Tanco A100 EH User manual

TRACTOR CONNECTION
1. Hydraulics
Red pipe > Supply (25-35lpm)
Blue pipe > Return (Free flow return!!)
2. Electrics
A. Connect 12V supply to 3pin plug
B. Connect wrapper harness to controller
ENTERING THE WORKING POSITION
1. Remove the transport pin from the load arm.
2. Adjust the load arm width to suit the correct
bale size.
3. Adjust the position of the dispenser to
ensure that the film will be applied to the
centre of the bale.
4. Add the film roll into the dispenser, ensuring
that it is threaded correctly, and attach the
film to the Cut & Start.
The quick reference guide is not a substitute for the Operators Manual!
Please refer to Operators Manual for more detailed information
B
A
4
2
1
3
A100 EH QUICK REFERENCE GUIDE

OPERATION
1. Lower the load arm and drive into the
bale until the Auto load paddle
contacts the bale.
2. The bale will then be loaded,
wrapped, and unloaded
Automatically.
1. Drive into the bale.
2. Press and release the “Load arm
up” button on the controller (a) to
load the bale.
3. The bale will be wrapped and
offloaded Automatically.
Auto mode (A) Auto wrap + Auto offload a
Auto mode (A) Auto offload
1. Drive into the bale.
2. Press and release the “Load arm up”
button on the controller (a) to load
the bale.
3. Press “Auto start” on the controller
(b) to begin wrapping. The bale will
then be offloaded Automatically.
a
b
Auto mode (A)
1. Drive into the bale.
2. Press the “Load arm up” button on
the controller (a) to load the bale.
3. Press “Auto start” on the controller
(b) to begin wrapping.
4. Press the “Tip” button on the
controller (c) to offload the bale.
a
b
c
Auto mode (A) Auto load + Auto wrap + Auto offload
1

ENTERING THE TRANSPORT POSITION
1. Rotate the table into the loading
position.
2. Raise the load arm fully.
3. Insert the transport pin into the
load arm. This will prevent the load
arm from lowing when driving on
the road.
The transport pin should also be
used when the machine is being
parked.
Model
Bale Diameter
4 layres
6 layres
8 layres
A100 EH 120 cm
16 wraps
24 wraps
32 wraps
A100 EH 150 cm
20 wraps
30 wraps
40 wraps
SETTING NO. OF WRAPS
This is a guideline only! Misshapen bales may require more wraps to achieve full coverage.
Extra wrap can be applied during wrapping by pressing the “+1”
button.
The “No. of Wraps” will return to the set value for the next bale.

EXPERT CONTROLLER OPERATION
OPTIONAL RF REMOTE OPERATION
The RF (Radio Frequency) remote is required if you wish to operate the
A100EH wrapper statically.
Auto Start wrap
Close Cut & Start
Offload the bale
Emergency Stop
Rotate table in
reverse
Rotate table
forward
Load bale / add
extra wrap
Open Cut & Start
RF Receiver
The red button on the
rear of the remote must
be pressed while
pressing any other
button (except “STOP”).
L1 –Table - tip down (in
Manual mode)
L2 –Cut and Grip Film
L3 –Slow Wrap
L4 –Reverse Table
L5 –Load Arm down
Power On/Off /
Emergency Stop
R1 –Table - tip up in Manual mode
Autotip in Automatic mode
R2 –Release Film Grip
R3 –Fast Wrap / Resume Wrap
(after stopping mid-cycle using the
STOP-switch)
R4 –Add 1 wrap to current (or next)
bale (only in automatic mode)
R5 –Load Arm up
R6 –Start Automatic cycle
Display in normal working mode:
- Current No. of Wraps
- Target No. of Wraps
- Wrapping speed
- Bale Total ( 10 seperate stores )
- Mode: M ( Manual ) / A ( Auto )
L6 – Select Operating Mode: „M“ or „A“
4-way Menu switch:
•Set No. of wraps
•Change/reset bale sub-total
•Access Operator Setup Menu
•Access Technician Setup Menu