TDK-Lambda GENESYS GEN 2400W Series User manual

83-517-000 Rev.A
TECHNICAL MANUAL FOR
1U GENESYS™ 2.4kW
PROGRAMMABLE DC POWER SUPPLIES
Document: 83-517-000 Rev. A
TDK-Lambda Americas Inc.
405 ESSEX ROAD, NEPTUNE, NJ 07753
TEL: [phone]
FAX: [phone]
WEB: www.us.tdk-lambda.com/hp

83-517-000 Rev.A
THIS PAGE
INTENTIONALLY
LEFT BLANK

83-517-000 Rev.A
GENESYSTM Manual Supplement
FOR UNITS EQUIPPED WITH “LAN” OPTION,
REFER TO USER’S MANUAL P/N 83-034-100.
FOR UNITS EQUIPPED WITH “IEMD” OPTION,
REFER TO USER’S MANUAL P/N 83-030-200.
FOR UNITS EQUIPPED WITH “USB” OPTION,
REFER TO USER’S MANUAL P/N 83-033-800.

83-517-000 Rev.A
THIS PAGE
INTENTIONALLY
LEFT BLANK

83-517-000 Rev.A
TABLE OF CONTENTS
WARRANTY .................................................................................................................................................1
SAFETY INSTRUCTIONS............................................................................................................................2
FRENCH .......................................................................................................................................................5
GERMAN ......................................................................................................................................................7
ITALIAN........................................................................................................................................................9
PORTUGUESE...........................................................................................................................................11
SPANISH ....................................................................................................................................................13
CHAPTER 1 GENERAL INFORMATION...................................................................................................15
1.1 USER MANUAL CONTENT ..................................................................................................................15
1.2 INTRODUCTION...................................................................................................................................15
General Description......................................................................................................................151.2.1 Models Covered by this Manual ...................................................................................................151.2.2 Features and Options ...................................................................................................................151.2.3 Multiple Output Power System .....................................................................................................161.2.4 Control Via the Serial Communication Port..................................................................................161.2.5 Analog Voltage Programming and Monitoring..............................................................................161.2.6 Parallel operation..........................................................................................................................161.2.7 Output Connections......................................................................................................................161.2.8Cooling and Mechanical Construction..........................................................................................161.2.9
1.3 ACCESSORIES ....................................................................................................................................17
Included Accessories....................................................................................................................171.3.1 Optional Communication Cables (See Section 7.5) .....................................................................171.3.2 AC Cables.....................................................................................................................................171.3.3
CHAPTER 2 SPECIFICATIONS ................................................................................................................18
2.1 OUTPUT RATING.................................................................................................................................18
2.2 AUXILIARY OUTPUTS..........................................................................................................................18
2.3 INPUT CHARACTERISTICS.................................................................................................................18
2.4 CONSTANT-VOLTAGE MODE.............................................................................................................18
2.5 CONSTANT-CURRENT MODE............................................................................................................18
2.6 ANALOG PROGRAMMING AND MONITORING..................................................................................18
2.7 PROGRAMMING AND READBACK (RS-232/485, OPTIONAL LAN, IEEE, USB INTERFACE).................18
2.8 PROTECTIVE FUNCTIONS .................................................................................................................19
2.9 FRONT PANEL .....................................................................................................................................19
2.10 ENVIRONMENTAL CONDITIONS......................................................................................................19
2.11 MECHANICAL CONSTRUCTION.......................................................................................................19
2.12 EMC.....................................................................................................................................................19
2.13 SAFETY ..............................................................................................................................................19
2.14 SUPPLEMENTAL CHARACTERISTICS.............................................................................................20
2.15 GENESYSTM 2400W POWER SUPPLY OUTLINE DRAWING.........................................................21
CHAPTER 3 INSTALLATION ....................................................................................................................22
3.1 GENERAL .............................................................................................................................................22
3.2 PREPARATION FOR USE....................................................................................................................22
3.3 INITIAL INSPECTION ...........................................................................................................................22
3.4 RACK MOUNTING................................................................................................................................22
To Install the Power Supply in a Rack:.........................................................................................223.4.1 Rack-Mount Slides (optional):.......................................................................................................233.4.2
3.5 LOCATION, MOUNTING AND COOLING.............................................................................................23
3.6 AC SOURCE REQUIREMENTS ...........................................................................................................23
3.7 AC INPUT POWER CONNECTION ......................................................................................................23
AC Input Connector ......................................................................................................................243.7.1 AC Input Cord ...............................................................................................................................243.7.2

83-517-000 Rev.A
AC Input Wire Connection ............................................................................................................243.7.3
3.8 TURN-ON CHECKOUT PROCEDURE.................................................................................................25
General .........................................................................................................................................25
3.8.1 Prior to Operation..........................................................................................................................253.8.2 Constant-Voltage Check...............................................................................................................263.8.3Constant-Current Check...............................................................................................................263.8.4 OVP Check...................................................................................................................................263.8.5 UVL Check....................................................................................................................................263.8.6 Foldback Check............................................................................................................................273.8.7 Address Setting.............................................................................................................................273.8.8 Baud Rate Setting (RS-232 and RS-485 only).............................................................................273.8.9
3.9 CONNECTING THE LOAD ...................................................................................................................27
Load Wiring...................................................................................................................................273.9.1 Current Carrying Capacity ............................................................................................................273.9.2 Wire Termination...........................................................................................................................283.9.3 Noise and Impedance Effects.......................................................................................................283.9.4 Inductive Loads.............................................................................................................................293.9.5 Making the Load Connections ......................................................................................................29
3.9.6 Connecting Single Loads, Local Sensing (default configuration).................................................323.9.7 Connecting Single Loads, Remote Sensing.................................................................................323.9.8 Connecting Multiple Loads, Radial Distribution Method...............................................................323.9.9 Multiple Load Connection with Distribution Terminals................................................................333.9.10 Grounding Outputs......................................................................................................................333.9.11
3.10 LOCAL AND REMOTE SENSING.......................................................................................................34
Sense Wiring...............................................................................................................................343.10.1 Local Sensing .............................................................................................................................343.10.2 Remote Sensing .........................................................................................................................353.10.3 J2 Sense Connector Technical Information................................................................................353.10.4
3.11 REPACKAGING FOR SHIPMENT......................................................................................................35
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS........................................36
4.1 INTRODUCTION...................................................................................................................................36
4.2 FRONT PANEL CONTROLS AND INDICATORS.................................................................................36
4.3 REAR PANEL........................................................................................................................................38
Auxiliary Power Supply.................................................................................................................394.3.1
4.4 REAR PANEL SW1 SETUP SWITCH...................................................................................................39
SW1 DIP-Switch Position Function...............................................................................................404.4.1 Resetting the SW1 DIP-switch......................................................................................................404.4.2
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR .............................................41
Making J1 connections .................................................................................................................414.5.1
CHAPTER 5 LOCAL OPERATION............................................................................................................43
5.1 INTRODUCTION...................................................................................................................................43
5.2 STANDARD OPERATION.....................................................................................................................43
Constant-Voltage Mode................................................................................................................435.2.1 Constant-Current Mode ................................................................................................................435.2.2 Automatic Crossover.....................................................................................................................445.2.3
5.3 OVER-VOLTAGE PROTECTION (OVP)...............................................................................................44
Setting the OVP level....................................................................................................................445.3.1 Activated OVP protection indications............................................................................................445.3.2 Resetting the OVP circuit..............................................................................................................445.3.3
5.4 UNDER VOLTAGE LIMIT (UVL) ...........................................................................................................44
Setting the Output UVL level ........................................................................................................445.4.1
5.5 FOLDBACK PROTECTION...................................................................................................................45
Setting the FOLDback Protection.................................................................................................455.5.1 Resetting Activated Foldback Protection......................................................................................455.5.2
5.6 OUTPUT ON/OFF CONTROL...............................................................................................................45
5.7 OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR.......................................45
5.8 ENABLE/DISABLE CONTROL VIA REAR PANEL J1 CONNECTOR ..................................................46

83-517-000 Rev.A
5.9 CV/CC SIGNAL .....................................................................................................................................46
5.10 PS_OK SIGNAL ..................................................................................................................................46
5.11 SAFE-START AND AUTO-RESTART MODES ..................................................................................47
Auto-Restart Mode......................................................................................................................475.11.1 Safe-Start Mode..........................................................................................................................475.11.2
5.12 OVER-TEMPERATURE PROTECTON (OTP) ...................................................................................47
5.13 LAST SETTING MEMORY..................................................................................................................47
5.14 SERIES OPERATION.........................................................................................................................47
Series Connection for Increased Output Voltage .......................................................................485.14.1 Series Connection for Positive and Negative Output Voltage....................................................495.14.2
5.15 PARALLEL OPERATION....................................................................................................................50
Basic Parallel Operation .............................................................................................................505.15.1 Advanced Parallel Operation......................................................................................................505.15.2
5.16 DAISY-CHAIN CONNECTION............................................................................................................52
5.17 FRONT PANEL LOCKING ..................................................................................................................53
Unlocked Front Panel .................................................................................................................535.17.1 Locked Front Panel.....................................................................................................................535.17.2
CHAPTER 6 REMOTE ANALOG PROGRAMMING ........................................................................54
6.1 INTRODUCTION...................................................................................................................................54
6.2 LOCAL/REMOTE ANALOG CONTROL................................................................................................54
6.3 LOCAL/REMOTE ANALOG INDICATION.............................................................................................54
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND OUTPUT CURRENT..............55
6.5 RESISITIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT.................................56
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT ....................................................57
CHAPTER 7 RS-232 & RS-485 REMOTE CONTROL....................................................................58
7.1 INTRODUCTION...................................................................................................................................58
7.2 CONFIGURATION................................................................................................................................58
Default setting...............................................................................................................................587.2.1 Address Setting.............................................................................................................................587.2.2 RS-232 or RS-485 Selection ........................................................................................................587.2.3 Baud Rate Setting.........................................................................................................................587.2.4 Setting the Unit into Remote or Local Mode.................................................................................58
7.2.5 RS-232/RS-485 Port in Local Mode .............................................................................................597.2.6 Front Panel in Remote Mode........................................................................................................597.2.7
7.3 REAR PANEL RS-232/RS-485 CONNECTOR .....................................................................................59
7.4 CONNECTING POWER SUPPLIES TO RS-232 OR RS-485 BUS.......................................................60
Single Power Supply.....................................................................................................................607.4.1 Multi-Power Supply Connection to RS-232 or RS-485 Bus .........................................................617.4.2
7.5 COMMUNICATION INTERFACE PROTOCOL.....................................................................................61
Data Format..................................................................................................................................617.5.1 Addressing....................................................................................................................................617.5.2 End of Message............................................................................................................................617.5.3 Command Repeat.........................................................................................................................617.5.4 Checksum.....................................................................................................................................627.5.5 Acknowledge.................................................................................................................................627.5.6 Error Message ..............................................................................................................................627.5.7 Backspace ....................................................................................................................................62
7.5.8
7.6 ERROR MESSAGES ............................................................................................................................62
7.7 COMMAND SET DESCRIPTION..........................................................................................................62
General Guide...............................................................................................................................627.7.1 Command Set Categories ............................................................................................................637.7.2 Initialization Control Commands...................................................................................................637.7.3 ID Control Commands ..................................................................................................................637.7.4 Output Control Commands...........................................................................................................637.7.5 Global Output Commands ............................................................................................................657.7.6 Status Control Commands............................................................................................................667.7.7

83-517-000 Rev.A
7.8 STATUS, ERROR AND SRQ REGISTERS...........................................................................................67
General .........................................................................................................................................677.8.1 Conditional Registers....................................................................................................................68
7.8.2 Service Request: Enable and Event Registers.............................................................................697.8.3
7.9 SERIAL COMMUNICATION TEST SET-UP .........................................................................................71
Equipment:....................................................................................................................................717.9.1 PC Set-Up:....................................................................................................................................717.9.2 Power Supply Set-Up:...................................................................................................................717.9.3 Communication Test:....................................................................................................................717.9.4
CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION ....................................................72
8.1 INTRODUCTION...................................................................................................................................72
8.2 SPECIFICATIONS ................................................................................................................................72
0-5V/0-10V OPTION (PN: IS510).................................................................................................728.2.1 4-20mA option (PN: IS420)...........................................................................................................728.2.2
8.3 ISOLATED PROGRAMMING &MONITORING CONNECTOR............................................................73
8.4 SETUP AND OPERATING INSTRUCTIONS........................................................................................74
Setting up the Power Supply for 0-5V/0-10V Isolated Programming and Monitoring ..................748.4.1 Setting up the Power Supply for 4-20mA Isolated Programming and Monitoring........................748.4.2
8.5 PARALLEL OPERATIONWITH ISOLATED ANALOG OPTION...........................................................75
Setting Up The Master Unit ..........................................................................................................758.5.1 Setting Up The Slave Unit ............................................................................................................758.5.2
CHAPTER 9 MAINTENANCE ..............................................................................................................76
9.1 INTRODUCTION...................................................................................................................................76
9.2 UNITS UNDER WARRANTY.................................................................................................................76
9.3 PERIODIC MAINTENANCE..................................................................................................................76
9.4 ADJUSTMENTS AND CALIBRATION ..................................................................................................76
9.5 PARTS REPLACEMENT AND REPAIRS .............................................................................................76
9.6 TROUBLESHOOTING..........................................................................................................................76
9.7 FUSE RATING ......................................................................................................................................77
INDEX (USER’S MANUAL)..................................................................................................................78

83-000-016 Rev. G
WARRANTY
This TDK-Lambda Americas Inc. product is warranted against defects in materials and workmanship for
a period of five years from date of shipment. During the warranty period, TDK-Lambda Americas Inc.
will, at it’s option, either repair or replace products which prove to be defective.
LIMITATION OF WARRANTY
The warranty shall not apply to defects resulting from improper or inadequate usage or maintenance by
the buyer, buyer supplied products or interfacing. The warranty shall not apply to defects resulting from
unauthorized modifications, or from operation exceeding the environmental specifications of the
product, or if the QA seal has been removed or altered by anyone other than TDK-Lambda Americas
Inc. authorized personnel. TDK-Lambda Americas Inc. does not warrant the buyer’s circuitry or
malfunctions of TDK-Lambda Americas Inc. products resulting from the buyer’s circuitry. Furthermore,
TDK-Lambda Americas Inc. does not warrant any damage occurring as a result of the buyer’s circuitry
or the buyer’s - supplied products. THIS LIMITED WARRANTY IS IN LIEU OF, AND TDK-LAMBDA
AMERICAS INC DISCLAIMS AND EXCLUDES, ALL OTHER WARRANTIES, STATUTORY, EXPRESS
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, OR OF CONFORMITY TO MODELS OR SAMPLES.
WARRANTY SERVICE
This product must be returned to an authorized TDK-Lambda Americas Inc. service facility for repairs or
other warranty service. For products returned to TDK-Lambda Americas Inc. for warranty service, the
buyer shall prepay shipping charges to TDK-Lambda Americas Inc. If the unit is covered under the
foregoing warranty then TDK-Lambda Americas Inc. shall pay the shipping charges to return the
product to the buyer. Refer to Section 3.11 for repackaging for shipment.
DISCLAIMER
The information contained in this document is subject to change without notice. TDK-Lambda Americas
Inc. shall not be liable for errors contained in this document or for incidental or consequential damages
in connection with the furnishing, performance or use of this material. No part of this document may be
photocopied, reproduced or translated into another language without the prior written consent of TDK-
Lambda Americas Inc.
TRADEMARK INFORMATION
Genesys™ power supply is a trademark of TDK-Lambda Americas Inc.
Microsoft™ and Windows™are trademarks of Microsoft Corporation.
THE FCC WANTS YOU TO KNOW
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his own expense.
FCC WARNING
Modifications not expressly approved by manufacturer could void the user authority to operate the
equipment under FCC Rules.

83-517-000 Rev. A
2
SAFETY INSTRUCTIONS
CAUTION
The following safety precaution must be observed during all phases of operation, service and repair of this
equipment. Failure to comply with the safety precautions or warnings in this document violates safety standards of
design, manufacture and intended use of this equipment and may impair the built-in protections within.
TDK-Lambda Americas, Inc. shall not be liable for user’s failure to comply with these requirements.
INSTALLATION CATEGORY
The GenesysTM power supply series has been evaluated to INSTALLATION CATEGORY II. Installation category
(over voltage category) II: local level, appliances, portable equipment etc. With smaller transient over voltage than
Installation Category (over voltage category) III.
GROUNDING
This product is a Safety Class 1 instrument. To minimize shock hazard, the instrument chassis must be
connected to an electrical ground. The instrument must be connected to the AC power supply mains through a
three conductor power cable, with the ground wire firmly connected to an electrical ground (safety ground) at the
power outlet.
For instruments designed to be hard-wired to the supply mains, the protective earth terminal must be connected
to the safety electrical ground before another connection is made. Any interruption of the protective ground
conductor or disconnection of the protective earth terminal will cause a potential shock hazard that might cause
personal injury.
WARNING
OUTPUT TERMINAL GROUNDING
There is a potential shock hazard at the RS-232/RS-485, LAN, IEEE, and USB ports
when using power supplies with rated or combined voltage greater than 400V and the
Positive Output of the Power Supply is grounded.
DO NOT connect the Positive Output to ground when using the RS-232/RS-485,
LAN, IEEE, or USB port under this operating condition.
FUSES
Fuses must be changed by authorized TDK-Lambda Americas Inc. service personnel only. For continued
protection against risk of fire, replace only with the same type and rating of fuse. Refer to maintenance
instructions in Chapter 9 for fuse ratings.
INPUT RATINGS
Do not use AC supply, which exceeds the input voltage and frequency rating of this instrument. The input voltage
and frequency rating of the GenesysTM power supply series has one input range. Range is 190-240VAC, 50-60Hz
for single-phase and three-phase 200V models. For safety reasons, the mains supply voltage fluctuations should
not exceed +/-10% of the nominal AC Input voltage.
LIVE CIRCUITS
Operating personnel must not remove the instrument cover. No internal adjustment or component replacement is
allowed by non-TDK-Lambda Americas Inc. qualified personnel. Never replace components with power cable
connected. To avoid injuries, always disconnect power, discharge circuits and remove external voltage source
before touching components.
CAUTION MULTI-POLE FUSING
The GenesysTM power supply units have fuses in all supply conductors. To prevent potential lrisk of hazard
during servicing, the unit shall be fully disconnected from the supply

83-517-000 Rev. A
3
PARTS SUBSTITUTIONS & MODIFICATIONS
Parts substitutions and modifications are allowed by authorized TDK-Lambda Americas Inc. service personnel
only. For repairs or modifications, the instrument must be returned to an authorized TDK-Lambda Americas Inc.
Service facility.

83-517-000 Rev. A
4
SAFETY INSTRUCTIONS
ENVIRONMENTAL CONDITIONS
The GenesysTM Power Supply series safety approval applies to the following operating conditions:
*Indoor use *Ambient temperature: 0°C to 50°C
*Maximum relative humidity: 80% (no condensation) *Altitude: up to 3000m
*Pollution degree 2
Do not use this product in environments with strong Electromagnetic field, corrosive gas and
conductive materials.
ATTENTION Observe Precautions for handling Electrostatic Sensitive Devices.
CAUTION Risk of Electrical Shock
Instruction manual symbol. The instrument will be marked with this symbol when it is necessary
for the user to refer to the instruction manual.
Indicates hazardous voltage.
Indicates ground terminal.
Protective Ground Conductor Terminal must be connected to Earth Ground.
Off (Supply)
On (Supply)
The WARNING sign denotes a hazard. An attention to a procedure is called.
Not following procedure correctly could result in personal injury.
A WARNING sign should not be skipped and all indicated conditions must be
fully understood and met.
The CAUTION sign denotes a hazard. An attention to a procedure is called. Not following
procedure correctly could result in damage to the equipment. Do not proceed beyond a CAUTION
sign until all indicated conditions are fully understood and met.
FCC COMPLIANCE NOTICE:
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

83-517-000 Rev. A
5
FRENCH
CONSIGNES DE SECURITE
ATTENTION
Les consignes de sécurité suivantes doivent être observées pendant toutes les phases de l'utilisation, entretien et
réparations de cet équipement. Le non-respect des consignes de sécurité et des avertissements dans ce
document viole les normes sécurité de conception, fabrication et utilisation prévue de cet équipement et peut
compromettre les protections incorporées en lui.
TDK-Lambda Americas Inc. ne sera pas responsable des conséquences si l'utilisateur ne respecte pas ces
consignes.
CATEGORIE D'INSTALLATION
Les alimentations GenesysTM ont été classées dans CATEGORIE INSTALLATION II. Catégorie installation
(catégorie surtension) II : utilisation locale, appareils, équipement portable, etc. Avec des surtensions transitoires
plus faibles que celles de la catégorie installation (catégorie surtension) III.
MISE A LA TERRE
Ce produit est un instrument Classe 1 Sécurité. Pour minimiser le risque de choc électrique, son châssis doit être
raccordé à une terre électrique. L'instrument doit être raccordé à l'alimentation principale AC par un câble à trois
conducteurs, le conducteur de terre étant raccordé à une terre électrique (terre sécurité) sur la prise électrique.
Pour les instruments conçus pour être raccordés à l'alimentation électrique principale, la borne de terre doit être
raccordée à la terre électrique de sécurité avant d'établir une autre connexion. Si le conducteur de terre est coupé
ou si la borne de terre est débranchée, il y a un risque de choc électrique pouvant provoquer des blessures.
ATTENTION-DANGER
MISE A LA TERRE DES BORNES DE SORTIE
Il y a un danger de choc électrique sur les ports RS-232/RS-485, LAN,
IS420/IS520 et IEMD lorsqu'on utilise des alimentations électriques ayant à
elles seules ou au total une tension supérieure à 400V et si la sortie positive ou
negative de l'alimentation est raccordée à la terre.
Ne pas connecter la sortie positive ou negative à la terre lorsque vous utilisez le
RS-232/RS-485, LAN, IEMD ou USB sous cette condition de fonctionnement.
FUSIBLES
Les fusibles ne doivent être remplacés que par des techniciens d'entretien agréés TDK-Lambda Americas
Inc. Pour assurer une protection continue contre le risque d'incendie, remplacez les fusibles par des fusibles
de même type et de même capacité.
ALIMENTATION PRINCIPALE
N'utilisez pas une alimentation AC dont la tension et la fréquence dépassent les valeurs nominales de cet
instrument. La tension et la fréquence nominales des alimentation GenesysTM correspondent à un intervalle
selon le modèle commandé. Les intervalle est 190-240VAC, 50-60Hz. Pour des raisons de sécurité, la
tension d'alimentation principale ne doit pas fluctuer en dehors des intervalles ci-dessus.
CIRCUITS SOUS TENSION
Le personnel d'exploitation ne doit pas enlever le couvercle de l'instrument. Le réglage ou le remplacement
des composants internes ne peut être effectué que par un personnel qualifié TDK-Lambda Americas Inc. Ne
remplacez jamais les composants lorsque le câble d'alimentation est connecté. Pour éviter les blessures,
débranchez toujours l'alimentation, déchargez les circuits et retirez la source de tension extérieure avant de
toucher les composants.

83-517-000 Rev. A
6
CONSIGNES DE SECURITE
SUBSTITUTIONS ET MODIFICATIONS DE PIECES
Les substitutions et modifications de pièces ne peuvent être effectuées que par les techniciens d'entretien
agréés TDK-Lambda Americas Inc. Pour les réparations ou les modifications, l'instrument doit être renvoyé à
un centre d'entretien agréé TDK-Lambda Americas Inc.
CONDITIONS ENVIRONNEMENTALES
L'approbation sécurité des alimentations GenesysTM s'applique aux conditions opératoires suivantes :
*Utilisation en intérieur *Température ambiante : 0°C à 50°C
*Humidité relative maximum : 80% (sans condensation) *Altitude : 3000m maximum
*Pollution degré 2
PRECAUTION. Observez les précautions pour manipuler les composants sensibles à
l'électricité statique.
ATTENTION. Risque de choc électrique
Symbole dans le manuel d'instructions. Ce symbole sera marqué sur l'instrument lorsque
l'utilisateur doit consulter le manuel d'instructions.
Signale une tension dangereuse.
Signale une borne de terre.
La borne du conducteur de terre de protection doit être connectée à la terre électrique.
Coupée (alimentation)
Branchée (alimentation)
Le symbole WARNING signale un danger. Il attire l'attention sur une procédure.
Si la procédure n'est pas suivie correctement, il peut en résulter des blessures.
Le symbole WARNING (Attention-danger) ne doit pas être ignoré et toutes les conditions
indiquées doivent être bien comprises et respectées.
Le symbole CAUTION (Attention) signale un danger. Il attire l'attention sur une procédure. Si la
procédure n'est pas suivie correctement, l'équipement peut être endommagé. Ne continuez pas
après avoir rencontré le symbole CAUTION tant que vous n'avez pas parfaitement compris et
respecté les conditions indiquées.
NOTE CONCERNANT LA CONFORMITE FCC :
Nota : Cet équipement a été testé et s'est avéré conforme aux limites pour un appareil
numérique Classe A selon la part 15 des règles FCC. Ces limites sont conçues pour assurer une
protection raisonnable contre les interférences dangereuses lorsque l'équipement est utilisé dans
un environnement commercial. Cet équipement génère, utilise et peut rayonner des fréquences
radio et, s'il n'est pas installé et utilisé conformément au manuel d'instructions, il peut provoquer
des interférences dangereuses pour les communications radio. L'utilisation de cet équipement
dans une zone résidentielle provoquera probablement des interférences nocives, et dans ce cas
l'utilisateur doit prendre des mesures pour les supprimer à ses propres frais.

83-517-000 Rev. A
7
GERMAN
SICHERHEITSVORSCHRIFTEN
VORSICHT
Die folgenden Sicherheitsvorschriften müssen in allen Phasen des Betriebs, der Wartung und der Reparatur der
Anlage eingehalten werden. Eine Missachtung der Sicherheitsvorschriften und Warnhinweise aus diesem
Handbuch führt zur Verletzung der bestehenden Sicherheitsstandards für Design, Produktion und der
zweckbestimmten Verwendung der Anlage und kann die integrierten Schutzvorrichtungen beschädigen.
TDK-Lambda Americas Inc. ist nicht haftbar für Schäden, die durch Missachtung dieser Sicherheitsvorschriften
entstehen können.
INSTALLATIONSKATEGORIE
Die GenesysTM Reihe der Netzgeräte wurde in die INSTALLATIONSKATEGORIE II eingeteilt.
Installationskategorie (Überspannungskategorie) II: die lokale Ebene, Geräte, tragbare Anlagen, etc. mit kleineren
vorübergehenden Überspannungen als die Installationskategorie (Überspannungskategorie) III.
ERDUNGSKONZEPT
Dieses Produkt ist ein Gerät der Schutzklasse 1. Zur Vermeidung von gefährlichen Energieinhalten und
Spannungen, ist das Gehäuse des Gerätes an eine Schutzerde anzuschließen. Das Gerät muss über ein
Dreileiterstromkabel an die AC-Hauptstromversorgung angeschlossen werden, wobei das Erdungskabel fest mit
einer elektrischen Erdung (Schutzerde PE) am Stromanschluss verbunden sein muss.
Bei Festverdrahtung der Geräte ist sicherzustellen, dass der PE-Anschluss an die elektrische Schutzerde
angeklemmt wird, bevor das Gerät an die Stromversorgung angeschlossen wird. Jede Unterbrechung des PE-
Leiters oder die Trennung der PE-Verbindung kann einen möglichen elektrischen Schlag hervorrufen, der
Personenschäden zur Folge haben kann.
WARNUNG
ERDUNG DER AUSGANGSANSCHLÜSSE
Es besteht die Gefahr von möglichen Schlägen an der RS-232/RS-485, LAN, IS420/IS520 und
den IEMD-Anschlüssen, wenn Netzgeräte mit höheren Nenn- oder kombinierten Spannungen
als 400V verwendet werden und die positive oder negative Ausgangsspannung der Netzgeräte
geerdet wurde.
Schließen Sie den positiven oder negative Ausgang an Masse, wenn die RS-232/RS-485, LAN,
IEMD der USB unter diesem Betriebszustand mit.
SICHERUNGEN
Sicherungen dürfen nur durch von TDK-Lambda Americas Inc. zugelassenes Personal ausgewechselt werden.
Für anhaltenden Brandschutz dürfen die Sicherungen nur mit baugleichen Sicherungen mit der gleichen Leistung
ersetzt werden.
EINGANGSLEISTUNG
Verwenden Sie keine AC-Spannung, die die Eingangsleistung und Frequenzrate dieses Gerätes übersteigt. Die
Eingangsspannung und Frequenzrate der GenesysTM Reihe der Netzgeräte verfügt über eins Eingangsbereiche,
je nach bestelltem Bautyp. Die Bereich ist 190-240VAC, 50-60Hz. Aus Sicherheitsgründen sollten die
Spannungsschwankungen der Hauptstromversorgung den oberen Spannungsbereich nicht übersteigen.
SPANNUNGSFÜHRENDE TEILE
Die Geräteabdeckung darf nicht durch Betriebspersonal entfernt werden. Interne Modifikationen sowie
Bauteileaustausch sind nur durch von TDK-Lambda Americas Inc. qualifiziertes Personal erlaubt. Vor dem
Austausch von Komponenten muss immer die Versorgungsspannung getrennt werden. Um Personenschäden zu
vermeiden, muss vor dem Kontakt mit dem Gerät immer die Stromversorgung unterbrochen, die Stromkreise
entladen und externe Spannungsquellen entfernt werden.

83-517-000 Rev. A
8
SICHERHEITSVORSCHRIFTEN
ERSATZTEILE & MODIFIKATIONEN
Ersatzteile und Modifikationen dürfen nur durch von TDK-Lambda Americas Inc. zugelassenes Personal
durchgeführt werden. Für Reparaturen oder Modifikationen muss das Gerät an einen autorisierten TDK-Lambda
Americas Inc. Vertriebspartner geschickt werden.
UMGEBUNGSBEDINGUNGEN
Die Sicherheitsbestätigung der GenesysTM Netzteilserie gilt für die folgenden Betriebszustände:
* Gebrauch im Innenbereich *Umgebungstemperatur: 0°C bis 50°C
*Maximale relative Luftfeuchtigkeit: 80% (keine Kondensation) *Höhe: bis zu 3.000m
* Verschmutzungsgrad 2
ACHTUNG Beachten Sie die Vorsichtsmaßnahmen im Umgang mit elektrostatisch gefährdeten
Bauteilen.
VORSICHT Gefahr von elektrischen Schlägen.
Symbol der Bedienungsanleitung. Dieses Symbol wird am Gerät angezeigt, wenn der Benutzer
die Bedienungsanleitung lesen soll.
Weist auf eine gefährliche Spannung hin.
Weist auf eine Erdungsklemme hin.
PE-Leiterklemme must an Erde angeschlossen werden.
Aus (Versorgung)
Ein (Versorgung)
Das WARNSYMBOL deutet auf eine Gefahr hin. Die Aufmerksamkeit wird auf ein Verfahren
gelenkt.
Eine Missachtung der Einhaltung des Verfahrens kann zu Personenschaden führen.
Eine WARNUNG darf nicht übergangen werden und alle angezeigten Umstände müssen
vollkommen verstanden und eingehalten werden.
Das VORSICHTSYMBOL deutet auf eine Gefahr hin. Die Aufmerksamkeit wird auf ein
Verfahren gelenkt. Eine Missachtung der korrekten Einhaltung des Verfahrens kann zu
Materialschaden führen. Ein VORSICHTSYMBOL darf nicht übergangen werden bis alle
angezeigten Umstände vollkommen verstanden und eingehalten werden.
FCC EINHALTUNGSVERMERK:
Hinweis: Das Gerät wurde geprüft und erfüllt die Grenzwerte für ein digitales Gerät der Klasse A
gemäß Teil 15 der FCC-Regeln. Diese Grenzwerte wurden definiert, um angemessenen Schutz
vor gefährlichen Störungen zu bieten, wenn das Gerät im kommerziellen Umfeld betrieben wird.
Dieses Gerät kann Funkfrequenzenergie erzeugen, verwenden und ausstrahlen und kann,
sofern es nicht gemäß dem Benutzungshandbuch installiert wurde, gefährliche Störungen im
Funkverkehr verursachen. Es ist wahrscheinlich, dass dieses Gerät in Wohngebieten zu
schädlichen Störungen führt, die in solchen Fällen auf Kosten des Benutzers behoben werden
müssen.

83-517-000 Rev. A
9
ITALIAN
NORME DI SICUREZZA
ATTENZIONE
La seguente precauzione di sicurezza deve essere osservata a tutti gli stadi del funzionamento, della
manutenzione e della riparazione di questa apparecchiatura. L'inosservanza delle precauzioni o delle avvertenze
di sicurezza contenute in questo documento viola gli standard di sicurezza della progettazione, della produzione e
dell'uso previsto di questa apparecchiatura, e può compromettere i dispositivi di protezione in essa incorporati.
TDK-Lambda Americas Inc. non si assume alcuna responsabilità per il mancato rispetto di questi requisiti da
parte dell'utente.
CATEGORIA DI INSTALLAZIONE
La serie di alimentatori Genesys™ è stata valutata e risulta conforme alla CATEGORIA DI INSTALLAZIONE II.
Categoria di installazione (categoria di sovratensione) II: livello locale, elettrodomestici, apparecchiature portatili
ecc. Con sovratensioni transitorie inferiori alla Categoria di installazione (categoria di sovratensione) III.
MESSA A TERRA
Questo prodotto è uno strumento di Classe di sicurezza 1. Per minimizzare il pericolo di scosse elettriche, il telaio
dello strumento deve essere collegato a una terra elettrica. Lo strumento deve essere collegato alla rete di
alimentazione a CA mediante un cavo a tre conduttori, con il filo di terra ben collegato a una terra elettrica (terra
di sicurezza) in corrispondenza della presa di corrente.
Per strumenti progettati per il cablaggio alla rete di alimentazione, il terminale protettivo di terra va collegato alla
terra elettrica di sicurezza prima di procedere ad altri collegamenti. Eventuali interruzioni del conduttore protettivo
di terra, o scollegamenti del terminale protettivo di terra, porteranno al rischio di scossa elettrica e di conseguente
potenziale infortunio.
AVVERTENZA
MESSA A TERRA DEI TERMINALI DI USCITA
Vi è rischio di scossa elettrica in corrispondenza delle porte R-S232/RS-485, LAN, IS420/IS520 e
IEMD se si utilizzano alimentatori con tensione nominale o combinata oltre 400V e con l'Uscita
positiva o negativa dell'alimentatore messa a terra.
Non collegare l'uscita positiva o negativa a terra quando si utilizza la RS-232 / RS-485, LAN, IEMD
o USB in questa condizione di funzionamento.
FUSIBILI
I fusibili devono essere sostituiti unicamente da addetti autorizzati di TDK-Lambda Americas Inc. Per una
protezione continua dal rischio di incendi, sostituire sono con fusibili di tipo e di potenza nominale identici.
POTENZE NOMINALI IN INGRESSO
Non usare un'alimentazione a CA che superi la tensione in ingresso e la potenza nominale di frequenza di questo
strumento. La tensione in ingresso e la potenza nominale di frequenza della serie di alimentatori GenesysTM
presentano uno bande di ingressi, a seconda del tipo di modello ordinato. Le band è: 190-240VAC, 50-60Hz. Per
ragioni di sicurezza, eventuali fluttuazioni nella tensione di rete non devono superare il campo di potenze nominali
suddetto.
CIRCUITI SOTTO TENSIONE
Nessun addetto deve mai rimuovere il coperchio dello strumento. Le regolazioni interne e la sostituzione dei
componenti sono consentite unicamente al personale qualificato di TDK-Lambda Americas Inc. Non sostituire mai
un componente con il cavo elettrico ancora collegato. A prevenzione degli infortuni, staccare sempre la corrente,
scaricare i circuiti e scollegare le fonti di tensione esterne prima di toccare i componenti.

83-517-000 Rev. A
10
NORME DI SICUREZZA
SOSTITUZIONI E MODIFICHE DEI COMPONENTI
I componenti devono essere sostituiti o modificati unicamente da addetti autorizzati di TDK-Lambda Americas Inc.
Per riparazioni o modifiche, restituire lo strumento al centro assistenza di TDK-Lambda Americas Inc.
CONDIZIONI AMBIENTALI
L'approvazione della sicurezza della serie di alimentatori Genesys™ è valida in presenza delle condizioni d'uso
seguenti:
*Uso in interni *Temperatura ambiente: 0ºC - 50ºC
*Umidità relativa massima: 80% (zero condensa) *Altitudine: fino a 3000m
*Inquinamento grado 2
ATTENZIONE Osservare le precauzioni su come maneggiare i dispositivi sensibili alle scariche
elettrostatiche.
ATTENZIONE Rischio di scossa elettrica
Simbolo del manuale delle istruzioni. Lo strumento sarà contrassegnato da questo simbolo
ovunque l'utente deve fare riferimento al manuale delle istruzioni.
Indica tensioni pericolose.
Indica il terminale di terra.
Il terminale del conduttore protettivo di terra deve essere collegato alla messa a terra.
Spento (Alimentazione)
Acceso (Alimentazione)
Il simbolo di AVVERTIMENTO denota un periodo. È necessario prestare attenzione alla
procedura.
Il mancato rispetto della procedura può sfociare in un infortunio.
Non ignorare alcun simbolo di AVVERTIMENTO. Tutte le condizioni indicate devono essere
pienamente comprese e rispettate.
Il simbolo di ATTENZIONE denota un pericolo. È necessario prestare attenzione alla procedura.
Il mancato rispetto della procedura può sfociare in danni per l'apparecchiatura. Non procedere
oltre un simbolo di ATTENZIONE senza prima avere pienamente compreso e rispettato tutte le
condizioni indicate.
AVVISO DI CONFORMITÀ FCC:
NB: Questa apparecchiatura è stata testata ed è risultata conforme ai limiti per i dispositivi
digitali di Classe A, ai sensi della parte 15 dei Regolamenti FCC. Tali limiti sono formulati per
offrire ragionevole protezione dalle interferenze pericolose quando l'apparecchiatura viene
azionata in ambienti commerciali. Questa apparecchiatura genera, usa e può irradiare energia a
radiofrequenza; se non viene installata ed utilizzata attenendosi al manuale delle istruzioni, può
causare interferenze pericolose per le radiocomunicazioni. È probabile che l'uso di questa
apparecchiatura in zone residenziali provochi interferenze pericolose. In tal caso, l'utente dovrà
rettificare a proprie spese tali interferenze.