Team Losi BND SUPER BAJA REY User manual

Before operating this vehicle, please read all printed materials thoroughly.
Horizon Hobby is not responsible for inadvertent errors in this manual.
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE DI ISTRUZIONI

EN
2SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
Age Recommendation: Not for children under 14 years. This is not a toy.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in dam-
age to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and
responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with
incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and mainte-
nance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon
Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM
or Spektrum technology.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature,
visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
Your new Horizon Hobby vehicle has been designed and built with a combination of
waterproof and water-resistant components to allow you to operate the product in many
“wet conditions,” including puddles, creeks, wet grass, snow and even rain.
While the entire vehicle is highly water-resistant, it is not completely waterproof and your
vehicle should NOT be treated like a submarine. The various electronic components used in the
vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, how-
ever, most of the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts
in the electrical cables, will be susceptible to corrosion if additional maintenance is not
performed after running in wet conditions. To maximize the long-term performance of your
vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions
Maintenance” section below must be performed regularly if you choose to run in wet
conditions. If you are not willing to perform the additional care and maintenance
required, then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and
complying with the following precautions could result in product malfunction
and/or void the warranty.
GENERAL PRECAUTIONS
• Read through the wet conditions maintenance procedures and make sure that you
have all the tools you will need to properly maintain your vehicle.
• Not all batteries can be used in wet conditions. Consult the battery manufacturer before
use. Caution should be taken when using Li-Po batteries in wet conditions.
• Most transmitters are not water-resistant. Consult your transmitter’s manual or the
manufacturer before operation.
• Never operate your transmitter or vehicle where lightning may be present.
• Do not operate your vehicle where it could come in contact with salt water (ocean
water or water on salt-covered roads), contaminated or polluted water. Salt water
is very conductive and highly corrosive, so use caution.
• Even minimal water contact can reduce the life of your motor if it has not been certified
as water-resistant or waterproof. If the motor becomes excessively wet, apply very light
throttle until the water is mostly removed from the motor. Running a wet motor at high
speeds may rapidly damage the motor.
• Driving in wet conditions can reduce the life of the motor. The additional resistance of
operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or
larger spur gear. This will increase torque (and motor life) when running in mud, deeper
puddles, or any wet conditions that will increase the load on the motor for an extended
period of time.
WET CONDITIONS MAINTENANCE
• Drain any water that has collected in the tires by spinning them at high speed. With the
body removed, place the vehicle upside down and pull full throttle for a few short bursts
until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any loose or hanging objects
away from rotating parts when performing the above drying technique.
• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can
of compressed air, blow out any water that may be inside the recessed connector housing.
• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a
garden hose. Avoid rinsing the bearings and transmission.
NOTICE: Never use a pressure washer to clean your vehicle.
• Use an air compressor or a can of compressed air to dry the vehicle and help remove
any water that may have gotten into small crevices or corners.
• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing
light oil. Do not spray the motor.
• Let the vehicle air dry before you store it. Water (and oil) may continue
to drip for a few hours.
• Increase the frequency of disassembly, inspection and lubrication of the following:
- Front and rear axle hub assembly bearings.
- All transmission cases, gears and differentials.
- Motor—clean with an aerosol motor cleaner and re-oil the bushings
with lightweight motor oil.
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
As the user of this product, you are solely responsible for operating in a manner that does not
endanger yourself and others or result in damage to the product or property of others.
This model is controlled by a radio signal subject to interference from many sources outside
your control. This interference can cause momentary loss of control, so it is advisable to
always keep a safe distance in all directions around your model as this margin will help avoid
collisions or injury.
• Never operate your model with low transmitter batteries.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment
(chargers, rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Never lick or place any portion of the model in your mouth as it could cause serious injury
or even death.
• Exercise caution when using tools and sharp instruments.
• Take care during maintenance as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment such as the motor,
electronic speed control and battery, because they generate high temperatures. You may
burn yourself seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts, as this may cause
damage or serious injury.
• Always turn on your transmitter before you turn on the receiver in the car. Always turn off
the receiver before turning your transmitter off.
• Keep the wheels of the model off the ground when checking the operation of the radio
equipment.
SAFETY PRECAUTIONS AND WARNINGS
EN
2SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

3
EN
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
BOX CONTENTS
QUICK START
Please read the entire manual to gain a full understanding of the Baja Rey vehicle, fine-tuning the setup and performing maintenance.
1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included charging warnings
and instructions for battery charging information.
3. Install the AA batteries in the transmitter. Only use alkaline
or rechargeable batteries.
4. Install the fully charged battery in the vehicle.
5. Power ON the transmitter and then the vehicle.Wait 5 seconds for the ESC to
initialize. Always power the transmitter ON before the vehicle and power it OFF
after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos
are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.
• Losi®Super Baja Rey®RTR with AVC®Technology: 1/6-Scale 4WD Desert Truck (LOS05018)
• Spektrum™ 6-Channel DSMR®AVC2 Surface Receiver (SPMSRS6000)
• Spektrum™18KG Waterproof 1/5-Scale Servo (SPMS904)
• Dynamite®Fuze™ 160A BL WP 1/5-Scale ESC: 8S (DYNS2661)
• Dynamite®Fuze™ Brushless Motor 1200Kv (DYNS1660)
TABLE OF CONTENTS
SAFETY PRECAUTIONS AND WARNINGS................................................................2
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS.........................2
QUICK START.............................................................................................................3
CHARGING THE BATTERY.........................................................................................3
BOX CONTENTS.........................................................................................................3
SRS6000 AVC®TECHNOLOGY RECEIVER................................................................4
SRS6000 STABILITY ASSIST RECEIVER....................................................................4
DISABLING AVC®TECHNOLOGY..............................................................................4
BINDING/CALIBRATING THE RECEIVER ..................................................................4
INSTALLING THE BATTERY........................................................................................5
DRIVING PRECAUTIONS...........................................................................................5
BEFORE RUNNING YOUR VEHICLE ..........................................................................5
POWERING ON THE VEHICLE...................................................................................5
PERFORMING A CONTROL DIRECTION TEST..........................................................6
RUN TIME...................................................................................................................6
POWERING OFF THE VEHICLE..................................................................................6
DYNAMITE FUZE 1200KV BRUSHLESS MOTOR......................................................6
ESC FUNCTIONS........................................................................................................7
TROUBLESHOOTING GUIDE .....................................................................................8
LIMITED WARRANTY ................................................................................................8
WARRANTY AND SERVICE CONTACT INFORMATION ............................................9
FCC INFORMATION..............................................................................................9
IC INFORMATION.................................................................................................9
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION..................................9
REPLACEMENT PARTS ......................................................................................33–34
OPTIONAL PARTS....................................................................................................35
EXPLODED VIEWS.............................................................................................35–39
EN
Choose batteries designed to work with the Dynamite®Fuze™ 160A Brushless Waterproof
ESC. We recommend standard LiPo batteries: the Dynamite®7.4V 5000mAh 2S 50C LiPo:
Hardcase with EC5™ connector (DYNB3810EC) or the Dynamite®11.1V 5000mAh 3S 50C
LiPo: Hardcase with EC5™ connector (DYNB3811EC) -or- HV LiPo batteries: the Dynamite®
7.6V 5000mAh 2S 50C LiPo: Hardcase with EC5™ connector (DYNB3855EC) or the
Dynamite®11.4V 5000mAh 3S 50C LiPo: Hardcase with EC5™ connector (DYNB3856EC).
Choose a charger designed to charge Li-Po batteries. We recommend the Dynamite®
Passport Duo 400W Dual AC/DC Touch Charger (DYNC3005) or the Dynamite®Passport
Ultra 100W AC/DC Touch Charger (DYNC3000). Refer to your battery and charger manuals
for usage, safety, and charging information.
CHARGING THE BATTERY
REGISTER YOUR LOSI PRODUCT ONLINE
Register your vehicle now and be the first to find out about the latest option parts, product
updates and more. Click on the Support tab at www.losi.com and follow the product
registration link to stay connected.
3
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

EN
4SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
EN
SRS6000 AVC®TECHNOLOGY RECEIVER
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power supply for a
personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational. The
remaining Aux channels can be used to power a personal transponder or lights.
If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION), all 6 channels
(including the Aux channels can operate as servo channels).
Antenna
Bind/Battery
Aux 4/Disable
Aux 3
Aux 2
Aux 1
Throttle
Steering
ACTIVE VEHICLE CONTROL™ (AVC®)
The Spektrum receiver features Active Vehicle Control™(AVC®) technology that responds
similar to traction control in full-scale vehicles. In addition to traction control,AVC technology
also increases steering stability during high speed driving or while driving over rough terrain.
As you increase the AVC sensitivity, the system increases steering stability and traction control,
similar to reducing the amount of steering rate in a computer transmitter. Reducing the
sensitivity value increases the amount of steering control from the transmitter. The receiver
also enables you to quickly turn AVC on or off if you participate in organized racing.
IMPORTANT: You must use digital servos with the AVC receiver. Do not use analog servos as
they willl reduce the performance of the system and may cause overheating.
AVC®SENSITIVITY
The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the
sensitivity, the AVC®system becomes more sensitive to the vehicle drifting left or right.You
would use maximum sensitivity during high speed driving or drag racing, when you want
the vehicle to stay in a straight line. As the sensitivity value increases, the amount of steering
travel decreases.
Turn the AVC/ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the AVC/ST RATE knob clockwise to increase the sensitivity
IMPORTANT: The ST RATE knob will only adjust the sensitivity when the transmitter is
bound to a DSMR®AVC® receiver. When the transmitter is bound to a DSM2®/DSMR non AVC
receiver, the ST RATE knob controls the steering dual rate.
BINDING
Binding is the process of programming the receiver to recognize the GUID (Globally Unique
Identifier) code of a single specific transmitter. When areceiver is bound to atransmitter/
model memory, the receiver will only respond to that specific transmitter/model memory.
Your Spektrum DX2E transmitter comes prebound to the vehicle. If you need to
rebind or calibrate, follow the instructions below.
1. With the vehicle on a flat, level surface, insert the Bind Plug in the BIND port on the receiver.
2. Connect a fully charged battery pack to the ESC.
3. Power on the ESC.The orange LED flashes on the receiver, indicating it is in bind mode.
4. Center the ST TRIM and TH TRIM dials on the transmitter.
5. Press and hold the BIND button while powering on the transmitter.
6. Release the BIND button when the orange LED slowly flashes. The transmitter and receiver
are linked when the orange LED is solid.
CALIBRATING (continue from step 6 above)
7. Pull the transmitter trigger to Full Throttle, the orange LED will flash once.
8. Push the transmitter trigger to Full Brake, then return the trigger to center.
9. Turn the transmitter steering wheel to Full Right. The orange LED flashes.
10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.
The orange LED flashes once.
11. Remove the Bind Plug, then power off the receiver to save the settings.
12. Power off the transmitter.
SRS6000 STABILITY ASSIST RECEIVER
If you participate in organized racing, you may be required to turn AVC off. To turn AVC off:
1. Insert a Bind Plug in the BIND port on the receiver.
2. Insert a second Bing Plug in the DISABLE port on the receiver.
3. Connect a fully charged battery pack to the ESC.
4. Power on the ESC.The orange LED flashes, indicating the receiver is in bind mode.
5. Center the ST TRIM and TH TRIM dials on the transmitter.
6. Press and hold the BIND button while powering on the transmitter.
7. Release the BIND button when the orange LED slowly flashes.
The transmitter and receiver are linked when the orange LED is solid.
8. Pull the transmitter trigger to Full Throttle.
9. Push the transmitter trigger to Full Brake, then return the trigger to center.
10. Turn the transmitter steering wheel to Full Right.
11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.
The orange LED flashes once.
12. Remove the Bind Plugs, then power off the receiver to save the settings.
The receiver will continuously blink to indicate AVC is disabled.
13. Power off the transmitter.
IMPORTANT: You must calibrate the receiver each time it is placed in bind mode.
To activate AVC, see the steps in "Calibrating the Receiver."
DISABLING AVC®TECHNOLOGY
BINDING/CALIBRATING THE RECEIVER
4SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

5
EN
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
INSTALLING THE BATTERIES
1. Ensure the ESC is powered OFF.
2. Slide the button to the right to release the battery door.
3. Install the fully charged batteries in the vehicle.
4. Connect the batteries to the ESC.
5. Close the battery door and slide the battery door button to the left to secure it.
6. Power ON the transmitter, then the vehicle.
POWERING ON THE VEHICLE
1. Center the ST TRIM and TH TRIM dials on the transmitter.
2. Power on the transmitter.
3. Connect the fully charged battery packs to the ESC.
4. Power on the ESC.
IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless for
at least 5 seconds.
DRIVING PRECAUTIONS
• Maintain sight of the vehicle at all times.
• Routinely inspect the vehicle for loose wheel hardware.
• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle
off-road can cause fasteners to loosen over time.
• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when
the battery is discharged can cause the receiver to power off. If the receiver loses power,
you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is
not covered under warranty.
CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries dis-
charged to a voltage lower than the lowest approved voltage may become dam-
aged, resulting in loss of performance and potential fire when batteries are charged.
• Do not apply forward or reverse throttle if the vehicle is stuck.
Applying throttle in this instance can damage the motor or ESC.
• After driving the vehicle, allow the electronics to cool before driving the vehicle again.
IMPORTANT: Keep wires away from all moving parts.
BEFORE RUNNING YOUR VEHICLE
1. Check for free suspension movement. All suspension arms and steering components
should move freely. Any binds will cause the vehicle to handle poorly.
2. Charge a battery pack. Always charge the battery pack as per the battery and/or
charger manufacturers’ instructions.
3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim
so that the vehicle drives straight with no input to the steering.
4. Perform a Control Direction Test.
5
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

EN
6SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
PERFORMING A CONTROL DIRECTION TEST
Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the
vehicle is powered ON, adjust the TH Trim knob until they stop.To make the wheels move
forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.
When moving forward, the wheels should maintain a straight line without any steering wheel
input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to
turn the steering wheel.
RUN TIME
The largest factor in run time is the capacity of the battery pack. A larger mAh rating
increases the amount of run time experienced.
The condition of a battery pack is also an important factor in both run time and speed.
The battery connectors may become hot during driving. Batteries will lose performance
and capacity over time.
Driving the vehicle from a stop to full speed repeatedly will damage the batteries
and electronics over time. Sudden acceleration will also lead to shorter run times.
TO IMPROVE RUN TIMES
• Keep your vehicle clean and well maintained.
• Allow more airflow to the ESC and motor.
• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature
of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.
• Use a battery pack with a higher mAh rating.
• Use the optimum charger to charge battery packs (Visit your local hobby dealer for
more information).
PRECAUTIONS
• Never touch moving parts.
• Never disassemble while the batteries are installed.
• Always let parts cool before touching.
GEARING
The vehicle is equipped with the optimal gearing for the stock platform. It offers an ideal bal-
ance between speed, power and efficiency. Should you decide to customize your vehicle with
optional batteries or motors, it may be necessary for you to change the pinion or spur gear.
Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater
torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with
fewer teeth will reduce torque and increase top speed. Care should be taken when installing
larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor
and ESC. When testing different gearing options, pay close attention to the temperature of
the motor and speed control to ensure you are operating within the temperature range of the
components. The motor or ESC should never be so hot that it cannot be touched. If tempera-
tures are too hot, a different gearing combination with a lower pinion gear and/or higher spur
gear is suggested.
CHANGING THE PINION GEAR/GEAR RATIO
The Super Baja Rey uses a motor mount with pre-set gearing from 16-24T.
1. Remove the lower motor mount chassis plate, the motor, and motor mount.
2. Loosen the set screw and remove the installed pinion gear.
3. Install the motor screws corresponding to the number of teeth on the pinion gear.
4. Place the new pinion gear on the end of the motor shaft, so the setscrew is located over
the flat of the shaft.
5. Position the pinion gear so that the teeth line up with the spur gear and secure the pinion
gear by tightening the set screw.
6. Check the gear mesh to ensure that everything spins properly.
DYNAMITE®FUZE™ 1200KV BRUSHLESS MOTOR
SETTING THE GEAR MESH
The motor gearing is set on the motor mount and uses corresponding holes that match the
number of teeth on the pinion gear. The gear mesh has already been set at the factory. Setting
it is only necessary when changing motors or gears.
Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When
the gear mesh is too loose, the pinion gear can damage the spur gear. If the mesh is too tight,
speed could be limited and the motor and ESC will overheat.
IMPORTANT: The included 19T pinion gear is suitable for use with a 6S Li-Po battery.
NOTICE: For extreme load surfaces (e.g., sand and tall grass), gear down 1–2 teeth
on the pinion gear to minimize the chance of motor and ESC damage.
POWERING OFF THE VEHICLE
1. Power off the ESC.
2. Power off the transmitter.
3. Remove and charge the batteries.
6SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

7
EN
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
SPECIFICATIONS
Type Sensorless
Constant/Peak 160A/1050A
Resistance 0.0002Ohm
Function Forward with Brake, Forward/Reverse with Brake
Operation Proportional forward, proportional reverse with braking
Input Voltage 3–8s LiPo
BEC Output 6V/8.4V, 6A
Overload Protection
Motor Lock-up protection, Low-voltage cutoff protection,
Thermal protection, Overload protection and fail safe (throttle
signal loss protection)
Dimensions (LxWxH) 70mm x 65mm x 45.5mm
Weight 288g
ESC LED STATUS
• No ESC LEDs will glow when there is no throttle input from the transmitter.
• The red ESC LED glows when there is any throttle input from the transmitter.
AUDIBLE WARNING TONES
1. Input Voltage: The ESC checks the input voltage when it is powered ON. If a voltage
problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause
(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that
the battery power is not too low for safe operation.
2. Radio Connection: The ESC checks radio signal input when it is powered ON.
If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause
(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.
ESC FUNCTIONS
ESC CALIBRATION PROCEDURE
Ensure proper ESC function by calibrating the ESC to your transmitter inputs.
1. Power OFF the ESC.
2. Ensure your transmitter is powered ON, the throttle is not reversed, the
throttle trim is neutral and the throttle travel range is at 100%. Disable
any special functions such as ABS, etc.
3. Press the SET button while powering ON the ESC. Release the button as soon as the red
LED starts to flash.
4. Calibrate the throttle points by pressing the SET button once after each step.
- Neutral (1 flash)—leave the throttle at rest, untouched
- Full throttle (2 flashes)—pull the throttle fully back
- Full brake/reverse (3 flashes)—push the throttle fully forward
5. The motor will run 3 seconds after the last step is completed.
Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside
motor wires. The center wire must remain in the center and cannot be moved to another
motor tab.
ESC PROGRAMMING PROCEDURE
1. Connect a fully charged battery to the ESC.
2. Power ON the ESC using the ESC switch.
3. Hold the SET button for 1 second until the GREEN LED blinks, then release the SET button
to enter programming mode.
4. Press and release the SET button as needed to get to the desired menu option (the GREEN
LED will blink corresponding to the menu item number). Programming menu items 1
through 6 are accessible using the SET button on the ESC.
5. When at the desired menu item, hold the SET button for 3 seconds until the RED LED blinks.
6. Press the SET button to move among the settings based on how many times the RED LED
blinks (Refer to the table for more information).
7. Save the setting by holding the SET button for 3 seconds.
8. Power OFF the ESC switch and repeat the instructions above to change other settings.
DESCRIPTIONS
1. Running Mode
-Forward Only with Brake
Intended for competition use, this mode allows only forward and brake controls.
-Forward/Reverse with Brake
This mode is the basic all-around mode, allowing forward, reverse and brake controls.
To engage reverse while moving forward, apply the brake until the vehicle has come to
a complete stop, release brake, then apply the brake again. While braking or in reverse,
engaging the throttle will result in the vehicle immediately accelerating forward.
2. Li-Po Cells
The default setting is Auto Calc, which will automatically select the detetected number
of cells. Select value 2–5 to manually select a cell count from 3–8 cells.
3. Low Voltage Cutoff
This function helps to prevent battery over-discharge. The ESC continuously monitors the
battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output
power shuts off and the red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,
if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery
pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a
8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po
battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).
4. Bec Voltage
Select either 6 or 8.4 V to run the receiver and servos.
5. Max Brake Force
Adjusts the maximum braking force. A higher value provides stronger braking, but can
also cause the wheels to lock, resulting in loss of control of the car.
6. Max Reverse Force
This parameter adjusts the maximum power when travelling in reverse.
7. Start Mode (Punch)
Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial
acceleration and level 5 gives a stronger initial acceleration.
8. Timing
Allows for timing value selection according to your motor. Generally, higher timing value
brings out higher power output, but the efficiency of the system will be slightly lower with
possible increases in motor and ESC running temperatures.
The black-shaded setting is the factory default.
PROGRAMMABLE ITEMS
PROGRAMMABLE VALUE
1 2 3 4 5 6 7 8 9
1 Running Mode Forward with Brake Forward/ Reverse with Brake
2 Li-Po Cells Auto Calc. 3s 4s 6s 8s
3 Low Voltage Cutoff Auto (Low) Auto (Intermediate) Auto (High)
4 BEC Voltage 6.0V 8.4V
5 Max Brake Force 25% 50% 75% 100% Disable
6 Max Reverse Force 25% 50%
7 Start Mode/Punch Level 1 Level 2 Level 3 Level 4 Level 5
8 Timing 0° 3.75° 7.5° 11.25° 15°
7
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

EN
8SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE SOLUTION
Vehicle does not operate
Battery not charged or plugged in Charge battery/plug in
ESC switch not “On” Turn on ESC switch
Transmitter not “On” or low battery Turn on/replace batteries
Motor runs but wheels
do not rotate
Pinion not meshing with spur gear Adjust pinion/spur mesh
Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft flat spot
Transmission gears stripped Replace transmission gears
Drive pin broken Check and replace drive pin
Steering does not work Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity
Servo gears or motor damaged Replace or repair servo
Will not turn one direction Servo gears damaged Replace or repair servo
Motor does not run
Motor wires not connected properly Check bullet connectors for proper fit
Motor wire broken Repair or replace as needed
ESC damaged Contact Horizon Hobby Product Support
ESC gets hot Motor over-geared Use smaller pinion or larger spur gear
Driveline bound up Check wheels and transmission for binding
Poor run time and/or sluggish
acceleration
Battery pack not fully charged Recharge battery
Charger not allowing full charge Try another charger
Driveline bound up Check wheels, transmission for binding
Poor range and/or glitching
Transmitter batteries low Check and replace
Vehicle battery low Recharge battery
Loose plugs or wires Check all wire connections and plugs
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the
“Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due
to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,
installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable
technical regulations or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY
OR REPRESENTATION,AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon
will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be
defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,TORT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability
of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon
has no control over use, setup, final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,
the user accepts all resulting liability. If you as the purchaser or user are not prepared to
accept the liability associated with the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law principals). This
warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service.
Once assembly, setup or use of the Product has been started, you must contact your local
distributor or Horizon directly. This will enable Horizon to better answer your questions and
service you in the event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll
free telephone number referenced in the Warranty and Service Contact Information section to
speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live
and use the Product in, please use the Horizon Online Service Request submission process
found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please note that original boxes
may be included, but are not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,
as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.
An Online Service Request is available at http://www.horizonhobby.com/content/_service-
center_render-service-center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting your product
for service. When calling Horizon, you will be asked to provide your complete name, street
address, email address and phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA number, a list of the included
items, and a brief summary of the problem.A copy of your original sales receipt must be
included for warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a
Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt verifying
the proof-of-purchase date. Provided warranty conditions have been met, your Product
will be serviced or replaced free of charge. Service or replacement decisions are at the sole
discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase cost. By submitting the item for
service you are agreeing to payment of the service without notification. Service estimates are
available upon request.You must include this request with your item submitted for service.
Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you
will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for
service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/_service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of
use and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of
the un-serviced Product, through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant Product for a period of 60
days from notification, after which it will be discarded.
10/15
8SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

9
EN
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL
Country of Purchase Horizon Hobby Contact Information Address
United States of America
Horizon Service Center
(Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/
2904 Research Road
Champaign, Illinois 61822 USA
Horizon Product Support
(Product Technical Assistance)
[e-mail]
877-504-0233
Sales [e-mail]
800-338-4639
EU Horizon Technischer Service [e-mail]
[phone]
Hanskampring 9
D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH
Warranty and Service Contact Information
EU Compliance Statement: Horizon Hobby, LLC hereby declares that this
product is in compliance with the essential requirements and other relevant
provisions of the RED and EMC Directives.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users in the
European Union
This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a
designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the
time of disposal will help to conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more information about where you can drop
off your waste equipment for recycling, please contact your local city office, your household waste
disposal service or where you purchased the product.
FCC Statement
FCC ID: BRWDASRX12 This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This product contains a radio transmitter with wireless technology which has been tested and
found to be compliant with the applicable regulations governing a radio transmitter in the
2.400GHz to 2.4835GHz frequency range.
Supplier’s Declaration of Conformity
LOS Super Baja Rey BND
LOS05018
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
CAUTION: changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Horizon Hobby, LLC
4105 Fieldstone Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com
IC Information
IC: CAN ICES-3 (B)/NMB-3(B) | 6157A-AMRX12 This device complies with Industry
Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
9
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

33
IT
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC • MANUALE DI ISTRUZIONI
Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi
Part # English Deutsch Français Italiano
DYNS1660 Fuze 1/6th BL Motor 1200kv Fuze 1/6th BL Motor 1200kv Moteur Fuze 1200kV BL 4P 1/6 Motore Fuze 1/6 denti BL 1200Kv
DYNS2661 Fuze 160A BL WP 1/5th ESC Zünder 160A BL WP 1/5-Maßstab ESC ESC Fuze 160A BL WP 1/5 ESC Fuze 160A BL WP 1/5 denti
LOS235007 Button Head Screw M3 x 12 mm (10) Rundkopfschraube, M3 x 12 mm (10) Vis à tête bombée, M3 x 12mm (10) Vite a testa tonda M3 x 12 mm (10)
LOS235009 Flat Head Screw M2.5 x 8 mm (10) Flachkopfschraube M2,5 x 8 mm (10) Vis à tête plate, M2.5 x 8mm (10) Vite a testa piana M2.5 x 8 mm (10)
LOS235012 Set Screw M4 x 4 mm Cup Point (10) Stellschraube, M4 x 4mm Ringschneide (10) Vis de fixation, bout civette, M4 x 4mm (10) Vite di fermo M4 x 4 mm punta a tazza (10)
LOS235025 Button Head Screw M3 x 30 mm (10) Rundkopfschraube, M3 x 30 mm (10) Vis à tête bombée, M3 x 30 mm (10) Vite a testa tonda M3 x 30 mm (10)
LOS236001 3.2 mm x 7 mm x .5 mm Washer (10) 3,2 mm x 7mm x 0,5 mm Unterlegscheibe (10) Rondelle 3,2mm x 7mm x 5mm (10) Rondella 3,2 mm x 7 mm x 0,5 mm (10)
LOS250022 Body Button Base and Top (22) Body Button unten und oben (22) Bouton corps haut et bas (22) Base e parte superiore bottone carrozzeria (22)
LOS250023 Interior Set w/ Helmets, Clear Interieurset mit Helmen,Transparent Lot intérieur avec casques, clair Serie interni con caschi, trasparente
LOS250024 Brake and Spare Tire Accessory Set Bremse und Ersatzreifen Zubehörset Ensemble d’accessoires pour pneus de secours et freins Serie accessori freno e pneumatico di riserva
LOS250032 Cab Section, Black/White/Orange Baldachinabschnitt, Black/White/Orange Section cabine, Black/White/Orange Sezione abitacolo, Black/White/Orange
LOS250033 Front Hood, Black/White/Orange Frontklappe, Schwarz/ Weiß/Orange Capot avant, Schwarz/ Weiß/Orange Cofano anteriore, Schwarz/ Weiß/Orange
LOS250034 L/R Rear Fender Set,
Black/White/Orange
L/R Heck Schutzblechset,
Schwarz/ Weiß/Orange
Lot de protections arrières D/G,
noir/ blanc/orange
Serie parafanghi anteriori sinistro/destro,
neri/ bianca/ arancia
LOS251054 Roll Cage Sides (L&R) Überrollkäfigseiten (L&R) Cage de retournement, côtés, D/G Lati scocca di protezione (Sinistro e destro)
LOS251055 Rear Body Mount Bar (L&R) X-Bar Hintere Gehäusehalterungsstange (L&R) X-Balken Crossbar, barre de montage (G/D), corps arrière Barra supporto carrozzeria posteriore (Sinistra e destra),
Barra Trasversale
LOS251056 Rear Bulkhead, Fan Panel, Mud Guards Hintere Spritzwand, Lüfterplatte, Schmutzfänger Cloison arrière, panneau ventilation, garde-boue Paratia posteriore, pannello ventola, parafanghi
LOS251057 Front Bumper & Skid Plate Frontstoßstange und Gleitbrett Pare-choc avant et plaque de protection Paraurti anteriore e piastra protezione
LOS251058 Battery Tray, Door, Lock, EC5 Base Set Akkuhalterung,Tür, Schloss, EC5-Basis-Set Support de batterie, porte, verrou, ensemble de base EC5 Vassoio portabatterie, sportello, blocco, serie base EC5
LOS251059 Steering Servo Mount & Bellcrank Set Lenkservo-Halterung & Umlenkhebelset Support de servo de direction et ensemble levier Supporto servocomandi sterzo e serie leve a gomito
LOS251060 Rear Chassis Brace/ESC Mount Hintere Karosseriestrebe/
Geschwindigkeitsreglerhalterung Renfort châssis arrière/support variateur ESC Sostegno anteriore telaio/Supporto ESC
LOS251061 Chassis & Motor Cover Plate Karosserie & Motorabdeckplatte Plaque de couvercle châssis et moteur Piastra copertura telaio e motore
LOS251062 Center Chassis Brace & Stand Offs Zentrale Karosseriestrebe & Standoffs Renfort châssis central et douilles Sostegno e supporti centrali telaio
LOS251063 LED Light Bar Front LED-Lichtstange Front Barre d’éclairage à DEL avant Barra anteriore luci LED
LOS251064 LED Light Bar Rear LED-Lichtstange Heck Barre d’éclairage à DEL arrière Barra posteriore luci LED
LOS251065 Steering Hardware Set Hardwaresatz Lenkung Ensemble de matériel de direction Set bulloneria sterzo
LOS251066 Steering Servo Arm, 15T Spline Servolenkarm, 15T Verzahnung Bras du servo de direction, cannelure 15T Braccio servocomandi sterzo, scanalatura 15 denti
LOS251067 Steering Tie Rods (2) Lenkung Zuganker (2) Biellettes de direction (2) Tiranti sterzo (2)
LOS251068 Foam Seal & Spacer Set Schaumdichtung & Distanzstückset Lot mousse d’étanchéité et entretoises Serie sigillanti in materiale espanso e spessori
LOS251069 Roll Cage Top Bar, Front Bar Obere Stange des Überrollkäfigs, Vorderstange Cage de retournement, barre supérieure, barre avant Barra superiore, barra anteriore scocca di protezione
LOS252039 Pinion Gear,16T, Mod 1.5 Zahnradgetriebe, 16T, Mod 1,5 Engrenage à pignons, 16R, 1,5M Ingranaggio pignone, 16 denti, mod. 1,5
LOS252040 Pinion Gear 17T, Mod 1.5 Zahnradgetriebe, 17T, Mod 1,5 Engrenage à pignons, 17T, 1,5M Ingranaggio pignone, 17 denti, mod. 1,5
LOS252041 Pinion Gear, 18T, Mod 1.5 Zahnradgetriebe, 18T, Mod 1,5 Engrenage à pignons, 18T, 1,5M Ingranaggio pignone, 18 denti, mod. 1,5
LOS252043 Pinion Gear, 20T, Mod 1.5 Zahnradgetriebe, 20T, Mod 1,5 Engrenage à pignons, 20T, 1,5M Ingranaggio pignone, 20 denti, mod. 1,5
LOS252044 Pinion Gear, 21T, Mod 1.5 Zahnradgetriebe, 21T, Mod 1,5 Engrenage à pignons, 21T, 1,5M Ingranaggio pignone, 21 denti, mod. 1,5
LOS252045 Pinion Gear, 22T, Mod 1.5 Zahnradgetriebe, 22T, Mod 1,5 Engrenage à pignons, 22T, 1,5M Ingranaggio pignone, 22 denti, mod. 1,5
LOS252069 Diff Housing & Gasket Differentialgetriebe-Gehäuse & Dichtung Boîtier différentiel et joint Alloggiamento e guarnizione differenziale
LOS252070 Differential Rebuild Kit Differentialgetriebe-Umbau-Kit Kit de reconstruction du différentiel Kit riparazione differenziale
LOS252071 Axle Housing Set, Rear Achsgehäuse-Set, Heck Lot de carte d’essieu, arrière Serie alloggiamento dell’assale, posteriore
LOS252072 Rear Driveshaft Set Heck Antriebswelle-Set Lot d’arbre d’entraînement arrière Serie posteriore albero di trasmissione
LOS252073 Center Transmission Housing Zentrales Getriebegehäuse Boîtier de transmission centrale Alloggiamento centrale trasmissione
LOS252074 Front Gear Box/Bulkhead Front Getriebekasten/Spritzwand Réducteur avant/Cloison Scatola del cambio anteriore/Paratia
LOS252075 38T Ring & 12T Pinion Gear FR/RR 38T Ring & 12T Zahnradgetriebe FR/RR Bague 38T et engrenage à pignons 12T AV/AR Anello 38 denti e ingranaggio pignone 12 denti FR/RR
LOS252076 Outdrive Set FR/RR (2) Antrieb-Set FR/RR (2) Ensemble sortieAV/AR (2) Serie gruppo di trasmissione FR/RR (2)
LOS252077 20 mm Wheel Hexes and Pins, Black (4) 20 mm Rad Sechskante und Bolzen, Schwarz (4) Hexagones de roue et broches 20mm, noir (4) Dadi esagonali e perni ruota 20 mm, neri (4)
LOS252078 Wheel Nut, Black (4) Radmutter, Schwarz (4) Écrou de roue, noir (4) Dado ruota, nero (4)
LOS252079 Pinion Gear, 19T, 1.5M, 8mm Shaft Zahnradgetriebe, 19T, 1,5M, 8mm Welle Engrenage à pignons, arbre de 19T, 1,5M, 8mm Pignone, 19 denti, 1,5M, albero da 8mm
LOS252080 Center Transmission Gear Set Zentrales Übersetzungsgetriebe-Set Lot de transmission centrale Serie centrale ingranaggi trasmissione
LOS252081 Stub Axle, Rear (2) Achswellenstumpf, Heck (2) Porte-fusée, arrière (2) Fusello di ruota, posteriore (2)
LOS252082 Dogbone, Rear Axle (2) Dogbones, Hinterachse (2) Cardans à boules goupillées, essieu arrière (2) Cardano spinato (dogbone), assale posteriore (2)
LOS252083 Motor Mount Motorhalterung Support moteur Supporto motore
LOS252084 Center Drive Shaft, Front Zentrales Antriebswelle, Front Arbre d’entraînement central, avant Albero di trasmissione centrale, anteriore
LOS252085 Front Axle Set (2) Vorderachsenset (2) Lot d’essieu avant (2) Serie assali anteriori (2)
LOS252086 Diff Locker Differentialgetriebefach Verrouillage différentiel Dispositivo di blocco del differenziale
LOS252087 Center Diff Outdrive Set (2) Zentrales Differentialantrieb-Set (2) Lot de sortie de différentiel centrale (2) Serie gruppo di trasmissione centrale (2)
LOS254033 Shock Rebuild Kit (4) Stoßdämpfer-Umbau-Kit (4) Kit de reconstruction amortisseurs (4) Kit riparazione ammortizzatore (4)
LOS254034 Shock & Rod Ends, Spring Cups (12) Stoßdämpfer- und Gelenkköpfe, Federteller (12) Amortisseur et embouts de bielle, cuvettes de ressort (12) Ammortizzatore ed estremità aste, coppe a molla (12)
LOS254035 Shock Pistons Stoßdämpferkolben Pistons amortisseurs Pistoni ammortizzatori
LOS254036 Trailing Arms (2) Hinterachsträger (2) Bras oscillants (2) Bracci longitudinali (2)
LOS254037 Front Suspension Arm Set Upper/Lower (L&R) Front Querlenker-Set Oberer/Unterer (L&R) Bras de suspension avant configuration élevée/basse (G/D) Serie braccetti sospensione anteriore Superiore/Inferiore
(sinistro e destro)
LOS254038 Front Spindle Set (L&R) Front Spindelsatz (L&R) Lot de fusées avant (G/D) Serie fuso anteriore (L&R)
LOS254039 Upper Arm/Shock Mount, Front Oberer Arm/Stoßdämpferhalterung, Front Bras supérieur/support amortisseurs, avant Braccetto superiore/supporto ammortizzatore, anteriore
33
SUPER BAJA REY®DESERT TRUCK: 1:6 4WD BND, AVC