Team C Jekyll TR02EVO User manual

1:10 SCALE 2WD ELECTRIC BUGGY
TR02EVO CHASSIS

Notice
This manual is written in english language only. If you need a manual in your language please visit our
website or contact your distributor!
Diese Anleitung wurde in englischer Sprache verfasst. Sollten sie eine Anleitung in ihrer Sprache
benötigen, besuchen sie unsere website oder konaktieren sie ihren Vertriebsagenten.
Questo manuale è stato scritto in inglese. Se avete bisogno del manuale nella tua lingua, si prega di
visitare il nostro sito web o contattate il proprio distributore.
Este manual está escrito en Inglés. Si necesita el manual en su idioma, por favor visite nuestro sitio
web o contacte con su distribuidor.
Ce manuel est écrit en langue anglaise. Si vous avez besoin d'un manuel dans votre langue
s'il vous plaît visitez notre site web ou contactez votre distributeur!
Deze handleiding is geschreven in het Engels taal beschikbaar. Als u een handleiding in uw eigen
taal kunt u terecht op onze website of neem contact op met uw distributeur!
Thank you for purchasing this Jekyll Offroad Buggy by Team C. This manual shows instructions and
tips to built and maintain your Jekyll. Please take some time to read through to get familiar with the
shown steps.
We continually improve our products, due to that, actual parts my be different to the illustrations.
Please check our website for the latest versions manuals and tips before you start to built this model.
Generall Information
THIS IS NOT A TOY!
Not suitable for children under 14 years of age without adult supervision.
This is a high performance vehicle, for safety reason don’t run on public streets, in crowded areas,
environmentally areas or near children or animals.
This model contains rotationg parts and parts which become hot during operation. Care must been
taken to avoid damage or injuries.
This product may require some assembly and routine maintance.
This product is covered by warranty based on material defectives. Crash damage or maintenance
failures are not covered under warranty.
Batteries should be used in good condition only, and need to be fully charged.
Nitro models should be driven outside of buildings only. Inhaling exhaust gases could cause health
damage.
Keep chemicals stored out of the range of small children.
Make sure your model and equipment is in perfect condition before you use it, to ensure savety
and fun while driving.

DIGITAL
PROPORTIONAL
RADIO CONTROL
SYSTEM
DIGITAL
PROPORTIONAL
RADIO CONTROL
SYSTEM
反向开关
Transmitter Preparation
27MHzTransmitter Crystal （TX）
Transmitter crystal(TX)
Power Switch
ON
OFF
Antenna
Extend the antenna to the maximum
Length for best performance
The crystal can be replaced to change frequencies.
Note : You must also change receiver crystals!
Do not use AM crystals
Receiver crystal(RX)
Steering Trim
To be used for trimming the steering
operation
Throttle Trim
Steering Dual Rate
To be used to adjust steering servo throw
AA Alkaling Batteries
8X
Open battery cover at the bottom of transmitter.
Install batteries. Follow the direction of batteries
designated in the inside of battery box.
Transmitter Battery Installation
This switch is used for optional parts.
3ch Switch
Reverse Switch
Low Batteries(Light Blinks)
Good Batteries
Battery Level Indicator
Left turn Straight (neutral)
Right turn
Brake
Forward Stop(Neutral)
To be used for throttle operation
Throttle Trigger
Battery Cover
Servo Factory Settings
1
1
2
3
2
To be used for trimming the throttle
operation
3
4
4

Transmitter Preparation
馬達
發送機
Battery
A new Ni-MH battery must be charged before it is used.Refer to the charger instruction manual for charging.
Set up the radio control system as indicated below。
6
5
8
Servo
Receiver
Transmitter
10
4
Switch
7
9
Electronic Speed
Controller
Motor
DIGITAL
PROPORTIONAL
RADIO CONTROL
SYSTEM
11
2
ON
OFF
6
10
ON
OFF
5
8
1
3
Tools required
Needie Nose Pllers Awi Grease Screw Cement Instant Glue
Hex Wrench
Ball differential Grease(Clear)
Molybdenum Grease(Black)
Hex Wrench
SP KINFE EDGE REAMER
No need to pre-drill precise holes
(1mm to 15mm)can be drilled
Wire Cutters
Sharp Hobby knife
ROUND CUTTER&SANDER
For trimming bodies!
2
Start
Finish
Install batteries.(Transmitter)
Extend the antenna.(Transmitter)
Connect the battery
Extend the antenna.(Reveiver)
Center the trims.
Switch on.(Transmitter)
Switch on.(Reveiver)
Make sure the servos are in command.
Switch off.(Reveiver)
Switch off.(Transmitter)
Retract the antenna(Transmitter)
1
8
7
2
5
3
4
6
9
10
11

T02059 Ball stud - long
……………………2
T02104
T02059
T02109
T02104
T02126
1
L R
2 3
1
3
2
1
2
4
5
Front Suspension
Front Suspension
T02056 3x34.5 Hinge pin front inner
………………………………4
………………………………2
T02056 2.3 E-ring
……………4
T02083 M3x15 Screw
3
1
2 Assemble in the specified order L R
Assemble left and right sides the same way
T02125
T02037
T02056
T02056
T02083
T02008
T02056
T02056
T02056
T02056
1

T02060 Ball stud - short
T02079 5x10x4
Contain oil ball
T02079
T02079
T02060
T02060
T02122
T02123
T02128
bearing
5
6
L R
3
1
2
3
1
2
4
5
3
1
2
1
2
4
3
5
6
7
8
T02082 M3x8 Screw
………………2
T02082 M3x10 Screw
………………6
……………8
T02054 2.3 E-ring
……………………4
…………2
…………………4
T02054 3x27.5 Hinge pin front outer
…………4
T02082(3x8)
T02042 2x9.8 Shaft
…………2
3
1
2 Assemble in the specified order
Front Suspension
Front Suspension
L R
Assemble left and right sides the same way
T02042 4.0 E-ring
T02082(3x10)
T02082(3x10)
T02082(3x10)
T02082(3x10)
T02054
T02054
T02042
TU0254
T02042
T02042
T02054
T02054
T02054
T02054
<Right>
<Left>
T02144
3

T02060 Ball stud - short
T02079 5x10x4
Contain oil ball
T02079
T02079
T02060
T02060
T02122
T02123
T02128
bearing
5
6
L R
3
1
2
3
1
2
4
5
3
1
2
1
2
4
3
5
6
7
8
T02082 M3x8 Screw
………………2
T02082 M3x10 Screw
………………6
……………8
T02054 2.3 E-ring
……………………4
…………2
…………………4
T02054 3x27.5 Hinge pin front outer
…………4
T02082(3x8)
T02042 2x9.8 Shaft
…………2
3
1
2 Assemble in the specified order
Front Suspension
Front Suspension
L R
Assemble left and right sides the same way
T02042 4.0 E-ring
T02082(3x10)
T02082(3x10)
T02082(3x10)
T02082(3x10)
T02054
T02054
T02042
TU0254
T02042
T02042
T02054
T02054
T02054
T02054
<Right>
<Left>
T02144
3

T02112 4.8mm Ball End(Long)
T02045 3x54 Turnbuckle
…………8
………4
T02117 5mm Plastic Ball stud
T02045
T02112
T02112
T02117
T02117
T02129
Front Upper(Right)
Front Upper (Left)
Steering Tip
approx.38mm
approx.38mm
approx.34mm
1:1
1:1
1:1
x2
x1
x1
7
9
………4
T02082 M3x10 Screw
……2
T02082 M3x22 Screw
……………2
Front Suspension
Front Suspension
T02082(M3x22)
T02082(M3x22)
T02082(M3x10)
8 Front Suspension
x1
Assemble as many times as specified
1:1
True-to -scale diagram
4

T02007 M2.5x25 Screw
……1
T02048 2.37mm Ball
………………12
T02007 M2.5 Nylon Nut
……………2
……………1
T02078 10x15x4
Contain oil ball
……………2
T02049 17x23x1 Washer
……………2
T02007(2.5x25)
T02077(5x8x2.5)
T02078(10x15x4)
T02078(10x15x4)
T02007
T02007(M2.5)
T02047
T02046
T02046
T02077(5x8x2.5)
T02049(17x23x1)
T02049(17x23x1)
T02048(2.37)
T02004
T02077 5x8x2.5 Contain oil ball
bearing
bearing
T02050(2.6x6x3)
Differential Gear
Apply grease
10
5

<Right>
<Left>
T02079 5x10x4 Contain oil ball
…………………4
T02051 5x16.8 idler gear shaft
T02041 5x8x6.7 Top shaft spacer
…………………1
……………………1
T02121
T02121
T02079
T02079
T02003
T02079
T02079
T02052
T02041
T02051
T02140
Bearing
12
11
…………1
T02082 M3x12 Screw
………4
T02082 M3x25 Screw
Apply grease
Screw
Cement
Screw
Cement
Screw
Cement
Apply threadlocker(screw cement)
Transmission
Motor mounts
T02082(3x12)
T02082(3x25)
T02082(3x25)
6

approx.18mm
T02082 M3x10 Screw
………………4
……2
T02117 5mm Plastic Ball stud
………………………2
T02082(M3x22)
T02117
T02082 M3x22 Screw
T02084
T02040
T02134
T02134
T02038
T02038
T02119
T02082(M3x10)
T02082(M3x22)
T02117
T02130
14
13 Main Gear
Rear Damper Tower
7
T02108

T02059 Ball stud - long
……………2 …………4
T02082 M3x10 Screw
…………2
T02083 M3x8 Screw
T02125
T02009
T02083
T02083
T02059
T02127
16
15 Rear Bulkhead
Rear Chassis
T02082 T02082
8

T02125
T02105
18
17
L R
………………………………2
T02083 M3x8 Screw
T02055 3x48 Hinge pin Rear inner
……2
…………2
T02083 M3x10 Screw
Rear Suspension
Rear Suspension
L R
Assemble left and right sides the same way
T02055
T02083
T02083
T02083
9

T02109
19
20 3
1
2
1
3
2
4
5
……………2
T02082 M3x10 Screw
……………2
T02082 M3x8 Screw
…………2
T02082 M3x10 Screw
…………4
Rear Shock Tower & Rear Fender
3
1
2 Assemble in the specified order
Screws which were semi tightened in P9
T02083 M3x8 Screw
17
T02083(3x8)
T02082
T02083
T02082(3x10)
T02082(3x8)
Rear Transmission
10

L R
<Right>
<Left>
T02060 Ball stud - short
…………………2
T02115 2x9.8 Shaft
T02079 5x10x4 Contain oil ball
……………4
T02124 3.1x6x1 Plastic Washer
T02135
T02079
T02079 T02115
…………………2
T02060
T02124
T02124
bearing
21
22
L R
T02057 3x30.5 Hinge pin Rear outer
…………………………4
…………2
T02057 2.3 E-ring
………………………2
Rear Suspension
L R
Assemble left and right sides the same way
Apply grease
Rear Suspension
T02057
T02057
T02057
11
TU0254

23
25
T02112 4.8mm Ball End(Long)
T02045 3x54 Turnbuckle
…………………………4
…………………………2
…………2
T02083 M3x8 Screw
…………2
T02083 M3x10 Screw
Rear Suspension
Main Chassis
T02083(3x10)
T02108
T02083(3x8)
T02083(3x10)
T02108
T02108
T02108
approx.35mm
1:1 x2
24
Rear Suspension
Right Upper
T02045 T02112
T02112
x2
Assemble as many times as specified
1:1
True-to -scale diagram
12

26
Front
27
x2 x2
F R
x2
3
2
1
2
Shock Absorber
Shock Absorber
Rear
……………………4
…………………………8
T02138 / T02139 2.3 E-ring
T02068 9.9x2.5 Shock Piston
…………………4
T02069 2.8x1.9 O-ring
…………………8
T02069 3.1x1mm Plastic Washer
T02137 5.8x6 Ball stud
T02114 5.8 Ball End
…………………4
…………………………4
T02066 & T02067 8x1 O-ring
T02138(Short)
Put a little oil
Put a little oil
T02139(Long)
T02068
T02138
T02138
T02139
T02139
T02068 T02067
T02067
……………………4
T02067(Long)
T02066
T02066
T02066(Short)
1
Put the oil
for Front(Short)
for Rear(Long)
T02069(2.8x1.9)
T02069(3x1mm)
T02069(2.8x1.9)
T02069
T02069(2.8x1.9)
T02069(3x1mm)
T02069(2.8x1.9)
T02069
T02137
T02114
T02137
T02114
T02066 / T02067
ohS rebrosbAkc
liO
F R
x2
for Front(Short)
for Rear(Long)
F R
Assemble front and rear sides the same way
3
1
2 Assemble in the specified order
x2
Assemble as many times as specified
13

28
29
x2
x2
3
2
1
1
2
3
L R
T02084 M3 Nylon Nut
…………2 ……2
T02082 M3x15 Screw
Shock Absorber
Front Suspension
for adjusting the spring tension
Compress the spring and install
Front
Rear
Short
Long
Short
T02072(Long)
T02071(Short)
T02114
1
T02114
T02067
T02066
T02140 3mm adjuster ring
…………4
T02084
T02082
T02140
T02140
3
1
2 Assemble in the specified order
x2
Assemble as many times as specified
L R
Assemble left and rear sides the same way
14

30
31
L R
T02084 M3 Nylon Nut
…………2 ……2
T02082 M3x15 Screw
T02081 3x7x0.8 Washer
T02083 M3x8 Screw T02082 M3x5 Screw
T02141 M3x3 Screw
…………2
………2
…………1
………2
Rear Suspension
3
2
1
Motor
Long
T02082
T02084
1 2
3
4
5
T02083
T02081
T02141 T02082
T02120
Motor
L R
Assemble left and rear sides the same way
3
1
2 Assemble in the specified order
15

32
33
Steering Servo
3
2
1
1
2
3
4
Radio
Electronic speed controller
T02087
Receiver
Double-sided Tape
T02113
T02110(25T)
T02111
T02136
T02081
T02082
T02082
T02081
Double-sided Tape
T02116
Steering Servo-H(24T) Steering Servo-S(23T)
Select for your servo
Sanwa servo T02111
T02087
T02082(2.6x8)
T02113 4.8 Ball End(Short)
……………2
T02113 M3x10 Screw
……………1
T02081 3x7x0.8 Washer
………………4
T02082 M3x8 Screw
…………4
T02136 Ball stud - silvery
…………………1
……2
T02083 M3x8 Screw T02116 1.5 Servo spacer
……2
T02082 M2.6x8 Screw
…………1
T02083
Steering Servo
X
M3x3
3
1
2
Assemble in the specified order
X Must be purchased separately
16