ABH 6500 Series User manual

DETAIL B
R
Owww.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224) c 2012 ABH Mfg., Inc.
printed in USA
INSTALLATION INSTRUCTIONS
1. Prep door according to latch backset per template.
2. Install latch (Item 1) using either wood or machine screws (Items 2 or 3) depending on door type.
3. Take both base assemblies (Items 4 & 6) androtatecam pin as shown in Detail “A” above. Place
pull base over-ride assembly (Item 4) on pull side of door and slide the cam shaft through the latch
cam. Place push base locking assembly (Item 6) on push side of door and engage push cam onto
the pull side cam shaft. Both privacy cam pins must be at the 12 o’clock position in order for
the privacycam shafts to interlock as shown in Detail “B”. Check that they are interlocked
properly by rotating one privacy cam and making sure the other side is rotatingat the same time.
4. Fasten both side using (4) ¼-20 machine screws and lock nuts (Items 5 & 7). Test both handles for
free movementof the latch bolt before tightening all screws. If latch bolt does not extend or retract
freely because of any type of binding, loosen screws to align adjustment of base assemblies and
retighten screws one at a time while checking for proper latch retraction. Mounting hardware (Items
5 & 7) must be tightened before proceeding to next step.
5. Place over-ride cover assembly (Item 8) on the pull side of the door making sure that theforks on
the inside of the cover engages the privacy cam and fasten with (2) 8-32 screws (Item 2).
6. Repeat Step 5 with locking cover (Item 9) on the push side of the door.
PARTS LIST
DESCRIPTIONQTYITEM
LATCH
11
8-32 X 3/8" FHMS U/C
62
#8 X 3/4" FHWS23
PULL BASE OVER-RIDE ASSY
14
1/4-20 X 2-1/2" PH. TRUSS HD. M.S.
45
PUSH BASE LOCKING ASSY16
1/4-20 LOCKNUT47
COVER ASSEMBLY (OVER-RIDE)
1
8
COVER ASSEMBLY (LOCKING)
19
6500 PRIVACY LATCH-PUSH SIDE THUMBTURN LOCK
6500-1-07.IDW
6500
REVISED 08-08-12
1
2
2
2
2
9
2
5
4
5
3
7
7
6
NOTE:
BEFORE MOUNTING BASE
ASSEMBLIES, CAMS MUST
BE POSITIONED PER DRAWING
SHOWN IN DETAIL 'A'
DETAIL 'A'
LATCH CAM
CAM SHAFT
8
FORK
OVER-RIDE COVER
LOCKING THUMBTURN
PRIVACY PULL
CAM SHAFT
2
3
PRIVACY
CAM SHAFTS
PRIVACY PUSH
CAM SHAFT
PRIVACY
CAM PINS

1-1/8 9/16
5/32
13/16
1-5/8 1-1/8 2-1/4
C
LOF DOOR
DRILL 1-1/8" D. TO INTERSECT 2-1/8" D HOLE
(2) #8 F.H.W.S. OR 8-32 F.H.M.S.
L
C
L
C
SEE TEMPLATE
FOR BACKSET 2-1/8" D. DR. THRU
(4) 5/16" DIA THRU
TEMPLATE
VERIFY
1/2 DOOR
EDGE OF STOP
(OR SILENCER)
C
LOF
1/32
9/16
2-1/8
1
2-1/82-3/4
9/16
1-1/8
1-5/16
5/64
3/8
1/4
1/4 3/8
3/32
3-1/4
4-3/4 4-1/8
1"
4-1/8 4-7/8
3-3/8 1-1/2
15/16 1/32 (2) TAP
(2) DRILL FOR
#8 SCREW
1-1/4
1-1/4
2-1/2
LATCH
1-7/16
DOOR PREP
1. Install door
2. Locate horizontal centerline on door
3. Verify backset (2-3/4", 3-3/4", 5"or 7"). Tape template to door.
FRAME PREP
1. Mark centerline of latch bolt on frame
2. Center strike and mark screw positions
3. Mortise to required strike and box depth
ASA STRIKE & BOX STANDARD STRIKE & BOX
LATCH/HANDLEASSEMBLY
1. Install latch bolt.
Radius portion of latch bolt must
face push side of door.
2. Install pull side handle assembly down * with latch
shaft thru latch bolt assembly.
3. Mount push side handle down * and install
(4) 1/4-20x2-1/2" screws with nuts.
4. Mount Cover.
BACKSET
#12-24
THICKNESS
ALLDIMENSIONSININCHES
*CAM PIN MUSTBE ROTATEDTOWARDSIDEINDICATEDBY ARROW
STAMPEDON BASESEEDRAWINGON FRONTOF TEMPLATE PUSHSIDE
c 2009 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R
6500
REVISED08-08-12
6500-2-07.DWG
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT

6500 SERIES PRIVACYHOSPITAL
REVISED08-08-12
R
Owww.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224) c 2012 ABH Mfg., Inc.
printed in USA
VERTICAL MOUNT
6500-3-07.DWG
6500
PUSH/PULLLATCH DOOR PREP INFORMATIONFOR
DOORPREPINFORMATION:
1. BACKSETDIMENSIONFROMLOW EDGEOF BEVEL.
2. CENTERPUNCHALL HOLES.
3. DRILLHOLES(FORHOLLOWMETALDOORS,DO NOT DRILL
THRU.CENTERPUNCH& DRILLHOLESFROMBOTH SIDESOF DOOR).
7/8
1-3/4
1-11/16
3-3/8
Ø5/16
Ø2-1/8
THRU
THRU (4)
BACKSET
LOCK EDGE OF DOOR
VERTICALMOUNTING
ADA RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
FINISHED FLOOR
DO NOT COPY AND USE THIS AS A TEMPLATE
PLEASE CALL FACTORY FOR FULL SCALE TEMPLATE