Synapse TL7-HVG User manual

DOC-1000496-A-4
SPECIFICATIONS
•Relay Max Switch Circuit:
o5A @ 110-277VAC (+/- 10%)
o3A @ 347VAC (+/- 10%)
o2A @ 480VAC (+/- 10%)
•Dim Control Max Load: 20mA
•Radio Frequency: 2.4 GHz (IEEE 802.15.4)
•RF Transmission Output Power: +20dBM
•Operating Temperature: -40 to +70 C
•Operating Humidity: 0 to 90%, non-condensing
•Dimensions: 3.3” D x 3.9” H
(84mm D x 98mm H)
•Surge Protection: 6kV
•Sensor Input: 24V
•Sensor Power Max Load: 24VDC, 50mA peak and
20mA continuous
CAUTION
•This product must be installed in accordance with
national, state, and local electrical codes and
requirements
•All work must be performed by qualified personnel
•Disconnect all power before installation or service
WIRING DETAILS OF C136.41 SOCKET
WARNING: TO AVOID FIRE, SHOCK, OR DEATH:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE
AND VERIFY THAT POWER IS OFF BEFORE WIRING!
If a motion sensor or the C136.41 socket needs to be
wired up prior to installing the TL7-HVG, please refer
to the wiring details.
(See Figure 1)
Figure 1 –C136-41 Socket Wiring Details
WARNING AND CAUTIONS:
•TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING!
•The TL7-HVG should only be installed in a fixture with a NEMA/ANSI C136.41 receptacle.
•Device is rated up to 6kV surge, take steps to install an external surge protector for
additional protection.
•Failure to follow these instructions and warnings could potentially void warranty.
TL7-HVG Lighting Controller
Load Rating: 110-480VAC ±10%
WARNING AND CAUTIONS:
•To be installed and/or used in accordance with appropriate electrical codes and
regulations.
•If you are unsure about any part of these instructions, consult an electrician; all work
should be performed by qualified personnel.
•Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture
or changing lamps.
INSTALLATION GUIDE
WARNING:
· If a single Synapse controller is used to drive the DIM+ input of multiple LED drivers, then all of the DIM- lines
from all drivers MUST be directly tied/shorted together to provide a common return/ground to the controller.
· Synapse will not warranty or be liable for designs with any other electronic means of coupling DIM- lines from
multiple drivers.

DOC-1000496-A-4
INSTALLATION INSTRUCTIONS
WARNING: TO AVOID FIRE, SHOCK, OR DEATH:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE
AND VERIFY THAT POWER IS OFF BEFORE WIRING!
1. If applicable, remove the lighting control device
currently installed in the fixture receptacle.
2. Align the TL7-HVG such that the large contact pin
is positioned above the large receptacle contact.
3. Insert the TL7-HVG contacts completely into the
receptacle contacts by pressing down.
4. While pressing down, twist the TL7-HVG housing
clockwise until it locks into place. (See Figure 2)
5. If the device is properly seated, on power up (and
until commissioned in a SimplySnap system), the
TL7-HVG will immediately go to 100% dimming,
then fade to 0% over 60 seconds, then back to
100%. If it does not dim, the device is not twisted
into the proper position.
Note: To fuction properly, make sure the controller is
inserted completely into the socket and twisted into the
locked position.
STATUS LEDS
LED
COLOR
STATUS
LED 1
BLUE
Network Found, Controller Not
Configured (Not yet added to
SimplySnap)
LED 1
GREEN
Network Found, Controller
Configured (Normal Operation)
LED 1
RED
No Network Found
(Communication Lost)
LED 2
GREEN
Relay closed
LED 2
OFF
Relay open
REGULATORY INFORMATION AND
CERTIFICATIONS
RF Exposure Statement: This equipment complies
with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be
installed and operated with minimum distance of 20cm
between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with
any other antenna or transmitter.
Industry Canada (IC) certifications: This digital
apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian
Department of Communications.
Le present appareil numerique n’emet pas de bruits
radioelectriques depassant les limites applicable aux
appareils numeriques de la class B prescrites dans le
Reglement sur le brouillage radioelectrique edicte par
le ministere des Communications du Canada.
FCC certifications and regulatory information (USA
only)
FCC Part 15 Class B: This device complies with part
15 of the FCC rules. Operation is subject to the
following two conditions: (1) These devices may not
cause harmful interference, and (2) These devices
must accept any interference received, including
interference that may cause harmful operation.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC
15.105): This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
(1) Re-orient or relocate the receiving antenna; (2)
Increase the separation between the equipment and
the receiver; (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is
connected; (4) Consult the dealer or an experienced
radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19):
Synapse Wireless, Inc. declares that the product name
“TL7-HVG” to which this declaration relates, meet the
requirements specified by the Federal Communications
Commission as detailed in the following specifications:
•Part 15, Subpart B, for Class B equipment
•FCC 96-208 as it applies to Class B personal
computers and peripherals
•This product has been tested at an External
Test Laboratory certified per FCC rules and
has been found to meet the FCC, Part 15,
Emission Limits. Documentation is on file and
available from Synapse Wireless, Inc.
If the FCC ID for the module inside this product
enclosure is not visible when installed inside another
device, then the outside of the device into which this
product is installed must also display a label referring
to the enclosed module FCC ID. Modifications (FCC
15.21): Changes or modifications to this equipment not
expressly approved by Synapse Wireless, Inc., may
void the user’s authority to operate this equipment.
CERTIFICATIONS
Model : TL7-HVG
Contains FCC ID: U9O-SM220
Contains IC : 7084A-SM220
UL File No : E493550
Contact Synapse for Support- [phone]
Patented –virtual marking at
https://www.synapsewireless.com/about/patents
Figure 2 –Installation Diagram