Symmetry Voyager User manual

2-LEG VOYAGER
WITH OR WITHOUT HAT CHANNEL
VOYAG E R
ASSEMBLY INSTRUCTIONS
Reach new heights with the Voyager 2-leg sit/stand table. Designed and built to be
congurable for spaces of any shape and size, get the do-it-all desk that works with a
multitude of convenient workspace options.

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
REQUIRED TOOLSCOMPONENT LIST
COMPONENTS
1:1 SCALE
2
2-LEG VOYAGER WITHOUT HAT CHANNEL
FOR TABLE TOPS UNDER 72"
Cordless Drill / Driver
(Do not over-tighten screws)
Torx L-Key, T40 Size
Hex L-Key, 6 mm Size
#2 Phillips-Head
Screwdriver or Bit
Top Support
Column
Foot
M10 × 1.5 30 mm Screws
M8 × 1.25 12 mm Screw
Foam*
Motor Housing
#10 × ¾" Screws
Power Cord
Control
Controller
*Do not remove foam.
#10 × ¾" Screw M10 × 1.5 30 mm Screw M8 × 1.25 12 mm Screw
• M8 × 1.25 12mm Screws (8)
• M10 × 1.5 30 mm Screws (4)
• #10 × ¾" Screws (22)
• Column (2)
• Controller (1)
• Control Box (1)
• Foot (2)
• Motor Housing (2)
• Power Cord (1)
• Top Support (2)

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
REQUIRED TOOLSCOMPONENT LIST
COMPONENTS
1:1 SCALE
3
Top Support
Column
Foot
M10 × 1.5 30 mm Screws
M8 × 1.25 12 mm Screws
Foam*
HAT Channel
Motor Housing
#10 × ¾" Screws
#10 × ¾" Screws
Power Cord
Control
Controller
*Do not remove foam.
2-LEG VOYAGER WITH HAT CHANNEL
FOR 72" TABLE TOPS
Cordless Drill / Driver
(Do not over-tighten screws)
Torx L-Key, T40 Size
Hex L-Key, 6 mm Size
#2 Phillips-Head
Screwdriver or Bit
#10 × ¾" Screw M10 × 1.5 30 mm Screw M8 × 1.25 12 mm Screw
• M8 × 1.25 12mm Screws (8)
• M10 × 1.5 30 mm Screws (4)
• #10 × ¾" Screws (30)
• Column (2)
• HAT Channel
• Controller (1)
• Control Box (1)
• Foot (2)
• Motor Housing (2)
• Power Cord (1)
• Top Support (2)

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
1
4
1. Check to make sure the top supports are 13/8" from the edge of the table top and align
the support with the pilot holes.
2. Attach both top supports to the underside of the table top using a #2 Phillips-head
screwdriver or bit and the #10 × ¾" screws (8 per top support).

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
2
5
For each top support:
1. Feed the motor cables through the motor housing.
2. Center the motor housing in the top support, ensuring that the mounting holes in the
motor housing and the column remain aligned.
3. Fasten the three parts together using the T40 Torx L-key and the M8 × 1.25 12 mm
screws (4 per column).

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
3
6
1. Attach the feet to the columns using the 6 mm hex L-key and the M10 × 1.5 30 mm
screws (2 per column).

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
4
7
1. Attach the motor housing to the underside of the table top using a #2 Phillips-head
screwdriver or bit and #10 × ¾" screws (2 per motor housing).
Screws belong inside
the motor housing.

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
5
5
8
Complete this step only if using a HAT channel. HAT channels are required for tables
with a length of 72" or greater. If no HAT channel is being used, proceed to step 6.
1. Feed the motor cables through the HAT channel before attaching the HAT channel to the
table top.
2. Attach the HAT channel to underside of the table top using a #2 Phillips-head screwdriver
or bit and #10 × ¾" screws (8).

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
5
6
9
Making sure that the control box and controller are fastened in a location where all the
cables will connect without tension:
1. Fasten the control box to the underside of the table top using a #2 Phillips-head
screwdriver or bit and #10 × ¾" screws (2).
2. Fasten the controller to the underside of the table top using a #2 Phillips-head
screwdriver or bit and #10 × ¾" screws (2).

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG ASSEMBLY INSTRUCTIONS
STEPS
5
7
10
1. Connect the motor cables (M1–M2) to the control box. The motor cable plug connection
should click into place.
2. Connect the controller (HS) cable to the control box.
3. Connect the supplied power cord (AC) to the control box.
4. Attach all cables to the table top to avoid damage during operation.
Never attach cables or cords to legs.

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG SAFETY INFORMATION
DANGER
1111
Save these instructions.
KEEP AWAY FROM CHILDREN
This table system is not designed for use in homes
or other areas accessible by small children.
BE CAREFUL WHEN ADJUSTING
TABLE HEIGHT
Body parts and property can be caught between
the moving table top and immobile obstacles (such
as shelves, furniture, window sills or walls). Keep at
least one inch of clearance around desk to make
sure nothing is in the table's path for its entire
range of motion.
Before raising or lowering:
• Check the surroundings on all sides of the table
are clear.
• Make sure corded objects will not be pulled o
the table or cause other objects to fall.
• Make sure the table power cord moves freely
as desk moves up and down.
USE CARE WHEN MOVING TABLE
• Clear all objects and equipment from the
table before rolling to reduce the risk of
tipping over.
• Do not move a loaded desk.
• Do not lift the desk by the table top.
• Adjust the desk to its lowest height
before moving.
To reduce the risk of death, serious injury, or property damage: Read and follow the safety
information and the provided instructions when assembling this product. Do not change or
replace components and accessories provided by Symmetry Oce.
1"
1"
1" 1"
1"
1"
Lowest Height: 28.5"
Maximum Height: 47.25"
Height Range: 18.75"

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER 2-LEG SAFETY INFORMATION
DANGER
1212
DO NOT OVERLOAD TABLE
To prevent the table from tipping or collapsing, make sure the table frame is not overloaded by the
weight of the table top and objects on table.
• Evenly distribute load; excess loads near the edges can reduce stability and lead to tip-over.
• Do not exceed maximum load of 200 lb or 91 kg (this includes the weight of the table top).
• Do not exceed maximum edge load of 25 lb when positioning monitors or mounting accessories.
• Do not sit or stand on the table.
ONLY INSTALL APPROVED TABLE TOPS
This table system does not include a table top. Table tops must be ordered separately.
Table tops must be at least ¾" thick and weigh no more than 5 lb per square foot.
(For example: a 2' × 6' desktop should weigh no more than 60 lb.) Do not exceed the maximum weight
capacity, including both the table top and the objects on the table top. If you are unsure, contact
customer service.
KEEP TABLE FRAME DRY
Keep all electrical components away from water and humidity. Not approved for outdoor use.
To reduce the risk of electric shock:
Always unplug this table from the electrical outlet before cleaning.
GROUNDING INSTRUCTIONS
This product is equipped with a cord that has an
equipment-grounding conductor and a grounding
plug. Use only the cord provided. Make sure that
the product is connected to an outlet that has the
same conguration as the plug and is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the product.
If it will not t the outlet, have a proper outlet
installed by a qualied electrician.
No adapters are to be used with this product.
Keep cord away from heated surfaces.
Grounded Outlet Box
Grounding
Pin
Grounded
Outlet

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER OPERATION INFORMATION
1313
INITIALIZATION / RESET
The desk must be initialized/reset after any of the following:
• After assembly
• After disconnection from the power supply
• After any impact on the table top
To initialize or reset:
1. Move the table to the lowest position by pressing the button on the controller until the columns
reach the lowest position.
2. Press the button again and hold it for ve seconds or until the table moves slightly down to the
machine zero point and back up to the operation zero point.
3. Once the table stops moving, release the button. If the button is released too soon, the table
legs will not move up. Repeat the reset process.
The upper height position is programmed into the control box. For this reason, only use the control box
that has been provided with the specic table frame. Under no circumstance should a control box be
moved from one table to another.
CONTROLLER OPERATION
Press the or button and the table will move up or down to the desired position. Once the
desired position is reached, let go of the up or down button. The table will stop once it reaches the
upper or lower height position.
1
s
2 3 4
Programmable ControllerStandard Up/Down Controller

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER OPERATION INFORMATION
1414
PROGRAMMABLE CONTROLLER
The optional programmable controller is equipped with a display that shows the current table height in
centimeters or inches. The controller also will display an error code if an error is detected by the control
box. When an error code is detected, the display will show an error code EXX instead of the current
table height. To resolve the error, see the troubleshooting section on page 14.
Change the Height Unit:
The height display of the controller can display
either centimeters or inches. With the help of
the S5-menus, the unit can be changed. If the
display was originally set to centimeters, then
after the procedure noted below it will change to
inches or vice versa.
Follow these steps:
1. Press and hold the 1, 2, and buttons for 5
seconds or until the display shows "S5."
2. Conrm by pressing the S button. Now the
display will have changed.
To exit the menu without making a selection, wait
approximately 10 seconds until the height display
appears again.
Save Memory Position:
Drive the table up or down to the desired height.
Press the S button (in the display “S -” is shown).
Select a position by pressing on any of the four
number buttons, 1-4, (the display will show the
setting as “S1”). The save shows the current
table height. Repeat steps to save a maximum of
four dierent positions.
Recall Memory Position – Manual:
Press and hold the desired memory location
button (1, 2, 3 or 4) and the table moves from the
current position into the saved position.
The button must be pressed until the position
is reached. If the button is released prior to the
display showing the memory number, the table
will stop short of the desired height.
Recall Memory Position – Automatic :
Quickly double click (within less than 0.5
seconds) the desired memory location button
(1, 2, 3, or 4) and the table moves from the
current position into the saved position. The
button may be released after the double click.
Ensure that no objects are in the path of the table
during movement. Pressing any button will stop
the table movement.
Reset Control Unit to Factory Setting :
If the indicated value does not match the actual
height of the table top, the display can be
corrected as follows:
1. Press and HOLD the 1,2, and buttons
simultaneously. Keep button combination
pressed for roughly 10 seconds.
2. Display will show "S" and a number, e.g. "S5"
3. Release buttons.
4. Press and release button until the display
reads "S0." (Note: it may take 2 press and
release sequences before "S0" is displayed.)
5. Press S (green) memory. Control box should
click 5 times.
6. Control unit will reset to its factory settings.
"E61" will be displayed on the controller.
(Note: The menu timeout is 5 seconds; this
means the menu will close automatically
without storing the new settings if the user
does not press a key for 5 seconds.)
Important: After control unit is reset to
factory settings, perform initialization
process as explained on page 14.

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER TROUBLESHOOTING
151515
AT SET-UP
If the table does not function immediately upon installation:
1. Disconnect everything from the control box, including the power cord and wait a few minutes.
2. Plug the power into the control box and ensure cabling is secure.
3. Plug the legs into the control box and ensure the cabling is secure.
4. Plug the controller into the control box and ensure the cabling is secure.
5. Follow the initialization instructions on page 12.
If problems persist:
Call Symmetry Oce before you leave the job site for diagnostic help: 888-552-5699.
SYMPTOM SOURCE SOLUTION
Table does not move
No power supply Plug in the power cord or check the
connection on the control box
No connection or a loose connection to
the drives
Verify the plug connections of the motor
cable to the control box
No connection or a loose connection to
the controller
Verify the plug connections of the motor
cable to the control box
Maximum lifting capacity is exceeded Reduce the weight or load on the
desktop
Maximum time limit is exceeded Control is activated automatically after
approx. 9 minutes
Defective drive Contact customer service
Defective control box Contact customer service
Controller is defective Replace the controller.
Table moves down at a slow rate Control box needs to be reset Reset cohandsentrol box. (See page 12)
During operation,
tables moves at a slow rate Maximum lifting capacity is exceeded Reduce weight
Table moves briey on only one
side and then stops
No connection or a loose connection
to the drives
Verify the plug connections of the motor
cable to the control box and reset the
control box
Defective drive Contact customer service
OTHER CONCERNS

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER TROUBLESHOOTING
161616
CODE SOURCE SOLUTION
H0T
The control box monitors the duty cycle
(time-controlled) and its maximum
temperature. A value has been exceeded.
Wait until the “H0T” display goes out - the table is working properly
again
E00 M1 – Internal fault
Unplug and contact customer service.
E01 M2 – Internal fault
E02 M3 – Internal fault
E12 M1 – Defect Unplug. Correct the external short circuit and/or verify the cable to
the drives. Plug cables into the control box and re-initialize the table
(see page 12.)
E13 M2 – Defect
E14 M3 – Defect
E24 M1 – Overcurrent Collision — Resolve if necessary.
E25 M2 – Overcurrent Maximum load exceeded — Remove excess load from table.
E26 M3 – Overcurrent If the problem still exists, please contact customer service.
E36 M1 – Not connected
Motor not connected. Check cable/connector to the drive.
Reset the table (see page 12).
E37 M2 – Not connected
E38 M3 – Not connected
E48 Overcurrent drive 1 Collision — Resolve if necessary.
E49 Overcurrent drive 2 Maximum load exceeded — Remove excess load from table.
E55 Drive 1 – Synchronization is lost If necessary, reduce the load on the table.
E55 Drive 1 – Synchronization is lost Reset the table (see page 12).
E60 Collision identied Optional ISP function — Remove source.
E61 Drive replaced The connection to the drive is interrupted or a new drive is
connected. Reset the table (see page 12).
E67 High voltage Unplug the power cord and contage customer service. High voltage
driver in control unit failed.
E81 Internal error
Make a manual reset (see page 12). Unplug the power cord then
plug it in again after a few seconds. If this error occurs frequently,
unplug the power cord and contact customer service
E93 Connection error in the cascaded network
Check all the cable connections and try to reset the motors. If you
cannot reset the motors, disconnect all the control units from the
power supply. Wait for at least 5 seconds and then reconnect all the
control units to the power supply. Try again to reset the motors. If
you still cannot reset the motors, please contact customer service.
UNDERSTANDING ERROR CODES
If it is not possible to resolve an error as described, disconnect the power cord, wait a few minutes
and reset the table again. If the error still occurs, remove the table from the power source and contact
customer service.

To report any issues with this product, please contact our customer service department at [phone].
For more information, visit www.symmetryoce.com
VOYAGER
171717
GENERAL CONTROL BOX
Power supply 120 VAC ± 10% / 60 Hz
Standby power consumption, primary <0.3 W
Operating temperature 0–35º C
Protection class IP 20
Maximum power output 216VA / 24V
2-LEG FRAME WITH CONTROL BOX
Maximum lift capacity 200 lb (� 90 kg / 890 N)
Adjustable range 18.9"
Maximum input current 6.5 A
Maximum duty cycle 10% (2 minutes on / 18 minutes o)
TECHNICAL DATA
STANDARDS AND CERTIFICATIONS
The drive system is tested according to the following standards:
• UL 962
Issued: 2014/11/07 Ed: 4 Household and Commercial Furnishings
• CSA C22.2#68
Issued: 2009/09/01 Ed: 7 (R2014)
Motor-Operated Appliances (Household and Commercial)
• Meets BIFMA X5.5 2014
WARRANTY
Contact your sales representative for warranty information.
System: Clever
OMT-Veyhl USA
11511 James Street
Holland, MI 49424
Intertek listing belongs to: