Synergy E5 User manual

w w w .s y n e r g y r c h e lic o p t e r s .c o m

w w w .s y n e r g y r c h e lic o p t e r s .c o m

103-256 M2.5 Flat Head Cross Recess
305-102 CF Lower Frame Brace
305-101 E5 Frame Spacer
103-256 M2.5 Flat Head Cross Recess
305-103 E5 CF Gyro Mount Plate
305-101 E5 Frame Spacer
Lower Frame Brace Assembly
Page 1
Gyro Mount Plate Assembly
WWW.SYNERGYRCHELICOPTERS.COM

108-105 - 10x19x5 Radial Bearing
108-105 - 10x19x5 Radial Bearing
305-104 E5 Third Main Shaft Bearing Block
305-124 E5 Main Shaft Bearing Block
Main Shaft Bearing Block Assembly
*** Note ***
Observe orientation of bearing blocks
Page 2
WWW.SYNERGYRCHELICOPTERS.COM

Front Tail Transmission Assembly
108-124 12x18x4 Radial Bearing
320-301 Front Mushroom Gear Bearing Block
320-218 18T Front Trans Mushroom Gear
100-351 M3 Nylock Nut
100-372 M3x12 Set Screw
100-354 M3 Washer
108-510 5x10x4 Radial Bearing
320-302 Bevel Gear Top Bearing Block
320-406 11mm Pin for 18T Bevel Gear
320-303 Spur Gear Bottom Bearing Block
108-593 5x9x3 Radial Bearing
320-408 Spur Gear Shaft
305-213 13T Spur Gear
320-407 2mm Spur Gear Pin
320-101 TranSupport CF Plate
305-105 E5 TranSupport Standoff
101-306 M3x6 Button Head x12
100-372 M3x12 Set Screw
Important! - TIghten and
secure set screw with loctite.
This set screw secures bevel
gear pin.
Page 3
320-118 Front Trans Bevel Gear
IMPORTANT! - Any screw which is metal to metal needs loctite! Clean oil from bolts and apply blue loctite.
WWW.SYNERGYRCHELICOPTERS.COM

305-121 Key Chain Canopy Mount, Female 21mm
305-106 Break-away Plate
101-306 M3x6 Button Head
X2
Front Canopy Mounts (21mm)
101-306 M3x6 Button Head
305-117 Key Chain Canopy Mount, Female 17mm
305-106 Break-away Plate
Key Chain Style Canopy Mounts
X2
Rear Canopy Mounts (17mm)
Page 4
WWW.SYNERGYRCHELICOPTERS.COM

103-256 M2.5 Flat Head Cross Recess
305-101 E5 Frame Spacer
305-107 Front Battery Plate
Front Battery Plate
Page 5
WWW.SYNERGYRCHELICOPTERS.COM

103-256 M2.5 Flat Head Cross Recess
305-101 E5 Frame Spacer
305-108 E5 Rear Battery Plate
Rear Battery Plate
Page 6
WWW.SYNERGYRCHELICOPTERS.COM

103-256 M2.5 Flat Head Cross Recess
305-101 E5 Frame Spacer
305-109 E5 ESC Mount Plate
ESC Mount Plate
Page 7
WWW.SYNERGYRCHELICOPTERS.COM

101-306 M3x6 Button Head
100-310 M3x10 Socket Head
305-111 E5 Main Boom Clamp
305-110 E5 Radio Plate
Main Boom Clamps and Radio Plate
Note - Bolts engaged in pinching mechanism do not require loctite
Page 8
WWW.SYNERGYRCHELICOPTERS.COM

100-306 M3x6 Socket Head x8
100-308 M3x8 Socket Head
Left Frame - Main Shaft Bearing Blocks - Install
ATTENTION!
DO NOT FULLY TIGHTEN BOLTS YET!!
Note - Third Main Shaft Bearing Block is adjustable fore and aft
to provide for correct main shaft alignment.
Note - Pay attention to bearing block orientation!
305-118 E5 Main Frame CF
Page 9
WWW.SYNERGYRCHELICOPTERS.COM

Battery Plate - Install
101-306 M3x6 Button Head
NOTE - DO NOT FULLY TIGHTEN BOLTS YET!
Page 10
WWW.SYNERGYRCHELICOPTERS.COM

101-306 M3x6 Button Head
NOTE - DO NOT FULLY TIGHTEN BOLTS
Gyro Plate and Lower X Brace - Install
Page 11
WWW.SYNERGYRCHELICOPTERS.COM

101-306 M3x6 Button Head
Front Tail Transmission Install
NOTE - DO NOT TIGHTEN BOLTS FULLY YET!
**IMPORTANT PLEASE READ**
Frames are slotted for optional tail gear ratios
Tail Transmission was designed to slide
fore and aft to allow for 4.0:1 gear ratio
as well as optional 4.5:1 tail ratio.
4.0:1(stock)Slide Transmission all the way FORWARD
4.5:1(optional)Slide Transmission all the way AFT
4.0:1 = 52T / 13T (Stock)
4.5:1 = 54T / 12T (Optional)
Page 12
WWW.SYNERGYRCHELICOPTERS.COM

Main Boom Clamp and Radio Plate Install
100-306 M3x6 Socket Head Bolt
Page 13
WWW.SYNERGYRCHELICOPTERS.COM

305-112 Elevator Tail Servo Mount
High Quality Digital 760us Tail Servo (Not Included)
Recommended - Futaba BLS256
100-268 M2.5x8 Socket Head
106-115 Servo Hold Down
107-104 Pivot Ball 2mm
100-252 M2 Nylock Nut
Note - Servo horn will need to be trimmed
in order to avoid interference with gyro
sensor mount.
Important - Pivot ball should be located at
16mm from center of servo horn. This is important
for proper servo resolution.
Tail Servo Mount
Page 14
WWW.SYNERGYRCHELICOPTERS.COM

100-266 M2.5x6 Socket Head
Tail Servo Install
Page 15
WWW.SYNERGYRCHELICOPTERS.COM

Canopy Mount Install - Left Frame Side
101-310 M3x10 Button Head
100-351 M3 Nylock Nut
21mm Front Canopy Mount
See Page 4
17mm Rear Canopy Mount Assembly
See Page 4
Note - Button Head fits into large frame hole, mounts will fit flush against frame.
305-101 E5 Frame Spacer
101-306 M3x6 Button Head
Page 16
WWW.SYNERGYRCHELICOPTERS.COM

100-351 M3 Nylock Nut
305-118 E5 Main Frame CF
Page 17
WWW.SYNERGYRCHELICOPTERS.COM
Right Frame Canopy Mount Install

Elevator Servo Mounting
100-268 M2.5x8 Socket Head
100-266 M2.5x6 Socket Head
106-115 Servo Hold Down x2
305-112 Elevator-Tail Servo Mount X2
Page 18
WWW.SYNERGYRCHELICOPTERS.COM