Taco Marine NEPTUNE II Datasheet

NEPTUNE II
L10-1003
INSTALLATION INSTRUCTION GUIDE
TACO Marine® Leaning Posts
®

2 / NEPTUNE II
L10-1003
Thank you for purchasing the Neptune II Leaning Post! As a family-owned
and operated business since 1959, we take pride in oering the highest-
quality products with excellent customer service. We stand behind our
products 100 percent. If you have any questions about this mount or
installation, please contact us by visiting tacomarine.com/contactus.
•PHILLIPS HEAD SCREWDRIVER OR SCREW
GUN
•ADJUSTABLE WRENCH
•WAX AND LEAD PENCIL
•DRILL
•JIG SAW
•MARINE-GRADE SEALANT
•24" X 54" MARINE LUMBER
Required*
*not included
Kit Contents
ITEM QTY DESCRIPTION
A 1 D-ring
B 1 Rod holder rack
C 2 Side frame
D 1 Crossbar
E 2 Hinge
F 4 Footrest
G 1 Cooler strap
H 4 Eye strap
I 1 Seat Cushion
J 1 Tackle storage bag
(sold separately)
1 6 Button Head Socket Cap Screw,
1/4" - 20 x 1"L
2 4 Flat Head Socket Cap Screw,
1/4" - 20 x 3/4"L
3 16 Oval Head Phillips Sheet Metal Screw,
#14 x 1-1/4"L
4 4 Flat Head Phillips Sheet Machine Screw,
#10 - 32 x 3/8"L
5 12 Nylon Nut,
1/4" - 20 5/16"H
6 16 Washer,
.65"OD, .27"ID, .039"H
7 2 Spacer,
1/2"OD, 1/4"ID, 1/8"H
8 1 Hex Key,
5/32"
REFER TO FIGURE 1

NEPTUNE II / 3
L10-1003

4 / NEPTUNE II
1. Place the side frames on the deck (or a flat place).
2. Pre-assemble the cross bar, rod rack and D-ring using the screws, and/or washer, and/or
locknut, but don't lock it tight (pre-assemble only).
3. Push down the side-frame keeping the four (4) pads on the same level.
4. Assemble the footrest and tighten securely, keeping the two (2) sides parallel and the four
(4) pads in the same level.
5. Tighten the rod-rack again checking that the four (4) pads are at same level.
6. Tighten the D-ring and make sure it seats properly on the four (4) plastic caps.
7. Assemble the hinge to the seat cushion. Screw the four (4) flat head screws down evenly.
8. Loosen the cross bar and install the hinges as per diagram. Re-install the cross bar and
tighten to the side frame.
9. Check the rod-rack and adjust the angle. There are three (3) angles available with (three) 3
position holes.
10. Check for proper alignment of all components and tighten screws.
11. Install the leaning post to the deck in the appropriate position and secure.
12. Place the softpak storage bag within the D-ring, under the seat cushion. The key ring should
be in the back. Secure in place with the Velcro flaps around the frame.
13. Attach the cooler and eye strap on the rear legs.
14. Assemble the backrest (optional item). When installing optional backrest, use additional
liners provided and glue in place.
ASSEMBLY
INSTALLATION
Clean any dirt or packing debris from accessory splines.
REFER TO FIGURE 1 (P. 3)
WARNING
• It is very important that the leaning post is firmly attached to the deck to prevent injury. Consult your marine
professional for recommendation on proper backing plates and thru-bolting for solid installation.
• Be sure not to drill through wiring, fuel tank or hoses.

NEPTUNE II / 5
RECOMENDED IF ADDED
SECURING IS REQUIRED
1. Before assembling the Leaning Post, check
the footprint dimensions and mark the
approximate locations of the mounting
holes with a wax pencil.
2. Check underneath the deck to make sure
that any gas tanks, gas lines, electrical
wires, etc. are far enough below the deck
so they will not be damaged when drilling
or through bolting the Leaning Post to the
deck.
CAUTION! If you do not know what is
directly underneath your mounting location,
ask your boat manufacturer, a qualified boat
mechanic or use a flashlight to view the area
through an existing access hole or make a
hole in an area that you can properly seal
and cover afterwards.
3. Assemble the Leaning Post according to the
assembly instructions provided.
4. Using the footprint of your Leaning Post,
make backing plates out of a piece of 1/2"
marine lumber or 1/4" aluminum. Make sure
you leave enough material for a cover plate
(Step 14).
5. If the area underneath is acceptable, place
the Leaning Post in the desired location,
about 12" from the console.
6. Make sure that your Leaning Post is straight
and parallel with your console, centered
positioning.
7. Mark the hole locations through the
mounting holes in each mounting flange,
making sure that the Leaning Post does not
move.
8. Install a 3/16" drill bit into your drill and put
a piece of tape on the drill bit 1" from the tip
so you will know when to stop and do not
drill too deep.
9. Drill the mounting holes.
10. Put the Leaning Post back in place to make
sure that all the holes line up. Enlarge holes
if necessary. Use marine sealant on bottom
of mounting plates and fastener holes for a
good seal.
11. If you do not have an access hatch to the
underside of the deck, you will have to cut
an access hole between the two mounting
locations on each side of the leaning post
big enough so you can reach inside and
install a backing plate and locknuts or
T-nuts on the mounting screws. Make sure
that the access hole is completely within the
mounting feet of the leaning post so that
you can seal and cover it up with a piece of
Marine Lumber after the installation.
12. Put sealant on the threads of each of the
1/4" mounting bolts and insert them into the
holes.
13. Install the backing plates and locknuts or
T-nuts on the mounting bolts through the
access holes and tighten them securely.
14. Using a piece of 24" x 54" marine lumber
or 1/8" aluminum, cut the cover plate to
fitwithin the footprint of your Leaning Post.
15. Drill clearance holes in the marine lumber or
aluminum plate for the mounting screws.
16. Using the clearance holes mark the deck
and drill pilot holes so the screws can thread
into the deck.
17. Place sealant around each of the access
holes and line up the holes in the cover
plate with the pilot holes, put sealant on
the screw threads and install the screw to
secure the cover plate to the deck.
18. Install the optional cooler and adjust the
straps.

6 / NEPTUNE II
How to clean
Mild dish washing liquid, specialty marine cleaners:
Sea Safe Boat Wash, Boat Wash Concentrate
and Super Suds.
Safe marine lubricants:
CRC Corrosion Inhibitor, Corrosion Block
and Get Some Extreme.
Bleach (Clorox, etc.) and mild abrasive cleaners:
Ajax, Comet, Soft Scrub, Rubbing Compounds, etc.
Strong cleaners:
409, Engine Degreasers, etc.
Acids of any type:
Such as, Muriatic or aluminum acid
Always use a mild, non-abrasive soap and fresh water. Thoroughly wash the aluminum
and vinyl material with a soft towel or sponge to remove dried salt crystals and other
contaminants. Rinse completely with fresh water.
Safe Cleaners Harmful Cleaners

NEPTUNE II / 7
Need Support?
1.800.653.8568
[e-mail]
tacomarine.com
50 NE 179th ST
Miami, FL. 33162
@tacomarine
@taco_marine
TACO Marine®
Contact Us
We’re here to help.

®
INSTRUCTIONS-NEPTUNE II