and

flashes, then for 20 seconds. The door can be opened.

1.1.2. Closing the lock

Procedure

1. Close the door and press the ® key followed by the © key.

2. red diode lights up for approx. seconds and then flashes for approx. 20

seconds.

1234

5678

90CR

2

Programming

Important: Program only when the door is open!

2.1. Code Programming

Procedure

1. Press ® key.

2. Enter the existing code (for initial start-up 0 0 0 0 0) and press the © key

(green diode indicates correct entry).

3. Enter the new code (6 to 10 numbers or letters) and press ©.

4. Enter the new code again and press the © key.

If the entry is correct, two short acoustic signals sound and the green diode

lights up

briefly twice.

If the code is not entered correctly, an acoustic signal sounds for one second

and the red diode lights up for one second. The new code has therefore not

been saved and the old code (0 0 0 0 0 for initial start-up) remains

programmed in this case. Repeat procedure from point 2.1.

Press the ® key and then the © key without closing the door. The bolts are

now pushed forward.

Important: Test several times with the door open whether the code was

correctly accepted has been correctly accepted before you close

the door!

3

Power supply

3.1. Battery change

3.1.1. Opening when the battery is empty

1 new block battery 9V press on the two contact points of the keypad and enter

the code.

3.1.2. Battery change

Open the battery compartment cover according to the sketch and replace the

battery.

4

Password

4.1. General basic rules

4.1.1. Avoid obvious passwords

•No trivial values like 000000, 0815, 123456

•Do not use your own birthday, car license plate, phone number or name (your

own, wife/husband, children, pets, company, place of residence, etc.) as

password. Do not use standard passwords like: "password" or "safe".

•Writing backwards is also too easy.

•Do not use a password that you already use.

•Important passwords should not have a logical structure.

4.1.2. Tips

•The first rule: A password is only secure if it remains secret!

•Remember passwords - don't write them down anywhere!

•Consider all keys if possible (wear marks on the keyboard betray the individual

numbers over time)

4.1.3. Last but not least

Consider how the password will still be retained if the owner can no longer

disclose the password (e.g., in the event of death). Leave a sealed envelope with

your notary.

Notes

_______________________________________________________________________________

Swiss 200 Series User manual

Popular Safe manuals by other brands