Taymor Madera User manual

✁
1
HINGES HINGES
A.
LEFT
HANDING
B.
RIGHT
HANDING
INSTALLATION INSTRUCTIONS
MADERA
TOOLS AND MATERIALS REQUIRED
> Drill
> 2-1/8” (54 mm) Hole Saw > Chisel
> 3/8” (10 mm) Drill Bit > Phillips Screw Driver
> 1” (25 mm) Wood Bit > Tape Measure
DETERMINE DOOR HANDING
Stand at the exterior side and face the door.
A. Your door is a LEFT HAND door if hinges
are installed at your left hand.
B. Your door is a RIGHT HAND door if hinges
are installed at your right hand.
2a USE THROUGHBOLT TEMPLATE TO MARK
AND DRILL HOLES
2. DRILL HOLES
Select backset. Mark and drill
holes as shown.
1”
(25 mm)
3/8”
(10 mm)
2-1/8”
(54 mm)
2b IF REPLACING EXISTING HANDLESET OR INSTALLING ON PRE-DRILLED
DOOR, CHECK DOOR JAMB AND DOOR PREPARATION
2-1/8”
(54 mm)
5”
(127mm)
2-1/8”
(54 mm)
3/8”
(10 mm)
1” (25 mm)
1” (25 mm) or 7/8” (22 mm)
OR
OR
8-5/8” (219 mm)
Chisel outlines for strike plates until they sit
flush with door edge.
1-1/2” (38 mm) High
1” (25 mm) Wide
1-3/16” (30 mm ) Deep
1” (25 mm) Radius
5/16” (8 mm) Deep
1. MARK DOOR
Use template attached to mark
holes on door face.
A. Make mark for 1”(25 mm) hole
on door edge.
B. Height 36” (914 mm) to 38”
(965 mm) from floor.
Backset
2-3/8” (60 mm)
or
2-3/4” (70 mm)
3CHOOSE LATCH FACE PLATE FOR HANDLESET & DEADBOLT
Chisel 1/8” (3 mm) deep or until
latch face plate is flush with door
edge.
RADIUS OR SQUARE CORNER
MORTISE DRIVE-IN
1
2
3
Ø
3/8” (10 mm)
8-5/8” (219 mm)
CENTER TO CENTER
FEB. 2014
1-3/4”
(45 mm)
1-3/8”
(35 mm)
1-9/16”
(40 mm)
1-3/4”
(45 mm)
1-3/8”
(35 mm)
1-9/16”
(40 mm)
Mark Height 36" (914 mm) from Floor to Center
2-3/4” (70 mm) 2-3/8” (60 mm)
Backset
Fold here. Place on door edge.
CARE AND MAINTENANCE
The following care instructions should be followed to ensure a long lasting finish:
1. Remove locks, or do not install locks, prior to painting your door.
2. Periodically clean with mild soap and a soft cloth only.
3. Do not use abrasives or harsh chemicals
Drill 1” (25 mm) hole at center of door edge.
Drill 1” (25 mm) hole at center of door edge.
5” (127 mm)
Ø 2-1/8 “ (54 mm)
Ø 2-1/8 “ (54 mm)
CENTER TO CENTER
Backset
IMPORTANT! TEMPLATE MUST PRINT AT 1/1 SCALE
Sheet size: 11” x 17”
(280mm x 432mm)

6INSTALL HANDLESET, INSIDE LEVER OR KNOB
Install Handleset Install Inside Knob or Lever
4IF NECESSARY ADJUST LATCH INSTALLATIONS FOR PROPER BACKSET
BACKSET
2-3/8” (60 mm)
or
2-3/4” (70 mm)
For 2-3/4”
(70 mm)
123
HANDLESET
Insert Handleset Spindle for
2-3/4” Backset
2-3/8” Backset
SPINDLE
rednilyC edistuO .1
hctaL tlobdaeD .2
nrutbmuhT .3
4. 2-5/8” (66 mm) Deadbolt Screws (2)
etalpecaF renroC dednuoR .5
6. 3/4” (19 mm) Latch Screws (4)
)4( swercS ekirtS )mm 23( ”4/1-1 .7
8. Handleset
9. Handleset Latch
10. Inside Knob or Lever
OR
16
15
17
18
OR
EXTERIOR INTERIOR
12
34
5
6
7
8
11
13 12
13
16
6
7
7
5
10
19
20
7
DEADBOLT
11. 1-1/2” (38 mm) Dome Head Knob Screws (2)
12. 1-1/4” (32 mm) Handleset Post Screw (1)
Washer .31
Screw Cap .41
Deadbolt Strike .51
16. Latch Strike
17. 3” (76 mm) Reinforcement Screws (2)
18. Reinforcment Strike Plate
19. 2-Piece Drive-In Collar for Deadbolt Latch
20. 2-Piece Drive-In Collar for Handleset Latch
8INSTALL STRIKES
Install strikes onto door jamb.
OR
High Security Double Strike
3” (76 mm) Screws
Reinforcement Plate
7(FOR SINGLE CYLINDER FUNCTION) INSTALL OUTSIDE CYLINDER
HOUSING AND INTERIOR THUMBTURN
Install Outside Cylinder Install Thumbturn
a
b
taymor.com
Deadbolt spindle in
horizonal position
14
9
5INSTALL HANDLESET LATCH AND DEADBOLT
SLEEVE
Tap latch flush
• Place sleeve over handleset latch before installation in square
corner or radius corner mortise configuration
• Do not use sleeve for installations in drive-in configuration
IMPORTANT! TEMPLATE MUST PRINT AT 1/1 SCALE
Sheet size: 11” x 17”
280mm x 432mm