Synapse DIM10-087-06-F3W User manual

21-D08706F3W-INS A-5
SPECIFICATIONS
 Dim Control Max Load: 10 mA Source/Sink
 Radio Frequency: 2.4 GHz (IEEE 802.15.4)
 RF Transmission Output Power: +20 dBm
 Operating Temperature: -40 to +80 C
 Operating Humidity: 10 to 90%, non-condensing
 Wire Size: 18 AWG, 8” Wires, UL1316, 600V
 Dimensions: 2.25” L x 2.0” W x .3” H
(57 x 50.8 x 7.6 mm)
DESIGN CONSIDERATIONS
Below are some recommendations for successful
dimming using the DIM10-087-06-F3W. The dimming
control wires are referenced as DIM+ and DIM-. The
dimming signals have a Maximum voltage of 10V DC.
 Do not ground the DIM- wire to chassis ground;
this is a return signal and is critical for proper
dimming.
 Route dimming wires away from AC lines if
possible.
 Maximum 0f 8 DIM to OFF LED Drivers.
 Do not mount to a heatsink or to a LED driver.
 When installing the DIM10-087-06-F3W into an
enclosure, consideration of the internal antenna
position and any possible interference is required
to provide the best wireless signal strength. Prior
to permanently mounting it, make sure the device
is free of any metal objects within 2 inches.
NOTE: LED Driver must support DIM to OFF functionality.
NEEDED MATERIAL
 Mounting Hardware: (1) #4 or M3 screws and
standoff recommended
INSTALLATION INSTRUCTIONS
MOUNTING
1.
Place the controller in desired location and secure
it using #4 sized screw and standoff using the
mounting hole located in the center of the board.
Note: For the best RF signal propagation, mount
the controller so that the bottom is facing the
ground.
WIRING THE DIM10-087-06-F3W
CONTROLLER
2.
Connect the POWER (BROWN) wire of the DIM10-
087-06-F3W to the 12-24V DC Aux output from
the LED driver.
3.
Connect the DIM+ (PURPLE) wire from the DIM10-
087-06-F3W to the DIM+ wire on the LED driver.
4.
Connect the DIM- (PINK/WHITE STRIPE) wire from
the DIM10-087-06-F3W to the COMMON/DIM- wire
on the LED driver.
(See Figure 1 on page 2)
POWERING UP THE FIXTURE AND
CONTROLLER
After connecting the Controller to the LED Driver,
switch power on to the fixture. The light should turn
on.
Note: When the controller is powered, the
following colors indicate the status.

Red = No Network Found (Communication Lost)

Blinking Green = Network Found, Controller Not
Configured (Device not yet added to SimplySnap)

Green = Network Found, Controller Configured
(Normal Operation)
For more information on SimplySnap and the DIM10-
087-06-F3W, refer to the website at
http://help.synapsewireless.com/.
DIM10-087-06-F3W Controller
Load Ratings: 12 to 24VDC, +/-10%, 900mW max
Operating Humidity: 10 to 90%, non
-
condensing
WARNING AND CAUTIONS:
 TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER AT CIRCUIT BREAKER
OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING!
 PROPER GROUNDING REQUIRED TO AVOID STATIC DISCHARGE WHICH
CAN DAMAGE CONTROLLERS DURING INSTALLATION.
INSTALLATION GUIDE
WARNING AND CAUTIONS:
 If you are unsure about any part of these instructions, consult an electrician; all
work should be performed by qualified personnel.
 DIM10-087-06-F3W controllers must be installed in accordance with national, state,
and local electrical codes and requirements.
S
TATUS LED

21-D08706F3W-INS A-5
REGULATORY INFORMATION AND
CERTIFICATIONS
RF Exposure Statement: This equipment complies
with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be
installed and operated with minimum distance of 20cm
between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with
any other antenna or transmitter.
Industry Canada (IC) certifications: This digital
apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian
Department of Communications.
Le present appareil numerique n’emet pas de bruits
radioelectriques depassant les limites applicable aux
appareils numeriques de la class B prescrites dans le
Reglement sur le brouillage radioelectrique edicte par
le ministere des Communications du Canada.
FCC certifications and regulatory information
(USA only)
FCC Part 15 Class B: This device complies with part
15 of the FCC rules. Operation is subject to the
following two conditions: (1) These devices may not
cause harmful interference, and (2) These devices
must accept any interference received, including
interference that may cause harmful operation.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC
15.105): This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
(1) Re-orient or relocate the receiving antenna; (2)
Increase the separation between the equipment and
the receiver; (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is
connected; (4) Consult the dealer or an experienced
radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19):
Synapse Wireless, Inc. declares that the product name
“DIM10-087-06-F3W” to which this declaration relates,
meet the requirements specified by the Federal
Communications Commission as detailed in the
following specifications:
• Part 15, Subpart B, for Class B equipment
• FCC 96-208 as it applies to Class B personal
computers and peripherals
• This product has been tested at an External Test
Laboratory certified per FCC rules and has been found
to meet the FCC, Part 15, Emission Limits.
Documentation is on file and available from Synapse
Wireless, Inc.
If the FCC ID for the module inside this product
enclosure is not visible when installed inside another
device, then the outside of the device into which this
product is installed must also display a label referring
to the enclosed module FCC ID. Modifications (FCC
15.21): Changes or modifications to this equipment not
expressly approved by Synapse Wireless, Inc., may
void the user’s authority to operate this equipment.
CERTIFICATIONS
Model : DIM10-087-06-F3W
Contains FCC ID : U9O-SM220
Contains IC : 7084A-SM220
UL File No : E346690
DALI-2 Certified Application Controller
CE
UKCA
Contact Synapse for Support- [phone]
Figure 1 - DIM to OFF Wiring Diagram
WARNING:
· If a single Synapse controller is used to drive the DIM+ input of
multiple LED drivers, then all of the DIM- lines from all drivers
MUST be directly tied/shorted together to provide a common
return/ground to the controller.
· Synapse will not warranty or be liable for designs with any other
electronic means of coupling DIM- lines from multiple drivers.
Patented
–
virtual marking at
https://www.synapsewireless.com/about/patents