Synapse DIM10-100-00 User manual

ORDERING INFORMATION
Part Number: DIM10-100-00
FEATURES
• True ON/OFF switching via relay, up to 2A load
• 0-10V dimming, up to 10mA source/sink
• Pushbutton terminal blocks for easy installation
RATINGS
Voltage Input: 100-277 VAC (+/-10%), 50/60 Hz
Voltage Output (Max): 305V
Power Consumption (No Load): 0.3W @ 277VAC;
0.5W @ 120VAC
DESCRIPTION
The Synapse DIM10-100-00 controls LED lighting in
commercial and industrial buildings using the SNAP
wireless mesh network. It uses an internal relay
to provide True On/O capability, and it provides
0-10V analog dimming control using a true On/O
0-10V standard dimming protocol. Synapse lighting
controllers can be controlled with a browser-based
application available with the Synapse SimplySNAP
lighting solution.
SPECIFICATIONS
Relay Max Switched Circuit: Zero Cross, 2A
Dim Control Max Load: 10 mA Source/Sink
Radio Frequency: 2.4 GHz (IEEE 802.15.4)
RF Transmission Output Power: +20dBM
Operating Temperature: -20 to +60 C
Operating Humidity: 10 to 90%, non-condensing
Dimensions: 7.1”L x 1.8”W X 1”H (181 X 46 X 26 mm)
Enclosure Type: Galvanneal steel
Configuration/Programming: Stored in non-volatile
memory
INSTALLATION
CAUTION
• DIM10-100-00 controllers must be installed
in accordance with national, state, and local
electrical codes and requirements
• All work must be performed by qualified
personnel
• Disconnect all power before installation or
service
• Metal conduit connector must be grounded
• The switched output (LOAD) is energized by
default at power up
Needed Materials
Wiring Connectors: All existing wiring connectors
must be replaced with new UL listed wiring
connectors. All wiring connectors must be correctly
sized for the application and the number and the
size of the electrical conductors.
Mounting: Secure with four #8 screws. See the
DIM10-100-00 mounting template for assistance.
Mounting Options: Mount in an LED Fixture or
a Troer. See figure 1 below for proper antenna
orientation.
Installation Instructions
1. WARNING: TO AVOID FIRE, SHOCK, OR
DEATH: TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND VERIFY THAT
POWER IS OFF BEFORE WIRING!
2. Place DIM10-100-00 in desired location and
secure it using #8 screws or other appropriate
methods. Prior to permanently mounting the
DIM10-100-00, make sure the antenna points
directly upward or downward and is free of
any metal objects within 12 in. of the antenna.
(Figure 1)
Note: When installing the DIM10-100-00 into an
enclosure, consideration of antenna position and
interference is required in order to provide the most
optimum wireless signal strength.
FIGURE 1  ANTENNA ORIENTATION
3. Disconnect the hot wire (black) from the LED
fixture and connect it to the LINE input on the
DIM10-100-00.
4. Connect the black wire of the LED fixture to the
LOAD output on the DIM10-100-00.
5. Connect the white wire (neutral) of the LED
DIM10-100-00
Load Ratings: 2A @ 100-277VAC (+/- 10%)
Installation Guide
WARNING AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes
and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
WARNINGS AND CAUTIONS:
• Disconnect power at circuit breaker or fuse when servicing, installing or
removing fixture or changing lamps.
• Risk of Electric Shock - More than one disconnect switch may be required to
de-energize the equipment before servicing. Use this device with copper or
copper clad wire only.
DO
DON’T
This Way Up
116-081509-004-A003

fixture to the NEUTRAL input on the DIM10-100-
00.
6. Connect the white wire (neutral) from the LED
fixture to the electrical service white wire/
neutral.
Note: Steps 7-10 are for Class 1/2 Dimming Control
7. Connect the DIM- wire on the LED fixture to the
DIM- input on the DIM10-100-00.
8. Connect the DIM+ wire on the LED fixture to the
DIM+ input on the DIM10-100-00.
9. Switch power on to the fixture. The light should
turn on. Note: When switched on, lamps should
turn on to full brightness; approximately 10 VDC
signal on the DIM+ wire using the DIM- wire as
reference.
10. Refer to the SimplySNAP User’s Manual for
information on provisioning the DIM10-100-00.
FIGURE 2  WIRING DIAGRAM
Dimming
Below are some recommendations for successful
dimming using the DIM10-100-00. The dimming
control wires are referenced as Dim+ and Dim-. The
dimming signals have a Maximum voltage of 10V DC.
• Use multi-strand 18 Gauge Wire for noise
immunity and current capability
• Do not ground the dimming wire. This is a return
signal and is critical for dimming.
• Route dimming wires away from AC lines if
possible.
• Use connections with properly sized connectors.
• Eliminate excess wire between fixtures. Line
length will cause voltage drop.
• Number of fixtures that can be daisy-chained is
dependent upon the following factors: dimming
current, current requirements for LED driver,
length of wire, quality of connection, and gauge
of wire
• Verify dimming capability via a “test bed” with
the number of actual fixtures, wire length,
connectors, and wire gauge
Regulatory Information and Certifications
RF Exposure Statement: This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated
with minimum distance of 20cm between the radiator and your
body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Industry Canada (IC) certifications: This digital apparatus does
not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of
the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits
radioelectriques depassant les limites applicable aux appareils
numeriques de la class B prescrites dans le Reglement sur
le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
FCC certifications and regulatory information (USA only)
FCC Part 15 Class B: This device complies with part 15 of the
FCC rules. Operation is subject to the following two conditions:
(1) These devices may not cause harmful interference, and (2)
These devices must accept any interference received, including
interference that may cause harmful operation.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This
equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more
of the following measures: (1) Re-orient or relocate the receiving
antenna; (2) Increase the separation between the equipment and
the receiver; (3) Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected; (4) Consult
the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse
Wireless, Inc. declares that the product name “DIM10-100-00” to
which this declaration relates, meet the requirements specified
by the Federal Communications Commission as detailed in the
following specifications:
• Part 15, Subpart B, for Class B equipment
• FCC 96-208 as it applies to Class B personal computers and
peripherals
• This product has been tested at an External Test Laboratory
certified per FCC rules and has been found to meet the FCC, Part
15, Emission Limits. Documentation is on file and available from
Synapse Wireless, Inc.
If the FCC ID for the module inside this product enclosure is not
visible when installed inside another device, then the outside of
the device into which this product is installed must also display a
label referring to the enclosed module FCC ID. Modifications (FCC
15.21): Changes or modifications to this equipment not expressly
approved by Synapse Wireless, Inc., may void the user’s authority
to operate this equipment.
CERTIFICATIONS
Model #: DIM10-100-00
UL File No: E346690
Contains FCC ID: U9O-SM220 and IC: 7084A-
SM220
LED Driver
DIM10-100-00
Violet
Gray
White
Black
White
Black
Dim+
Dim-
Blue
NEUTRAL
LINE
LOAD
EARTH GND
ANTENNA
1-10V
COMMON
NEUTRAL
LINE