Synology FlashStation FS1018 Manual

Synology FlashStation FS1018
Hardware Installation Guide

Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology FlashStation at a Glance 4
Safety Instructions 5
Chapter 2: Hardware Setup
Tools and Parts for Drive Installation 6
Install Drives 6
Start Up Your FlashStation 9
Add a RAM Module on FlashStation 10
Attach M2D17 Adapter Card to FlashStation 12
Add a Network Interface Card 14
Replace System Fan 16
Chapter 3: Install DSM on FlashStation
Install DSM with Web Assistant 19
Learn More 19
Appendix A: Specications
Appendix B: LED Indicator Table
Synology_HIG_FS1018_20170515
2

Thank you for purchasing this Synology product! Before setting up your new FlashStation, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your FlashStation.
Note: All images below are for illustrative purposes only, and may di󰀨er from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
RJ-45 LAN cable x 2
Hard drive tray key x 2
Before You Start 1
Chapter
3
3

4Chapter 1: Before You Start
Synology FlashStation at a Glance
No. Article Name Location Description
1 Status Indicator
Front
Displays the status of the system. For more information, see "Appendix B:
LED Indicator Table".
2 Alert Indicator Displays warnings regarding fan or temperature. For more information, see
"Appendix B: LED Indicator Table".
3 Power Button
1. Press to power on the FlashStation.
2. To power o󰀨 the FlashStation, press and hold until you hear a beep sound
and the Power LED starts blinking.
4 LAN Indicator Displays the status of the network connection. For more information, see
"Appendix B: LED Indicator Table".
5 Drive Status Indicator Displays the status of the installed drive. For more information, see
"Appendix B: LED Indicator Table".
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Front USB 3.0 Port Connect external drives or other USB devices to the FlashStation here.
8 Drive Tray Lock Lock or unlock drive trays.
9 Power Port
Back
Connect the AC power cord here.
10 Fan Disposes of excess heat and cools the system. If the fan malfunctions, the
FlashStation will emit a beeping sound.
11 PCI Express
Expansion Slot Supports one PCIe x8 slot (x8 link) add-on card.
12 Kensington
Security Slot Attach a Kensington security lock here.
13 LAN Port Connect network cables here.
14 RESET Button
1. Press and hold until you hear a beep sound to restore the default IP
address, DNS server, and password for the admin account.
2. Press and hold until you hear a beep sound, then press and hold again
until you hear three beep sounds to return the FlashStation to “Not
Installed” status so that DiskStation Manager (DSM) can be reinstalled.
15 Rear USB 3.0 Port Connect external drives or other USB devices to the FlashStation here.
16 Expansion Port Connect Synology Expansion Unit1to the FlashStation here.
1For more information about Synology Expansion Unit supported by your FlashStation, please visit www.synology.com.

5Chapter 1: Before You Start
Safety Instructions
Keep away from direct sunlight and away from chemicals. Make sure the environment does not
experience abrupt changes in temperature or humidity.
Place the product right side up at all times.
Do not place near any liquids.
Before cleaning, unplug the power cord. Wipe with damp paper towels. Do not use chemical or
aerosol cleaners.
To prevent the unit from falling over, do not place on carts or any unstable surfaces.
The power cord must plug in to the correct supply voltage. Make sure that the supplied AC voltage is
correct and stable.
To remove all electrical current from the device, ensure that all power cords are disconnected from
the power source.
Risk of explosion if battery is replaced with an incorrect type. Dispose of used batteries appropriately.

Tools and Parts for Drive Installation
• At least one 2.5” SATA drive (please visit www.synology.com for compatible drive models.)
Warning: If you install a drive that contains data, the system will format the drive and erase all existing data. Please
back up any important data before installation.
Install Drives
1 Press the right part of a drive tray to pop out the handle, and then pull the drive tray handle in the direction as
indicated below to remove the drive tray.
2 Load a drive in each drive tray.
Hardware Setup
6
2
Chapter

7Chapter 2: Hardware Setup
3 Insert the loaded drive tray into the empty drive bay, and press the handle in ush with the front panel to hold
the drive tray in place.
Note: Make sure the tray is pushed in all the way. Otherwise, the drive might not function properly.
4 Insert the drive tray key into the drive tray lock, turn the key clockwise (to the "–" position) to lock the handle of
the drive tray, and then remove the key.
5 Repeat the steps above to assemble the other drives you have prepared.

8Chapter 2: Hardware Setup
6 Drives are numbered as shown below.
Note: If you want to create a RAID volume, we recommend that all installed drives are of the same size to make the
best use of drive capacity.

9Chapter 2: Hardware Setup
Start Up Your FlashStation
1 Use the LAN cable to connect the FlashStation to your switch, router or hub.
2 Connect one end of the AC power cord to the power port of the FlashStation, and the other to the power outlet.
3 Press the power button.
Congratulations! Your FlashStation is now online and detectable from a network computer.

10 Chapter 2: Hardware Setup
Add a RAM Module on FlashStation
The optional Synology DDR4 RAM module is designed for FlashStation memory expansion. Follow the steps
below to install, check, or remove a RAM module on your FlashStation.
To install the RAM module:
1 Shut down your FlashStation. Disconnect all cables connected to your FlashStation to prevent any possible
damages.
2 The RAM modules are located at the bottom of FS1018.
3 Remove the 2 screws that secure the bottom lid. Lift o󰀨 the lid and place it to the side. You will see one 8GB
module pre-installed.
Important: When you remove the lid, you expose sensitive internal components. Avoid touching anything other than
the memory assembly when you remove or add memory.
4 Insert the new memory module in the slot:
a Align the notch on the gold edge of the module with the notch in the lower memory slot.
b Tilt the card and insert the module into the slot. Make sure the module is properly inserted.
c Push down on the memory module with moderate pressure until you hear a click.
d correctl
Important: Hold the memory module by its edges, and do not touch the golden connectors.
Note: Synology o󰀨ers RAM modules1for memory upgrade. For more information, please visit www.synology.com/
products/Synology_RAM_Module.
5 Replace the bottom lid. Replace and tighten the 2 screws you removed in step 3.
6 Reconnect the cables you removed in step 1, and then press and hold the power button to turn on your
FlashStation.
1Synology will not provide complete product warranty or technical support if non-Synology RAM modules are used for memory upgrade.

11 Chapter 2: Hardware Setup
To make sure FlashStation recognizes the new memory capacity:
1 Install DiskStation Manager (DSM). (See the next chapter for more information.)
2 Log in to DSM as admin or a user belonging to the administrators group.
3 Check Total Physical Memory in Control Panel > Info Center.
If your FlashStation does not recognize the memory or does not start up successfully, conrm that the memory is
installed correctly.
To remove the RAM Module:
1 Follow step 1 and 2 of the "To install the RAM module" section to shut down your FlashStation, disconnect the
cables, and then remove the bottom lid.
2 Push the levers on both sides of the memory module outwards. The module will be released from the slot.
3 Hold the memory module by its notches and remove it from the slot.
4 Replace the bottom lid. Replace and tighten the screws removed in step 1.
5 Reconnect the cables removed in step 1. Now, you may turn on your FlashStation.

12 Chapter 2: Hardware Setup
Attach M2D17 Adapter Card to FlashStation
Your FlashStation supports one M2D17 adapter card. To replace the long bracket with the M2D17 adapter card,
please follow the instructions below.
To install the M2D17 adapter card:
1 Shut down your FlashStation and disconnect all cables from your FlashStation to prevent any possible
damages.
2 Remove the 6 screws that secure the main unit, and then pull the top cover in the direction as illustrated below.
3 Add M.2 SSD to M2D17 adapter card:
a Insert M.2 SSD into the slot. Make sure the card is fully inserted.
b Tighten the SSD with a screw.
c Repeat previous two steps if installing another optional SSD is needed. Slot numbereds are shown as below.

13 Chapter 2: Hardware Setup
4 Install the M2D17 adapter card:
a Remove the screw that secures the adapter slot’s cover.
b Remove the adapter slot’s cover.
c Align the card’s connectors with the adapter slot, and insert the card into the slot.
d Put back and fasten the screw that you removed in step 4-a so as to secure the newly inserted card.
5 Put back the upper case removed in step 2 and tighten the srcews.
1For more information about supported 10GbE or Gigabit network interface cards, please visit www.synology.com.

14 Chapter 2: Hardware Setup
Add a Network Interface Card
Your FlashStation has a PCI Express expansion slot which allows you to install 10GbE or Gigabit network
interface card for LAN port expansion.1
To install a network interface card:
1 Press and hold the power button until you hear a beep sound to shut down your FlashStation. Disconnect all
cables from your FlashStation to prevent any possible damage.
2 Remove the 6 screws that secure the main unit, and then pull the top cover in the direction as illustrated below.
3 Remove the expansion slot shield:
a Remove the screw that secures the adapter slot’s cover.
b Remove the adapter slot’s cover.

15 Chapter 2: Hardware Setup
4 Install the network interface card:
a Align the card’s connectors with the adapter slot, and insert the card into the slot.
b Use two ngers with rm, even pressure to push down on the card and the bracket.
5 Replace the top cover, and then replace and tighten the 6 screws you removed in Step 2.

16 Chapter 2: Hardware Setup
Replace System Fan
Your FlashStation will beep if either of the system fans is not working. Follow the steps below to replace the
malfunctioning fan with a good one.
To replace the system fan:
1 Shut down your FlashStation and disconnect all cables to prevent any possible damages.
2 Fans are numbered as follows:
3 Remove the 4 screws that secure the fan panel.
Note: Make sure the connectors are fully inserted. Otherwise, the network interface card might not be able to
function properly.

17 Chapter 2: Hardware Setup
4 Remove the malfunctioning fan:
a Pull the fan panel out of your FlashStation.
b Disconnect the 2 fan cables from the connectors located near the bottom of the fan socket, and then remove
the fan panel.
c Remove the 4 screws that secure the malfunctioning fan, and then remove the fan.

18 Chapter 2: Hardware Setup
5 Install the new fan:
a Replace the malfunctioning fan with a good one (with the fan cable within the fan pointing at the bottom-left
corner), and then tighten the 4 screws to secure the new fan.
b Connect the 2 fan cables to the connectors located near the bottom of the fan socket, and then replace the
fan panel.
6 Replace and tighten the 4 screws you removed in step 3.
7 Reconnect the cables you removed in step 1, and then press and hold the power button to turn on your
FlashStation.

After hardware setup is nished, please install DiskStation Manager (DSM) – Synology’s web-based operating
system – on your FlashStation.
Install DSM with Web Assistant
Your FlashStation comes with a built-in tool called Web Assistant that helps you download the latest version of
DSM from the Internet and install it on your FlashStation. To use Web Assistant, please follow the steps below.
1 Power on the FlashStation.
2 Open a web browser on a computer connected to the same network as the FlashStation.
3 Enter either of the following into the address bar of your browser:
a nd.synology.com
b ashstation:5000
4 Web Assistant will be launched in your web browser. It will search for and nd the FlashStation within the local
network. The status of the FlashStation should be Not installed.
5 Click Connect to start the setup process and follow the onscreen instructions.
Note:
1. The FlashStation must be connected to the Internet to install DSM with Web Assistant.
2. Suggested browsers: Chrome, Firefox.
3. Both the FlashStation and the computer must be in the same local network.
Learn More
Congratulations! Your FlashStation is now ready for action. For more information or online resources about your
FlashStation, please visit www.synology.com.
Install DSM on FlashStation 3
19
Chapter

Item FS1018
Internal Drives 2.5” SATA x 12
Maximum Internal Raw
Capacity
• 48 TB (12 x 4 TB)
• 288TB with DX1215 (expansion unit) x 2
External Device Ports • USB 3.0 x 3
• Expansion port x 2
LAN Ports Gigabit x 4
PCIe Slot PCIe x8 slot (x8 mode) add-on card (optional)
Size (H x W x D) (mm) 166 x 282 x 243
Weight (kg) 5.2
Supported Clients • Windows 7 and 10
• Mac OS X 10.10 onward
File Systems • Internal: Btrfs, ext4
• External: Btrfs, ext4, ext3, FAT, NTFS, HFS+, exFAT1
Supported RAID Types • Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • RAID F1
Agency Certications • FCC Class B • CE Class B • BSMI Class B
HDD Hibernation Yes
Scheduled Power On/O󰀨 Yes
Wake on LAN Yes
Language Localization
Environment Requirements
• Line voltage: 100V to 240V AC
• Frequency: 50/60Hz
• Operating Temperature: 40 to 104˚F (5 to 40˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
Specications A
20
Appendix
1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.