Techni Mobili IDA-8412L User manual

Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the
unit has been completely assembled.
ASSEMBLY INSTRUCTIONS
MODEL IDA-8412L
ASSEMBLY INSTRUCTIONS

L
P
S2
T2
WUT4T3
S3 S4 T1
S1R
Q
M N O
JI K
AC DB
F GE H

▪ ▪ ▪Left Exterior panel ▪ Left Interior panel
▪ Center-Right panel▪ Center-Left panel▪ Right Exterior panel▪ Right Interior panel
▪ Left-Top Shelf panel▪ ▪ ▪ Right-Top Shelf panel
▪ Left Horizontal Back
panel
▪ Top Drawer Left panel
▪Bottom Drawer Left
panel
▪ Right Vertical
Back panel
▪
▪ Bottom Drawer Back
panel
▪ Bottom Drawer Right
panel
▪ Top Drawer Right
panel
▪ Top Drawer Back
panel
▪ Bottom Drawer Front
panel
▪ Top Drawer Front panel
▪ Left Door
▪ Right Horizontal Back
panel
▪ Left-Bottom Shelf
panel
▪ Right-Bottom Shelf
panel ▪ Left Adjustable panel
V
▪ Left Vertical Back
panel

20
14
15
17
16
18
19
1
3
2
4
5
6
7
8
9
10
11
12
13
MAIN PARTS LAYOUT
PART QTY. ITEM
2Pcs Long Wooden Pin
Cam Lock &
Bolt Sets
16Sets
60Pcs Short Wooden Pin
8Pcs Screw - 5 x 8mm
(Euro Screw)
8Pcs Screw TP 10#x1/2''
8Pcs Screw - 3 x 16mm
18Pcs Screw - 3.5 x 16mm
10Pcs Screw - 4 x 38mm
27Pcs Screw - 5 x 40mm
16Pcs Cam lock Covers
19Pcs Screw Covers
4Pcs Metal Pin
Handle U Shape
(96mm)
M3.6x22mm Screw
3Sets
2Sets Sliders
Sets
Right
Left
a
b
a
b
PART QTY. ITEM
Door Hinge Set
(Both parts come
joined together)
2Sets
ab
2Pcs L Bracket
4Pcs Corner Bracket
2Pcs Metal Plate
12Pcs Plactic Feet
1Pc Door Stopper
(For reference):
HARDWARE
EW
L
F
N
J
J
GHQ
C
V
K
D
O
M
I
I
R
P
A
B
T1
S1
S2 S4
S3
U
T3
T4
T2
U

1
Install 60pcs of Wooden Pins (2) into all panels as shown. Use a wooden or light rubber hammer to avoid
damage to the pins. Please pay attention to the correct holes to use as other holes on the panels are
intended for other hardware in other steps. DO NOT JOIN ANY PANELS, JUST INSTALL THE PINS.
2
- Install the wooden pins (1) into panel (A) in the holes shown in the illustration and then install the door
stopper (13) to panel (K) as shown.
2
1
A
K
13
C
DGHE
F
S2
S1
T2
T1
N
L
K
M
I
I
J
J
P
Q

3
4
- Attach L Bracket (16) to the panel (P) and (Q) using screw (7) as shown.
- Install bolts (3) into panels (A), (B), (S1) and (T1) in the holes indicated in the illustration. Please pay
attention to the correct holes to use as other holes on the panels are intended for other , and attach the
metal plates (18) using screws (7) as shown.
7
16
x 16
x 4
x 2
BA
T1
S1
P
Q

5
Separate the 4 pieces of the sliders (20) according to their shape:
- The at shaped will be used in the next step (2 pieces, both left and right).
- The “L” shaped will be used until step 21 (2 pieces, left and right).
6
- Install the at shaped sliders (20) on panels (E) and (F) using screws (4) as shown.
4
Flat Shaped
"L" Shaped
E
F
20
(TOP)
(TOP)
(Front)
(Front)

7
- Assemble the panel (H) to panel (Q) using screw (9) as shown.
8
9
This illustration shows the same
parts from step 7, but viewed
from a different angle (from the
right).
Assemble the panel (E) to panel (Q) using screws (9) as shown.
Q
H
(BOTTOM)
(Front)
(Top)
(Top)
(Front)

9
10
- First assemble the panel (F) to panels (L) and (N) using screws (9), then install the nail-in studs (19) to
the bottom of the panels (E), (F) and (H) as shown.
9
9
This illustration shows the same
parts from step 8, but viewed
from a different angle (from the
left).
L
J
N
J
19
F
19
E
- First assemble the panels (L) and (N) to panel (E) using screws (9), then join panels (J) to panel (E) by
just pushing the pins into the holes.
E
H
L
N
This illustration shows the same
parts from step 9, but viewed
from the right.

11
12
9
9
This illustration shows the same
parts from step 11, but viewed
from a different angle (from the
left).
- Assemble the panel (G) to panel (P) using screw (9) as shown.
- Assemble the panel (D) to panel (P) using screw (9) as shown.
(Top)
(Front)
(Top)

13
14
9
9
19
K
I
M
I
C
-First assemble the panels (K) and (M) to panel (D) using screws (9), then join panels (I) to panel (D) by
just pushing the pins into the holes.
-First assemble the panel (C) to panels (K) and (M) using screws (9), then install the nail-in studs (19) to
the bottom of the panels (C), (D) and (G) as shown.
D
G
This illustration shows the same
parts from step 12, but viewed
from a different angle (from the
right).
K
M
This illustration shows the
same parts from step 13,
but viewed from the left.

15
16
First install and align cam locks (3) into panels (C), (D), (E), (F), (G) and (H). Then place the main
tabletop (A) over the frame on the left side and the right tabletop (B) on the right side. Then proceed to
lock the cam locks as explained in page 4. Finally, cover the cam locks with caps (10).
- First place the parts assembled in steps 10 and 14 in the position shown in the illustration, and assemble
panel (H) to panel (G) using screws (9). Then slide the panel (V) into the groves of (C) and (D), and (W)
into the groves of (E) and (F). Finally, install the metal pins (12) in the desired sets of holes on panels (C)
and (D), and place the panel (O) over the pins as shown.
3
9
12
10
H
G
O
F
W
E
V
C
D
A
B
C
DE
F
This illustration shows the parts
assembled in step 10 and 14 in
normal upright position.
2nd 3rd
1st and 4th
Last

17
18
- First make sure that the back edge of the tabletop (B) align with the edge of the tabletop (A), then using
screws (7), and from underneath the unit, attach:
- The metal plate (18) from (A) to (B).
- The L Brackets (16) from (P) to (A) and from (Q) to (B).
- From behind the unit, and using screws (6), install the corner brackets (17) on the positions shown in the
illustration.
6
17
7
A
B
P
Q
This illustration shows the parts
same parts from step 17, but
viewed from behind.

19
21
-Using cam locks (3), and as shown and
explained in page 4, assemble:
- The side panels (S2) and (S3) to front panel
(S1).
- The side panels (T2) and (T3) to front panel (T1).
Then insert the bottom panels (U) into the groves
of the panels on each drawer as shown.
Assemble the drawers back panels (S4)
and (T4)to their respective drawers using
screws (8) as shown.
22
8
20
3
S2 S3
U
U
T2
T3
Place the drawers upside-down and
assemble the “L” shaped sliders to the bottom
using screws (7) as shown.
Please note that the wheels go towards the
back of the drawers and the sliders should
not protrude from the bottom, otherwise the
drawers raise 3/4” and will not t in the unit.
- Install Handle set (14) to both drawers, Then
attach Covers (10) to both drawer side panels
(S) & (R) as shown above.
7
10 14
7
7
21
20
14
14
10
S1
T1

23
24
14
R
14
R
S
T
- Assemble the door (R) to the desk using
screws (5) as shown and adjust the
alignment if necessary:
(A): These screws adjust the vertical
alignment.
(B): This screws adjusts the horizontal
alignment.
(C): This screws adjusts the depth.
Place both drawers into the cabinet as
shown.
- Install Handle Sets (14) to door (R) , then install Hinges (15) with screw (5) as shown above.
15
5

25
- Cover all the screw heads with caps (11) as shown.
Enjoy your new unit!
DONE! Before you start using the unit, make sure that all the screws, bolts, cam
locks, etc. are properly tightened, and read all the warnings in the next page.
11