Tanco 1400 V User manual

TRACTOR CONNECTION
1. Hydraulics
Red pipe > Supply (35-40lpm)
Blue pipe > Return (Free flow return!!)
2. Electrics
A. Connect 12V supply to 3pin plug
B. Connect wrapper harness to controller
C. Connect hand remote to controller
C
A
B
ENTERING THE WORKING POSITION
1. Switch on controller using the red switch
2. Enter the Auto Park Sequence
A. Press the Down arrow to get to the Auto Park Sequence
B. Press Enter
C. Press and hold the Unfold drawbar button until End is
displayed.
3. Install the 2 rolls of film
4. Set the Auto Load paddle into the
working position (if using Auto Load).
The 1400V wrapper will now be in the working position
3
4
The quick reference guide is not a substitute for the Operators Manual!
Please refer to Operators Manual for more detailed information
1400 V QUICK REFERENCE GUIDE

OPERATION
1. Drive into the bale until the Auto load
paddle contacts the bale.
2. The bale will then be loaded,
wrapped, and unloaded
Automatically.
1
1. Drive into the bale.
2. Press the “Load up” button on the
remote (a) or on the controller (b)
to load the bale.
3. The bale will be wrapped and
offloaded Automatically.
Auto mode (A) Auto wrap + Auto offload a
b
1
Auto mode (A) Auto offload
1. Drive into the bale.
2. Press the “Load up” button on the
remote (a) or on the controller (b) to
load the bale.
3. Press “Auto start” on the remote (c)
or controller (d) to begin wrapping.
a
b
c
d
Auto mode (A)
1. Drive into the bale.
2. Press the “Load up” button on the
remote (a) or on the controller (b) to
load the bale.
3. Press “Auto start” on the remote (c) or
controller (d) to begin wrapping.
4. Press “Offload” on the remote (e) or
on the controller (f) to offload the bale.
a
b
c
d
e
f
Auto mode (A) Auto load + Auto wrap + Auto offload

ENTERING THE TRANSPORT POSITION
The 1400V wrapper will now be in the transport position.
1. Remove the 2 rolls of film and place them
on the film roll holders. IMPORTANT!!
2. Enter the “Auto Park Sequence”
A. Press the down arrow to get to “Auto
Park Sequence”
B. Press Enter
C. Press and hold the “Fold Drawbar”
button until “End” is displayed.
HAND REMOTE OPERATION
Manual Mode (M):
Table down
Auto Mode (A): Start
autounloading
Manual Mode (M):
Loadarm out
Auto Mode (A):
Start autowrap
Manual Mode (M):
Table up
Auto Mode (A): Start
autoloading
Manual Mode: Loadarm in
Bale Diameter 4 layres 6 layres 8 layres
120 cm
16 wraps
24 wraps
32 wraps
150 cm
20 wraps
30 wraps
40 wraps
SETTING NO. OF WRAPS
This is a guideline only! Misshapen bales may require more wraps to achieve full coverage.

EXPERT CONTROLLER OPERATION
OPTIONAL RF REMOTE OPERATION
Display in normal working mode:
- Current No. of wraps
- Target No. of wraps
- Wrapping speed
- Bale Total ( 10 seperate
stores )
- Grand Total No. of Bales
- Mode: M ( Manual ) / A ( Auto )
R1 Unfold drawbar position
R2 –Open C&S
R3 –Fast wrap forward / Resume
autowrap (after pause /
emergency stop)
R4 –Add an extra wrap during
wrapping cycle
R5 –Unload bale
R6 –Start Automatic Wrapping
Cycle
L6 – Select Operating Mode: „M“
or „A“
Power On/Off / Emergency Stop
L5 –Load Bale
L4 –Slow reverse arm
L3 –Slow wrap forward
L2 –Close C&S
L1 –Fold drawbar position
4-way Menu switch
- Set no. of wraps
- Change/Reset bale sub-total
- Access Operator setup menu
- Access Technician setup menu
The RF (Radio Frequency) remote is required if you wish to operate the
1400V wrapper statically
Auto Start wrap
Close Cut & Start
Offload the bale
Emergency Stop
Rotate wrap arms in
reverse
Rotate wrap
arms forward
Load bale / add
extra wrap
Open Cut & Start
RF Receiver
The red button on the
rear of the remote must
be pressed while
pressing any other
button (except “STOP”).