Techni Mobili RTA-0054 User manual

Thank you for purchasing our product.
MODEL RTA-0054
ASSEMBLY INSTRUCTIONS

•Please read carefully the assembly instructions
before the installation.
P. 2 RTA-0054 P. 2
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.

MAIN PARTS LIST
A
x1
B
x1
C
x1
D
x1
E
x1
F
x2
G
x2
H
x2
I
x1
J
x1
K1
x1
K2
x1
K3
x1
K4
x1
K5
x1
L1
x1
L2
x1
L3
x1
L4
x1
L5
x1
N
x4
O
x1
M
x2
Main panel Left panel for left
cabinet
Right panel for left
cabinet
Top panels for both
cabinets
Bottom panel for
both cabinets
Left panel for
drawers’ cabinet
Right panel for drawers’
cabinet
Removable panel Left panel for small
drawer
Back panels for both
cabinets
Door panel for left
cabinet
Bottom panel for
small drawer
Front panel for small
drawer
Right panel for small
drawer
Back panel for small
drawer
Back panel for large
drawer
Bottom panel for
large drawer
Left panel for large
drawer
Right panel for large
drawer
Bottom metal supports
for the cabinets
Metal back panel
Front panel for large
drawer
Top metal supports
for the main panel
P
x8
Q
x4
R
X2
sets
S
x3
sets
Set of 1 hinge with 6
screws 15mm
Set of 1 handle with
2 screws 22L
Studs Sliders for drawers
P. 3 RTA-0054 P. 3

PART QTY SIZE / DESCRIPTION / FIGURE
❿832L
⓫440L
⓬452L
⓭412L
⓮14mm Allen wrench
MAIN PARTS LAYOUT (FOR REFERENCE):
SCREWS LIST:
PART QTY SIZE / DESCRIPTION / FIGURE
❶16 Large wooden pins for cabinets
❷22 Cam bolts
❸16 Large cam locks for cabinets
❹12 12mm
❺4Metal pins
❻49L
❼838mm
❽6Small cam locks for the drawers
❾2Small wooden pins
for small drawer
NOTE: You will also need for the assembly a Phillips screwdriver and mallet/hammer (not included).
󰐚
󰐘
󰐜
󰐝
󰐞
󰐛
󰐛
󰐠
󰐟
󰐖
󰐢
󰐡
P. 4 RTA-0054 P. 4
THE FOLLOWING COME IN BAG#1: THE FOLLOWING COME IN BAG#2:

☛This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the assembly using this
kind of hardware.
1. Screw the bolt into the
corresponding panel.
2. In the other panel, insert the
cam lock and align it so it can
properly receive the bolt, then join
both panels (the cam locks might
come pre-installed in this unit).
3. The panels might have a very
small gap which is normal; turn
the cam lock clockwise to lock the
parts together and the gap will
also close.
Cam Bolt Cam Lock
ALIGNMENT
DIRECTION
P. 5 RTA-0054 P. 5

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
P. 6 RTA-0054 P. 6
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged and
defective parts can be
replaced at no cost to you.
Please refer to the last pages
on this manual.
❸The replacement parts service
is limited to the continental United
States. If you reside in Hawaii,
Puerto Rico, U.S. Dependencies
or other countries, please contact
the supplier from where the unit
was purchased.
❹If during assembly you
find an issue or need
clarification, please contact
our Customer Service for
assistance. Please refer to the
last pages on this manual.
❺On each step read the
instructions and analyze the
illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you understand
which hardware will be used
on each step. Using the wrong
size of screw, bolt or pin might
strip the threads or cause
damage to the part in which it
is being used.
❼To avoid misalignments,
always leave the screws
loose and tighten them until
all pieces are positioned
correctly.
❾Sometimes the laminate might cover partially or entirely
the hole on a panel. If there is no visible hole for the screw,
pass and press the tip of your finger over the area where
the hole should be located to feel the indentation, and once
found, carefully pierce the laminate to reveal the hole
underneath.
❿If the hole seems too small for the screw, first make
sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to
be too small, carefully pierce the laminate to reveal the
hole’s actual size.

First insert the small wooden pins ➈into the bottom holes on the front profile of the side
panels and , then assemble the back panel to the side panels using screws ⑦
as shown.
Slide the bottom panel through the grooves of all panels , and .
STEP 2
K1 K2 K3
(Front)
(The small groove is on
the interior surface at the
bottom on all panels)
K4 K1 K2 K3
(Front)
(The large groove is on the
exterior surface in the middle of
the side panels)
First attach the cam bolts ②on the top holes of the interior surface on the front panel ,
then install and align the small cam locks ⑧on the side panels and , and finally
assemble the front panel as shown and as explained in page 5.
K5
K1 K2
K5
(This view shows the drawer from
behind with its front facing right)
Refer to page 5
STEPS 1 THRU 8: DRAWERS ASSEMBLY
P. 7 RTA-0054 P. 7
STEP 1
Hardware/Tools:
➐38mm
4
Pcs
➒Small
2
Pcs
(NOT INCLUDED)
STEP 3
Hardware/Tools:
❷2
Pcs
❽Small
2
Pcs
(NOT INCLUDED)

Assemble one of the handles Ⓢto the front panel using its own screws from the inside
as shown.
K5
Assemble the back panel to the side panels and using screws ⑦as shown.
L3 L2
L1
(The large groove is on the
exterior surface in the middle of
the side panels)
(Front)
(The small groove is on the
interior surface at the bottom
on all panels)
STEP 6 L4 L1 L2 L3
Slide the bottom panel through the grooves of all panels , and .
(Front)
(This view is from the front facing to the
left)
P. 8 RTA-0054 P. 8
(Front)
STEP 5
Hardware/Tools:
❼38mm
4
Pcs
(NOT INCLUDED)
STEP 4
Hardware/Tools:
󰐦1
Set
(NOT INCLUDED)

Assemble the front panel to the side panels and using cam bolts ②and cam
locks ⑧just as in step 3 and as explained in page 5.
L5 L1 L2
Assemble the second handle Ⓢto the front panel using its own screws from the
inside as shown.
L5
STEPS 9 THRU 14: CABINETS ASSEMBLY
Place one of the panels Ⓖupside-down and assemble 2 of the bottom frames Ⓝusing
screws ⑩, then attach the studs Ⓟas shown. Then repeat for the second cabinet base.
Repeat for the second cabinet base:
Refer to page 5
(This view is from
behind with the front
facing to the right)
(Front)
P. 9 RTA-0054 P. 9
STEP 7
Hardware/Tools:
❷4
Pcs
❽Small
4
Pcs
(NOT INCLUDED)
STEP 9
Hardware/Tools:
󰀓8
Pcs
❿8
Pcs
⓮
STEP 8
Hardware/Tools:
󰐦1
Set
(NOT INCLUDED)

With the side panels Ⓓand Ⓔoriented as shown, assemble the sliders Ⓠusing screws
④, making sure the smaller rails attach to the panels, and the larger rails slides in and out.
TIP: Assemble first on the back holes of the sliders
(Front)
(Front)
(The grooves are at the back of the panels)
(The smaller rail gets
attached to the panels; the
larger rail slides in and out)
Please pay attention to which holes to use on the sliders
(Top surface)
Refer to page 5
(Front)
(The grooves are at
the back of all the
panels)
Wooden pins ①on outer holes;
Cam bolts ②on inner holes
(This view is from the
front facing to the right)
First insert the wooden pins ①into the innermost set of holes on the top surface of bottom
panel Ⓖ, then attach the cam bolts ②into the outermost sets of holes; then insert and
align the cam locks ③into the bottom sets of holes on the side panels Ⓓand Ⓔand
finally, assemble the side panels to Ⓖas shown and as explained in page 5.
P. 1 0 RTA-0054 P. 1 0
STEP 10
Hardware/Tools:
❹12
Pcs
(NOT INCLUDED)
STEP 11
Hardware/Tools:
❶4
Pcs
❷4
Pcs
❸4
Pcs
(NOT INCLUDED)

Slide the back panels Ⓗthrough the grooves of panels Ⓑ-Ⓒ-Ⓖand Ⓓ-Ⓔ-Ⓖ
respectively as shown.
STEP 13
(Front)
(Front)
(This view shows the cabinets in their normal and
respective positions, from the front facing to the left)
(Top surface)
Wooden pins ①on outer holes;
Cam bolts ②on inner holes
Refer to page 5
(Front)
(The grooves are at
the back of all the
panels)
Assemble the side panels Ⓑand Ⓒto the second panel Ⓖusing wooden pins ①, cam
bolts ②and cam locks ③just as it was explained in step 11 and in page 5.
P. 11 RTA-0054 P. 11
STEP 12
Hardware/Tools:
❶4
Pcs
❷4
Pcs
❸4
Pcs
(NOT INCLUDED)

Wooden pins ①on inner holes;
Cam bolts ②on outer holes
Assemble the cabinet top panels Ⓕto the side panels Ⓑ-Ⓒand Ⓓ-Ⓔrespectively using
wooden pins ①, cam bolts ②and cam locks ③as shown and as explained in page 5.
Refer to page 5
STEPS 15 THRU 24: REST OF UNIT ASSEMBLY
Assemble the metal back panel Ⓞto the side panels Ⓒand Ⓓusing screws ⑬as shown.
(This view shows the unit from behind)
P. 1 2 RTA-0054 P. 1 2
STEP 15
Hardware/Tools:
⓭4
Pcs
⓮
STEP 14
Hardware/Tools:
❶8
Pcs
❷8
Pcs
❸8
Pcs
(NOT INCLUDED)

Assemble the top metal support frames Ⓜto both cabinet top panels Ⓕusing screws ⑪
as shown.
(This view shows the unit
from the front and from
below facing to the left)
(Front)
(Bottom)
Assemble the last handle Ⓢto the exterior surface of the door panel Ⓘusing its own
screws.
Assemble the hinges Ⓡto the left panel Ⓑusing its own screws, but only on the oval
holes (2 screws per hinge).
(Front)
IMPORTANT: Assemble only on
the 2 back oval holes on the hinges
(This view shows the unit from
the front facing to the left)
P. 1 3 RTA-0054 P. 1 3
STEP 17
Hardware/Tools:
󰐥2
Sets
Note: You will use
only 4 of the 12
screws
(NOT INCLUDED)
STEP 16
Hardware/Tools:
⓫4
Pcs
⓮
STEP 18
Hardware/Tools:
󰐦1
Set
(NOT INCLUDED)

Assemble the door Ⓘto the hinges Ⓡusing hinge screws Ⓡas shown.
Note: there will be still 4 screws Ⓡleft for step 20.
First fine-tune the hinges Ⓡto make the door Ⓘclose smoothly by adjusting the screws
indicated below, then secure using the last screws Ⓡon the 2 other holes on the hinges
as shown.
Adjusts the
depth.
Adjusts the height.
Adjusts side-to-
side.
P. 1 4 RTA-0054 P. 1 4
STEP 19
Hardware/Tools:
󰐥4
Pcs
(NOT INCLUDED)
STEP 20
Hardware/Tools:
󰐥4
Pcs
(NOT INCLUDED)
FINE-TUNE FIRST!
THEN SECURE

First install the metal pins ⑤into the sets of holes on panels Ⓑand Ⓒof the left cabinet,
then insert and place the removable panel Ⓙover the pins.
You might need to insert the panel
at an angle as shown.
P. 1 5 RTA-0054 P. 1 5
STEP 21
Hardware/Tools:
❺4
Pcs

On the right cabinet pull out the bottom sliders Ⓠand assemble the large drawer to the
sliders by fitting them into the grooves on the side panels and , then secure them
with screws ⑥from inside the drawer as shown.
L1 L2
On the right cabinet pull out the top sliders Ⓠand assemble the small drawer to the sliders
by fitting them into the grooves on the side panels and , then secure them with
screws ⑥from inside the drawer as shown.
K1 K2
(This view shows the unit from
The front facing to the right)
STEP 22
Hardware/Tools:
❻2
Pcs
(NOT INCLUDED)
STEP 23
Hardware/Tools:
❻2
Pcs
(NOT INCLUDED)
P. 1 6 RTA-0054 P. 1 6

Place the main panel Ⓐover the top metal supports Ⓜmaking the holes coincide, and
assemble the panel using screws ⑫from underneath the unit as shown.
☛Assembly tip: To avoid misalignments, screw loosely and tighten the screws only after all
are in place.
(This view shows the unit from
The front facing to the left)
(This view shows the unit from behind. The screws go from
underneath through the metal and into the hole on the panel)
P. 1 7 RTA-0054 P. 1 7
STEP 24
Hardware/Tools:
⓬4
Pcs
⓮
ALL DONE!
Give yourself a nice pat on the back. You did a
great job!

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING
CARE AND MAINTENANCE WARNINGS:
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry
with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as underneath the
tabletop.
•Do not seat on the unit or lean against it.
•Do not allow small children to play under or over the unit, or inside the left cabinet.
•Do not allow small children to reach inside the drawers or left cabinet without your supervision.
•Do not drag the unit to move it around, it must be handled by at least 2 persons.
•Before moving the unit, make sure to remove any object that is heavy or might fall off.
•When lifting the unit, use both hands and bend your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts might be
available to you at no charge. Please refer to the WARRANTY card included with the product.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for
damages or consequences due to accidents, incorrect assembly, negligence, improper use,
modifications, or not heeding the above warnings.
•The warranty is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
Dependencies or other countries, please contact the supplier from where the unit was purchased.
WEIGHT LIMITS
88 Lbs. (40 Kg)
44 Lbs. (20 Kg)
22 Lbs. (10 Kg)
22 Lbs. (10 Kg)
44 Lbs. (20 Kg)
33 Lbs. (15 Kg)
33 Lbs. (15 Kg)
P. 1 8 RTA-0054 P. 1 8

P. 1 9 RTA-0054 P. 1 9
RTA Products, LLC warrants to the Original Purchaser who acquired a new product
from RTA Products or its authorized resellers that this product will be free from defects
in its workmanship and materials, under normal use and service conditions, as
described herein. "Defects" as used in this warranty, is defined as any imperfections
that impair the use of the furniture or product. RTA Products LLC will replace any
defective part, at its discretion, and without charge to the original purchaser other than
the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production
may be unavailable. This warranty will be effective for the applicable time period
beginning the date of purchase on your original sales receipt. RTA product’s obligation
under this warranty is limited to repairing or replacing products or parts as provided
herein. This product has been designed for and is intended for office and home-office
use only. This warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by or
attributed to abuse or misuse, products used for commercial or rental purposes, use
modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or
implied, including without limitations any implied warranty or merchantability or of fitness
for a particular purpose. Please note, all desks made with PVC Laminate surface should
not be exposed to direct sunlight, as it may damage the material. Damage of this nature
is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages. This warranty is limited to merchandise purchased in the Continental United
States. Some States do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that may
vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to
explain the defect and give your name, address and phone number. Please have
ready the model number of our product, date and place of purchase. You can also
write to us by e-mail to [e-mail] and include the same
information.
b. b. If we determine that replacement will remedy the situation, and in order to
determine the extent or the cause of the defect, purchaser will need to send the part
in question at purchaser’s expense. Once we receive the part, we will examine it
and determine whether the claim is valid (or not), and then proceed to send the
replacement. We will ship the replacement at our expense.
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
TV Stand/Entertainment Center: 2 YEAR WARRANTY

P. 2 0 RTA-0054 P. 2 0
FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]