Symmetry SWITCHBACK User manual

#2 Phillips Screwdriver or Bit Cordless Drill/Driver
M10x16mm Screw
S-B
M5x20mm Screw
S-A
M4x22mm Screw
S-C
No. C6286 Rev. B
Date: 2/19/2020
IMPORTANT: PLEASE READ ALL INSTRUCTIONS BEFORE STARTING ASSEMBLY.
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
REQUIRED TOOLS
FINAL ASSEMBLY EXAMPLE
COMPONENTS
1:1 SCALE
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
S-A
(x7)
S-B
(x8)
S-C
(x2)
S-D
(x2)
S-E
(x4)
S-F
(x4)
G-A(x1)
6mm Allen Key
(Alt - only for specific models)
A(x2)
B(x2)
E(x2)
C(x2)
D(x1)
F(x1)
M6x16mm Screw
S-E S-F
S-D
M10x17mm Set Screw M6x8mm Screw
'
H(x1)
S-B (Alternate)
(x8)
M10x30mm Screw
S-B (Alternate)
G(x1)
5mm Allen Key

For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1. For proper cable management, align the hand control and control
box on provided hole patterns with control box three (3) ports facing
the leg it is closest to.
1
T-Leg C-Leg

For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
2
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
2
A
S-E
D
C
1. Place the columns into an upright position.
2. Fasten the two (2) M6 x 16mm screws on each leg that secure the
motor housing to the cross-brace using the Allen wrench provided.
3. Insert u-pipe.
1
3
Note: Be sure to place the cross-brace such that the
cutaway portions are in contact with the table
surface and facing each other.
2
 
I @0
Cutaway Portion

1. Install end pipes into columns with two (2) M6 x 8mm screws per side
using the provided Allen wrench.
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
3
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
T-Leg
C-Leg
1
S-F
S-F
1
B
B

1. Install table feet using four (4) M10 x 16mm screws per leg using
provided Allen wrench.
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
4
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1
Note: For C-leg models, make sure the end pipes and feet are extended in the same direction.
T-LegC-Leg
S-B
S-B
1
30", C-Leg
Alternate Design
S-B
(Alternate)

1. Place the frame assembly onto the underside of the tabletop. Extend
the frame to the desired length. Once the legs are located, center the
u-pipe and fasten the two (2) M10 x 17mm set screws as shown.
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
5
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1
T-Leg Shown
S-D

For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
6
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1
S-C
1.Place the control box and hand control in position as shown.
Note: For T-leg models, control box should be placed on side closest to user.
Note: For C-leg models, control box should be placed on side farthest from user.
T-Leg C-Leg
H
F
F
H
S-A
S-C
S-A
1
3
2. Attach hand control to tabletop with the two (2) M4 x 22mm screws provided.
3. Attach the control box to tabletop with the two (2) M5 x 20mm screws provided.
2
1

1. Attach the frame assembly onto the underside of the tabletop using
M5 x 20mm screws provided. (See hardware requirements table)
2. Attach all cables to control box before connecting power cord.
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
7
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1
Table Depth
24” 7
13
5
5
30”
C-Leg T-Leg
S-A
2
T-Leg Shown
Hardware Requirements

1
For more information, visit www.symmetryoffice.com.
To report any issues with this product, please contact our customer service department at [phone].
8
SWITCHBACK 2-LEG 2-STAGE ASSEMBLY INSTRUCTIONS
1. Flip the table to the upright position and reset it before the first use.
Resetting the table:
Press and hold the up and down buttons at the same time for three (3) seconds. Continue
pressing until the columns are in the lowest position. When finished resetting, the control box will
beep and the buttons can be released. The system is now operational.