Symmons Allura S-4704-TRM Manual

Model Numbers Specification
Options/Modifications
Tub/hand shower trim with lever handle and secondary
integral diverter handle includes wall connection, cradle
for hand shower mounting, non-diverter tub spout,
in-line vacuum breaker, exible metal hose and 3 mode
hand shower with 2.5 gpm (9.5 L/min) ow restrictor.
Components made from metal and plastic materials
plated in standard polished chrome nish.
Allura®Tub/Hand Shower Trim
Operation & Maintenance Manual
S-4704-TRM
S-4704-TRM
Valve Trim with Hand Shower
Compliance
-1.5
1.5 gpm (5.7 L/min) flow restrictor
-2.0
2.0 gpm (7.6 L/min) flow restrictor
-LAM
Metal finish insert handle
-LR
Lever handle
Note: Append appropriate -sufx to model number.
-STN
Satin Nickel finish
-ASME A112.18.1; CSA B125.1
-H323-V
30” slide bar in place of wall cradle on hand
shower units
-SS
Slip spout on any tub and shower unit
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.

2
Dimensions
Notes:
1) All dimensions measured from nominal rough-in (see L as reference).
2) Dimensions subject to change without notice.
Measurements
A Ø 2 1/8”, 54 mm
B Ø 7”, 178 mm
C 6”, 152 mm right or left
D
Male 1/2” NPT thread must
be recessed 1/4” from
nished wall
E 2 1/2”, 64 mm
F Ref. 32”, 813 mm
G 12”, 305 mm
H 3 1/8”, 79 mm
I 4 1/8”, 105 mm
J 1/2” NPT
K 4”, 102 mm
LRough-in
2 3/8” ± 1/2”, 60 mm ± 13 mm
M 5 1/2”, 140 mm
AA
B
B
F
F
G
G
D
D
H
H
I
I
L
L
M
M
K
K
J
J
Floor
Floor
E
E
CC

3
Parts Breakdown
Replacement Parts
Item Description Part Number
AIn-line Vacuum
Breaker EF-109
B Wall Elbow EF-105
C
D
E
Wall Cradle
Cradle Hardware
Cradle Mount
EF-106
F
G
H
I
Plug Button
Handle Screw
Star Washer
Handle
RTS-026
J Dome Cover T-19
K
L
M
Dial
Mounting Screws
Shower Escutcheon
T-131A
NHand Shower HS-143
OSecondary Lever
Handle T-139
P Tub Spout 060
Q5” Hose with
Vaccum Breaker EF-104
Tools Required for Installation
Adjustable
wrench
Allen wrench
(3/16”)
Phillips head
screwdriver
Plumber tape
Silicone
*Note: Apply a bead of silicone around the perimeter of the escutcheon
after installing trim ush with wall. Leave opening on bottom of
escutcheon for weep hole.
Notes:
1) Append -STN to part number for Satin Nickel
nish.
2) Append -1.5 or -2.0 hand shower for low ow.
O
D
C
E
N
A
B
J
L
K
P
Q
M
F
I
G
H

4
Installation
Note:
For valve body installation, please
see valve body manual.
1) Attach integral diverter handle (O)
to shower escutcheon (M).
2) Install shower escutcheon (M) to
shower valve (S-4002-BODY).
Secure with two screws (L). Snap
dial (K) into shower escutcheon.
3) Install dome cover (J) to valve by
turning clockwise.
4) Install handle (I) to valve. Secure
handle with star washer (H) and
set screw (G). Attach plug button
(F) to handle.
Note: Handle should be facing the
6 o'clock position.
5) Install tub spout (P) to pipe tting.
Turn clockwise to secure.
6) Install wall elbow (B) to recessed
pipe tting. Tighten set screw to
secure.
7) Place cradle mounting plate (E) in
position, mark and drill 1/8" pilot
holes into stud.
OM
1
3
2
L
M
K
1
2
J
1
3
2
G
H
I
F
1
2
P
1
2
B
1
2
E

5
Installation
Option: Place mounting plate (E) in
position, mark and drill 3/16" holes
into wall. Install anchors.
8) Remove cover of hand shower
cradle (C) . Install cradle and
mounting plate (E) . Secure with
three screws (D) . Replace cover
on hand shower cradle.
9) Attach large end of hand shower
hose (Q) to hand shower
(N). Connect in-line vacuum
breaker to wall elbow (B). Turn
clockwise to tighten.
4
3
E
D
C
2
1
3
1
4
2
Q
N
A
Q
B
1
3
2
E

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
©2015 Symmons Industries, Inc. ■www.symmons.com ■[email protected] ■ZV-3077 REV B ■ 020315
Temperature Control Diverter Control
Operation & Maintenance
Troubleshooting Chart
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
1) Turn shower handle counterclockwise approximately
1/4 turn to put valve in cold position.
2) Turn shower handle counterclockwise approximately
1/2 turn to put valve in warm position.
3) Turn shower handle counterclockwise approximately
3/4 turn to put valve in hot position.
1) Turn diverter left for tub spout operation.
2) Turn diverter right for hand shower operation.