Tanco 1814 S User manual

TRACTOR CONNECTION (ARC)
1. Hydraulics
Red pipe > Supply (50 lpm)
Blue pipe > Return (Free flow return!!)
2. Electrics
A. Connect 12V supply to 3pin plug
B. Connect wrapper harness to controller
C. Connect receiver to controller
ENTERING THE WORKING POSITION
1. Lower the rear of the machine to the ground
and adjust the hydraulic jack until the
machine is level.
2. Remove the transport bracket and lower the
unloading conveyor to the ground.
3. Adjust the working width of the rollers to
suit the size of bale being used.
Lock the rocking rollers in
place using the pin.
4. Install the roll of film and attach the film to
the Cut & Start.
The quick reference guide is not a substitute for the Operators Manual!
Please refer to Operators Manual for more detailed information
B
A
4
1
2
3
1814 S / ARC QUICK REFERENCE GUIDE

OPERATION
c
d
b
1. Start the engine to activate the
hydraulic system (S model only).
2. Place a bale on the wrapping
table.
3. With the controller set to “Auto
Mode”, press “Auto Start” on the
remote (a) or on the controller (b).
The wrapping cycle will then
begin.
Once the target number of wraps
is reached, the film will be cut
and wrapping will stop.
4. If “Auto Unload” is activated in
the Operator Settings, the bale
will be automatically unloaded
onto the conveyor once wrapping
is complete.
5. If “Auto Unload” is not selected,
the bale can be unloaded by
pressing “Tip” (c) on the remote
or by pressing “Bale unload” (d)
on the controller.
a

EXPERT CONTROLLER OPERATION
RF REMOTE OPERATION
The RF (Radio Frequency) remote is required if you wish to operate the
1814 wrapper remotely.
Auto Start
wrapping
Close Cut & Start
- Auto Unload (A)
- Unload (M)
Emergency Stop
Rotate wrap arms
in reverse
Rotate wrap
arms forward
- Add additional
wraps (A)
- Rotate bale if not
level (A)
- Tip return (M)
Open Cut & Start
RF Receiver
The red button on the
rear of the remote must
be pressed while
pressing any other
button (except “STOP”).
- Current No. of wraps
- Target No. of wraps
- Wrapping speed (RPM)
- Bale total
- Grand total No. of bales
- Mode: Manual /Auto
Pause wrapping (A)
Rotate rollers (M)
Level bale for unloading (if
not level) (A)
Open cutter
Fast wrap arm rotate
Resume wrapping
Add additional wraps
Unload bale (A)
Tip & Rotate rollers (M)
Start Auto wrap cycle
Select Manual or Auto
4-way Menu switch:
- Set no. Of wraps
- Change/Reset Bale Sub-Total
- Access Operator Setup Menu
- Access Technician Setup Menu
Pause bale rotation (A)
Close cutter
Slow wrap arm rotate
Reverse wrap arm
Not used on S or ARC
Power on/off /
Emergency Stop

ENTERING THE TRANSPORT POSITION
1. Fully raise the unloading conveyor and
lock in place.
2. Raise the machine from the ground
using the Auxiliary Control lever No. 1.
3. Attachment to the tractor can be
assisted by raising or lowering the
drawbar using the Auxiliary Control
lever No.2.
4. Switch off the Engine.
AUXILIARY CONTROL VALVES
1. Used for lowering the machine
to the ground in preparation for
wrapping.
2. Used for adjusting hydraulic jack
at drawbar. This is necessary for
levelling the machine prior to
wrapping.
3. Used for adjusting the width of
the rocking rollers when
changing to different size bales.
4. Used for raising and lowering
the unloading conveyor.
1 2 34