Tamlite ZENITH X Series Manual

Product Name:
General information
Dimensions
Page 1 of 3
[phone]
[email protected]
Document No: V1
Tamlite Technical
Stafford Park 12,
Telford, Shropshire,
TF3 3BJ
INSTALLATION & OPERATING INSTRUCTIONS
• This luminaire must be installed in accordance with the latest edition of the IET Wiring Regulations and local Building Regulation
by a qualified competent person.
• The mains power supply must be turned off before inspection, installation or removal of the luminaire, ensuring that the supply is
locked off to prevent inadvertently switching the supply on.
• It is the installer’s responsibility to ensure that the installation is suitable for the total load of the luminaire(s). The supply cable
fuses/circuit breakers must be correctly rated for the electrical load and taking into account for any transient inrush currents that
may occur.
• It is the installer’s responsibility to ensure that the environmental operating and storage conditions are complied with and that any
fire risks are considered.
• Do not perform insulation strength or insulation resistance tests on the installation with the luminaire(s) connected, this can
damage the luminaires and give erroneous readings.
• Do not loop-in supply cables at the luminaire supply terminals unless there is provision for 2-way connection at the terminals.
• The light source contained in this luminaire must only be replaced by Tamlite Lighting or an appointed service agent.
• Emergency lighting luminaires must be installed and maintained in accordance with the emergency lighting standard BS 5266-1.
• To ensure that the product warranty remains valid, the luminaire must be installed and maintained in accordance with these
installation instructions and the product must not be modified in any way.
Luminaires marked with this symbol must not be covered with thermally insulating material.
This symbol on covers over light sources indicates dangerous live parts do not operate the luminaire with this cover removed.
IP65
220-240V
50/60Hz
ta
-40°C to 65°C
0°C to 35°C
for M3 variants
B (mm)A (mm)
701
1312
1611
302XZNT850NW / XZNT850NWM3
XZNT1680NW / XZNT1680NWM3
XZNT2480NW / XZNT2480NWM3
C (mm)
130
130
130
362
362

Page 2 of 3
1
3
5
7
2
4
6
8
Product Name:
[phone]
[email protected]
Document No: V1
Tamlite Technical
Stafford Park 12,
Telford, Shropshire,
TF3 3BJ
INSTALLATION & OPERATING INSTRUCTIONS
IP65
220-240V
50/60Hz
ta
-40°C to 65°C
0°C to 35°C
for M3 variants
Open the diffuser fully and unlock the hinges to remove the diffuser.
For suspended mounting, attach eye bolts to the positions provided.
Position the luminaire in line with the mounting hardware.
For surface mounting, attach the mounting brackets to the rear of the luminaire.
Remove the three screws opposite the hinges to release the diffuser.
Locate the mounting brackets on to the hardware and tighten to secure.
Position appropriate hardware in the mounting surface.
Remove product from its packaging.

Page 3 of 3
9
11
13
15
10
12
14
16
Product Name:
[phone]
[email protected]
Document No: V1
Tamlite Technical
Stafford Park 12,
Telford, Shropshire,
TF3 3BJ
INSTALLATION & OPERATING INSTRUCTIONS
IP65
220-240V
50/60Hz
ta
-40°C to 65°C
0°C to 35°C
for M3 variants
Replace the three screws to secure the diffuser.
Replace the four screws to secure the gear tray.
Terminations shown for standard and emergency variants.
Remove the gear tray from the luminaire body.
Re-locate the diffuser hinges and rotate to close the diffuser.
Replace the gear tray in to the luminaire body.
Bring supply cable through the luminaire body gland and terminate to gear tray.
Remove the four screws which secure the gear tray to the luminaire body.