Symmetry SWITCHBACK 3-LEG-C-STYLE User manual

#2 Phillips Screwdriver or Bit Cordless Drill/Driver
C(x1)
E(x1)
F(x1)
K(x1)
5mm Allen Key
M6x16mm Screw
S-A
M6x16mm Screw
S-B
M10x16mm Screw
S-D
M5x20mm Screw
S-C
M4x22mm Screw
S-E
D(x2)
H(x2)
J(x2)
I(x4)
B(x2)
A(x1)
G(x1)
No. C6263 Rev. 01
Release Date: XX/XX/2019
IMPORTANT: PLEASE READ ALL INSTRUCTIONS BEFORE STARTING ASSEMBLY.
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
REQUIRED TOOLSEXAMPLE FINAL ASSEMBLY
COMPONENTS
CARTON 1 CARTON 2
S-A
(x4)
S-C
(x10)
S-D
(x8)
S-B
(x4)
S-C
(x10)
S-E
(x2)
K(x1)
5mm Allen Key
1:1 SCALE
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

S-B
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
1
1. Install end pipe onto the column as shown in the illustration.
2. Install four socket screws M6x16mm with provided 5mm Allen Key.
3. Install outer pipes using four M6x16mm screws. Do not tighten more than
half way.
4. Install cable clamps into corner bracket as shown.
Carton 1 - 3rd Leg Kit
B
K
A
C
S-A
K
2
3
1
4
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

Carton 2 - Base Kit
1. Rotate the columns into upright position.
2. Separate U pipes and install end pipes into columns.
3. Tighten the 4 bolts (already in place) on each side that secure the motor
housing for each of the columns using the Allen wrench provided.
Note:
K
S-A
2
G
1
3
If U pipes do not separate
easily, loosen set screws.
Note: If a table side is 72" long, discard the U
pipes shipped with unit and replace
with longer U pipes shipped separately.
This may affect one or both sides.
End Pipe
Outer Pipe
U Pipe
SWITCHBACK, 3-LEG, C-STYLE ASSEMBLY INSTRUCTIONS
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
2
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

K
1. Unfasten the set screws half way out for the U pipes to be installed into
the columns using the 5mm Allen wrench provided.
1 2
1
Note: Use longer U pipes for 72” surface.
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
3
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

1. Install all U pipes into the outer pipes locate the base per pilot hole
pattern or in desired location.
2. Secure U pipes by tightening set screws with provided 5mm Allen key.
3. Fully install the four M6x16mm screws to secure table configuration.
Note:
When combining two surfaces, place the tops in
position and then place the entire base assembly
in position on top of the face down tops. Locate
and install each mending plate as shown using
the 8 M5x19mm screws provided. Location of the
plates may vary based on table size and presence
of grommets.
3
1
90°
or
1 2
120°
1
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
4
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS
2

S-D
J
1. Install table feet using 4 screws per leg (M10x16mm) with provided
Allen key.
Note: When assembling C style legs, make sure the end brackets and feet are extended in the
same direction as shown.
1
1
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
5
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

1. Connect AC Power cord to control box.
2. Connect 18”(500mm) additional cord from the control box to the other
column. Tuck all excess cords in the frame use the wire clamps already
in place.
3. Connect the handset to the control box. Tuck the control box cord
through the frame notch. Note: This must be done before securing base to top.
4. Connect cord from center column to control box.
Note: For a unit with at least one 72" side,
a 39" extension for connecting the
units is provided separately.
1
4
2
3
1
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
6
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS

1. Install columns to table top using 14 M5x20mm screws.
2. Install handset to table top using 2 M4x22mm screws.
3. Place table in the upright position, be cautious to not damage handset.
S-D
Note: Resetting the table: Press and hold the up & down buttons at the same time for 3 seconds.
Continue pressing until the columns are in the lowest position. When finished resetting, the control
box will make a sound and the buttons can be released. Now the system is operational.
1
3
S-E
2
1
For more information, visit www.symmetryoffice.com
To report any issues with this product, please contact our customer service department at [phone]
7
SWITCHBACK 3-LEG-C-STYLE ASSEMBLY INSTRUCTIONS