Tanita WB-380 User manual

Eng
Please read this Instruction Manual carefully and keep it
handy for future reference.
Temperature Range for Use : 41˚F 95˚F / 5°C 35°C
Relative Humidity : 30% 80% (without condensation)
Temperature Range of Environment : 14˚F 122˚F / -10°C 50°C
Range of Relative Humidity : 10% 90% (without condensation)
To avoid malfunctions, avoid storing the equipment where there is direct sunlight, significant temperature
changes, the risk of dampness, a large amount of dust, in the vicinity of fires, or where there is the risk
of receiving vibrations or shocks.
<Storage Conditions>
<Usage Conditions>
ELECTRONIC SCALE
WB-380
Instruction manual

2. Safety Notes
1. Table of Contents
Eng
2
Warning Ignoring instructions highlighted with this mark could result in death or severe
injury.
Caution Ignoring instructions highlighted with this mark could result in injury or damage to
ro erty.
This mark indicates actions that are rohibited.
This mark indicates instructions that must always be adhered to.
Warning
The following outlines p ecautiona y measu es to be taken to avoid inju y to the use s of this device and
othe s, and to p event damage to p ope ty. Please familia ize you self with the contents to ensu e the safe
ope ation of this equipment.
2. Safety Notes ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••2
3. Part Names •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••6
4. Assembly Instructions •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••8
5. Functions•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••10
6. Set up••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••10
7. Power supply ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••11
8. Operation••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••12
9. Based on NI /W O BMI Guidelines••••••••••••••••••••••••••••••••••13
10.Measuring height procedure ••••••••••••••••••••••••••••••••••••••••••••••••••••14
11.Output data format•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••16
12.Troubleshooting•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••18
13.Specifications•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••19
Prohibited
Do not handle the lug with a wet hand.
Such action may result in electric shock, fire, or leakage.
Kee this equi ment away from flammable gas and oxygen rich environment.
No modification of this equi ment is allowed.
There is a risk of electrocution or injury. Nor can precise analysis be guaranteed.
Do not use double ada ters.
May result in fire.
Always…
Use only a correctly wired outlet.
Only genuine cables and equipments are allowed.

Eng
3
Caution
Stand clear of the subject during measurement to ensure accuracy.
Always…
Kee away from water.
Do not jum on the equi ment.
Do not insert fingers into ga s and holes.
Do not a ly force to the dis lay.
The screen panel may break and cause injury.
Assist ersons with disabilities.
Another person should assist persons with disabilities who may not be able to take a measurement alone.
Be sure clean the scale latform with a ro riate disinfectant after each use.
Continually monitor both the subject and the equi ment for anomalies.
If an anomaly in the subject or equipment is discovered,take appropriate action, such as stopping the
equipment, while ensuring the safety of the subject.
Be sure to use the included AC ada ter.
Un lug the AC cable from the equi ment when moving it.
When not in use for a long time, un lug the AC Ada ter from the wall socket.
Inter retation of analysis results (e.g. evaluation of measurements and formulation of exercise
rogrames based on results) must be erformed by a rofessional.
Weight loss measures and exercise based on self-analysis could be harmful to you health. Always follow
the advice of a qualified professional.
Prohibited

Eng
4
For Accurate Measurements
Always…
Ensure the weighing latform is laced on a level and stable surface.
Avoid measuring in multi le locations with greatly differing tem eratures.
This may cause inaccurate measurements. Allow the equipment to stand for at least
2 hours before using if it is moved to a new location with a temperature difference
of 36˚F / 20°C or more.
Avoid subjecting the equi ment to excessive shocks or vibrations.
Use in a stable location.
Errors in measurements may occur if the device is used in an unstable location.
Scheduled Maintenance
Always…
U date settings, re lace items, or call for service as necessary according to the results of the
visual ins ections. Do not use the unit if you see any signs of damage. Equi ment that has been
damaged must be checked for ro er o eration by qualified ersonnel before using again.
TANITA recommends that each facility conduct eriodic checks of each unit.
1. Check the following at least daily:
• The unit is on a stable and level surface ie on a firm flooring, not on a thick carpet
2. Visually inspect the following at least weekly:
• The display for any damage or contamination
• All cables, cords, and connector ends for damage or contamination
• All safety-related labeling for legibility
• All accessories (sensors, electrodes, etc.) for wear or damage
3. Visually inspect the following at least monthly:
• Screws on equipment

Eng
5

Eng
6
Display Box
Release Screw Knob
Height Rod Arm
Platform
WB-380H
WB-380S
WB-380P
Platform
Display Box
Display Box
Accessories
AC Adapter
Screw x 4
CD ROM
(This Manual)
AC Adapter
CD ROM (This Manual)
Back Cover Front Cover
<WB-380H, WB-380P><WB-380S>
Battery Box
DC JackLid
3. Part Names

Eng
7
쎱Symbols and their Meanings
쎱Control Panel
Display Unit On
Caution
Refer to the attached notes.
Zero reset
Changing Measurement
Units
Select BMI mode
Adjust height for BMI
Output
Direct current
Display Unit Off

Eng
8
4. Assembly Instructions
Platform (fully assembled and pre-wired to display assembly)
Cable (Platform side)
Lower Pole Assembly
Screw
Cable (Cables) (Top Head Display Assembly Side)
Top Head Display Assembly (fully assembled and pre-wired to platform)
Back Cover
Front Cover
Top Height Rod Assembly (fully assembled with pivoting height measuring lever)
Height Rod Arm
Lower Height Rod Assembly

Eng
9
For WB-380H For WB-380P
Install the lower pole into the
plateform using the four (4)
screws.
Install the lower pole into the
plateform using the four (4)
screws.
Push all the way down assem-
bled the top height rod to the
lower height lod opening on
the pole.
Assemble the top head display
into the lower pole inserting the
cable into lower pole.
Connect the cable inside the bot-
tom of the lower pole.
Connect the cables inside the
bottom of the lower pole.
Attach the back cover and the front cover as shown. Attach the back cover and the front cover as shown.

Eng
10
5. Functions
쎱Automatic Power Off
This equipment has an automatic power off function that automatically turns off the power in order to reduce
battery consumption.
If the display does not change for 30 seconds, the power will be automatically turned off.
6. Set up
쎱Flat and stable location
쎱Angle Adjustment
1) Fully release screw knob on the pole. 2) The display box could select at 90-degree 2 positions be sure to
screw it tightly after setting the position.
To obtain the highest level of accuracy, please make sure that all four (4) feet are touching on the floor
evenly.
For further accuracy and security, please position the two (2) adjustable supporting feet on the platform
(found under the front cover) until they just make contact with the floor (do not overextend)
•Do not position it anywhere that is subject to direct sunlight, near heating equipment, or directly in the
path of an air conditioner outlet.
•Do not use it anywhere that is subject significant temperature change.
•Do not position it anywhere that it either damp or subject to high humidity.
CAUTION • Put the weighing platform on a flat, level surface.

Eng
11
7. Power supply
쎱AC adapter
AC adapter is much preferable when the scale will be used continuously.
1) Plug on the AC adapter. Insert
the AC adapter jack into the
DC Jack on the back of the
pole.
2) Insert the connecter into the
DC Jack on the back of the
display box.
Plug on the AC adapter. Insert the AC adapter jack into the DC
Jack on the back of the display box.
1) Pull up the battery case which located on top of display.
2) Ensure that the batteries are inserted with the correctpolarity.
3) push down the battery case completely.
4) Unplug the DC connecter on the back of the display box.
* Insert new batteries such that the negative terminals of the batteries are pushed up against the
coils within the battery housing.
Unplug the DC connecter.Or the scale wouldn’t work.
<Back side>
For WB-380H, WB-380P
For WB-380H, WB-380P For WB-380S
For WB-380S
쎱Batteries
Caution

Eng
12
(or )
d
d
d
d
d
2. BMI Weighing
1) Turn on the power by pressing the key.
2) After all the segments flash, [0.0lb / 0.0kg] is displayed.
3) The person to be weighed should still in the middle of the platform.
4) The weight will be locked-in and displayed on the display. “ (Hold)” sign will appear in the upper
left corner of the display.
5) Press the key (or ). The default height [5ft7.0in / 170cm] will be displayed.
6) Set the height with the key.
7) Once the height and weight have been established, press the key.
The weight and BMI calculation will then be displayed.
When the scale is connecting to an external device, weight, height and BMI data will be exported
at this time.
8) The scale will automatically shut off in 30 seconds.
The setting of height for BMI is can be accomplished in any one of the following means by press-
ing the key (or ).
•Before stepping on the scale.
d
d
d
d
d
d
8. Operation
1. Standard Weighing Procedures
1) Turn on the power by pressing the key.
2) After all the segments flash, [0.0lb / 0.0kg] is displayed.
3) The person to be weighed should still in the middle of the platform.
4) The weight will be locked-in and displayed on the display. “ (Hold)” sign will appear in the upper
left corner of the display.
When the scale is connected to an external device, weight data will be exported at this time.
5) The scale will automatically shut off in 30 seconds.
Note: •Do not press the key while standing on the scale, as accurate measurement will not be
possible.

Eng
13
9. Based on NIH/WHO BMI Guidelines
Under Weight
Normal Range
Pre obese
Obese
Obese
Obese
CLASS l
CLASS ll
CLASS lll
BMI ⬍18.5
18.5 ⬉BMI ⬍25
25 ⬉BMI ⬍30
30 ⬉BMI ⬍35
35 ⬉BMI ⬍40
BMI ⭌40
d
d
4. Changing Measurement Units
This function is used to change the measurement units on the display.
e.g. When change the unit “kg” to “lb”.
Press the key.
The measure shifts from “kg” to “lb” and the measurement units change.
5. Power off
Press the key and key at the same time to turn off.
3. Step on Function
The scale will turn on automatically when the user steps onto the platform.
Note:
•If the weight is less than 22lb / 10kg, the “Step-On” function will not work.
•If person less than 22lb / 10kg, press the key manually to turn on the scale.
•If an item is placed on the scale while it is powered off, accurate measurement will not be possible and the Step on Function may not operate
properly.
•After pressing the key.
•After weight measurement while the weight result remains on the display.

Eng
14
10. Measuring height procedure
The user should step on the platform without wearing shoes for accurate
measurement.
Always have someone assist the user for accurate measurement.
1) Adjust the Height Rod Arm position before the user steps on the platform. Place
hand on the Height Rod Arm.
If the subject is taller than 48"/ 120 cm, pull the eight Rod Sliding Block and
eight Rod Arm at the same time upward so that the arm is positioned higher
than the subject’s head.
If the subject is shorter than 48"/ 120 cm, move the eight Rod Arm down.
Incorrect way to hold
the Height Rod Arm
Correct way to hold
the Height Rod Arm
To avoid danger of breaking or coming loose, you
must hold the height rod arm securely.
2) Gently lower the Height Rod Arm until the Height Rod Arm touches the very top of the
user’s head.
3) Read the measurement.
If the subject is taller than 48"/ 120
cm, read the number just above the
top of the Upper Pole Column (see
example #1).
If the subject is shorter than 48"/
120cm, read the number below the
eight Rod Arm (see example #2).


48" / 
READ HERE


48" / 


48" / 


48" / 
For WB-380H
Example #1:
58" (147.5 cm) Example #2:
36.25" (92 cm)

Eng
15

Eng
16
11. Output data format
This section covers the exporting of data from the scale to an external device (e.g. PC) using a RS-232C and USB compliant signal.
•RS-232C and USB interface are for data OUTPUT ONLY!
•This scale is not capable of receiving instructions from an external device.
Note:
•An RS-232C connector (D sub 9-pin female) and USB connector (B-type 4-pin female) are located on the back of the display unit.
•Please provide your own cables as necessary as none are included.
RS-232C :Straight D sub 9-pin (male) – D sub 9-pin (female)
USB :A-type 4-pin (male) – B-type 4-pin (male)
•Select Switch : Please select which interface you would like to use
If you want to use the USB output, you must install the necessary driver on to your PC, available to download
from http://www.tanita.com
Specifications
Signal Line Name and Connection Method
Communications standard
Terminal no. Signal name
TXD
GND
1
2
3
4
5
6
7
8
9
Communications method
Signal speed
Data bit length
Parity
Stop bit
Terminator
EIA RS-232C compatible USB
Asynchronous transaction
9600 baud
8 bits
None
1 bit
CR+LF
RS-232C Port USB Port
RS-232C/USB Select SW
5
96
1

f
Wp
Eng
17
eight m xxx.x x.xx.x
xxx.x
xx
{0
˜0
˜1
Output data
Name of item Header
Weight
BMI
Checksum
Output data (ASCII code) Pattern
BMI mode
4 – 6 bytes
3 – 5 bytes
Control data
Control data
Control data
Model
Control data
Fix to 16
Fix to 1
Fix to 1
Fix to 1
2 Bytes fixed
1 Byte fixed
1 Byte fixed
1 Byte fixed
MO"WB-380" 8 Byte fixed
2 Bytes fixed
˜2
Wk
CS
xxx.x 3 – 5 bytes
MI
Note:
•The data are divided with commas (,) for each data.
•The terminator (end of the data) is CR (ASCII code 0D ), LF (ASCII code 0A ).
•The control data for the items 1 – 4 are for expansion. They are not used presently so the receiving side can ignore them.
•Because of its specifications, the scale will output an irrelevant signal approximately 0.1 second after data output. Make sure you ignore this
signal and do not import it.
[Output example]
Weight mode
kg mode lb mode

Eng
18
12. Troubleshooting
If you are concerned that the scale may not be functioning correctly, please check the following point before requesting repairs.
Problem Check Points
Nothing is displayed when key is
pressed.
“Lo” is displayed.
Measurement is not accurate.
The weight does not stabilize
“OL” is displayed
“-OL” is displayed
“Error” is displayed
•Check the connection of the AC adapter jack to the DC jack, and the connection of the AC
adapter plug to the power outlet.
•The batteries may be weak. Try an AC adapter or new LR6 (AA) batteries.
•Check the terminals of the batteries for contamination
•Batteries Unplug the DC connecter on the back of the display box.
The batteries are running out. Please replace them immediately or use the AC adapter.
•Check that all feet of scale are stable and on a hard flat surface, carpeting depth should be
kept to a minimum.
•After having stepped down from the scale and pressed the key, perform the
measurement again.
•Accurate measurement may be impossible if the product is used where there is excessive
vibration.
•Are you moving during measurement?
•Is the measured weight within the range of weight measurement?
•Are you touching the height rod arm, switch, or another part during measurement?
•The range of weight (660lb / 300kg) is exceeded.
•Was anything placed on the scale before measurement?
•Check whether the cable between the platform and display is disconnected, cut, or pinched.

41°F - 95°F
DC 6V 500mA (LR6 - AA Alkaline Battery x 4)
5°C - 35°C
Tem erature Range of usage
Rated Power
Eng
19
13. Specifications
Model WB-380
Strain Gauge Load Cell
660lb / 0.2lb
0 - 660lb 0 - 300kg
22 - 660lb 10 - 300kg
Mechanical eight Rod
2ft 1in – 7ft
2ft – 8ft 2in 0.5in increment
660lb / 0.2lb
2ft – 8ft 2in 0.5in increment
0.1 increments
W15.6 X D21.7 X 56.1 in
Total 24.7lb
W15.6 X D23.4 X 47.1 in
Total 22.1lb
W15.6 X D20.8 X 4.8 in
Total 15.7lb
W15.0 x D15.0 x 2.0 in
Upper 5Digits and Lower 4Digits LCD
eight of numerals 1in / 24mm
RS-232C (D sub 9-pin Female connector) USB (B-type)
AC adapter (included) Center Minus
0.3 W max.
W395 x D552 x 1425 mm
Total 11.2kg
W395 x D595 x 1196 mm
Total 10.0kg
W395 x D529 x 123 mm
Total 7.1kg
W380 x D380 x 51 mm
61cm- 250cm 1cm increments
300kg / 0.1kg
61cm- 250cm 1cm increments
64cm – 214cm
300kg / 0.1kg
Weight Measurement
Measurement System
Maximum Ca acity / Minimum Graduation
Height Measurement
Range of Weight Standard
Ste on
Measurement System
Range of Height
In ut Items Height
Out ut Items Dis lay
Weight
Height
BMI
WB-380H
WB-380P
WB-380S
Size Overall
Platform
Dis lay
Out ut Data Interface
Power Source
Power Consum tion

© 2015 TANITA Corporation.
Eng
WB3807621(0)-1501CF
This device features radio interference suppression in compliance with EC
Regulation 2004/108/EC
Disposal
This equipment is electronic device. Please
dispose of this equipment appropriately as
not the genera l household waste but elec-
tronic equipment. Please follow a regional
regulation when you dispose of this.
www.tanita.asia
www.tanita.com.cn
Room 8005, 877 Huai Hai Zhong Lu, Shanghai,
The People's Republic of China
TEL: [phone]
FAX: [phone]
(Shanghai)Trading Co., Ltd.
www.tanita.co.in
174-8630
USA and Canada
Federal Communications Commission and Canadian ICES Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules
and Canadian ICES-003. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. owever, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow-
ing measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for help.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by
Tanita Corporation may void the user’s authority to operate the equipment.