Techni Mobili RTA-3528 User manual

Thank you for purchasing our product.
ASSEMBLY INSTRUCTIONS

A
x1 B
x1 C
x1 D
x1
Backrest Seat Base Mechanism
MAIN PARTS LIST
E
x1
F
x5 G-L
x1 H
x1
Gas lift
Casters Left
Armrest Gas lift
Cover
LIST OF HARDWARE
PART
QTY ITEM USE FOR
I4M8x20 Mechanism to seat
J8M6x25 Armrests
K8Covers Armrests
L1Allen Wrench
G-R
x1
Right
Armrest
Sitting on the chair, not looking at it

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS
AND WARNINGS.
❶Do a quick inventory to
make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost to
you. Please refer to the
last page in this manual.
❸The replacement parts
service is limited to the
continental United States. If
you reside in Hawaii,
Puerto Rico, U.S.
Dependencies or other
countries, please contact
the supplier from where the
unit was purchased.
❹If during assembly
you find an issue or
need clarification,
please contact our
Customer Service for
assistance. Please refer
to the last page in this
manual.
❺On each step read
the instructions and
analyze the
illustrations thoroughly
before proceeding to
do the assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which hardware
will be used on each step.
Using the wrong size of
screw, bolt or pin might
strip the threads or cause
damage to the part in which
it is being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾If the hole seems too big or too small for the
screw, first make sure you are using the correct
size of screw and that it’s been installed in the
correct hole. Test another of the same screw
into the same hole, as well as test the screw
onto different holes for the same part. If the
hole still appears to be too small, do not force
it, it needs replacing.

ASSEMBLY STEPS
Insert all the casters Finto
the base Cusing pressure,
then place the gas lift Ein
the middle of the base Cand
cover it with H.
Attach the mechanism D to
the seat B with screws I.
Please note that the knob on
the mechanism will face
towards the front.
(Front)
STEP 2
Hardware
I
8x20mm
4
Pcs
L
STEP 1
F
E
C
H
D
B
STEP 3 Put the seat over the base
parts making sure the tip of the
gas lift Eenters into the hole of
the mechanism D.
D
E
B
(Front)

Assemble the armrests GL and GR to the seat B on their respective
sides using screws J. Screw them loose and do not tighten them to
allow flexibility for step 5.
Assemble the backrest A to the
armrests G with screws J,
and proceed to tighten all the
screws on the armrests.
ALL DONE! Give yourself a nice pat on the back. You did a great job!
LEFT
G-L
RIGHT
G-R
A
B
STEP 6
Hardware
K8
Pcs
G-R
RIGHT
G-L LEFT
STEP 4
Hardware
J
6x25mm
4
Pcs
L
STEP 5
Hardware
J
6x25mm
4
Pcs
L
Cover the screw holes on the
armrests with K as shown.

①To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair
goes down while sitting on it, or up if you lift your body.
②To make the chair tilt freely, pull the same lever OUT horizontally to unlock this
function. When the chair is in the normal upright position, push the lever IN to lock
again.
③To adjust the tension for the tilting function, turn the mechanism’s knob in either
direction to apply more or less tension. With less tension, the tilting will feel easier.
CHAIR’S FUNCTIONS
WARNINGS
• Do not exceed the indicated weight limit.
• Do not stand up on the chair or use it as ladder.
• Use the chair to sit only one person at a time.
• Do not use the chair if parts are damaged or if screws are loose or missing.
• Do not sit near the edge of the seat and always sit properly on the chair to avoid going
beyond your balance point and fall off the chair.
• The chair is intended for teenagers and adults. If small children are using the chair,
please keep close observation on them.
• Do not allow small children to play with the chair.
• Not paying attention to these warnings could result in severe injuries.
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of
smooth soap and water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like
underneath the seat.
•Do not expose the product to direct sunlight or to extreme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are
tighten.
CARE AND MAINTENANCE
Weight
Limit:
220 Lbs
3
2
1

TASK/KID'S CHAIR: 1-YEAR WARRANTY
EXECUTIVE/MANAGER CHAIR: 2-YEAR WARRANTY
We warrant our products to the original purchaser who acquired a new product from us or its
authorized re-sellers of the product against defects in material or workmanship.
This warranty is expressly limited to the repair or replacement (at its option) of defective product
components or materials as a result of a defect in materials or workmanship. This warranty is
limited to merchandise purchased in the Continental United States. No assembly labor isincluded.
The word "defects" as used in this warranty, is defined as imperfections that impair the utility of the
product.
This warranty applies under conditions of normal use, but does not applyto defects that result from
intentional damage, wear &tear, negligence, unreasonable use or exposure.
Liability for consequential damages is excluded to the extent exclusion is permitted by law. This
warranty gives you specific legal rights, and you may have other rights that vary from State to State.
We do not warrant: a) natural variations in character marks b) changes in surface finishes due to
aging or exposure to light c) marks, scars, or wrinkles occurring naturally in leather d) failure
resulting from normal wear and tear e) the matching of colors, grains, or textures of natural
materials f) the colorfastness or the matching of textiles, including an exact match to cuttings or to
swatch cards g) damage, marking, or staining of veneer surfaces due to contact with rubber or
similar compounds, damage from sharp objects or imprinting from writing instruments, or prolonged
exposure to direct sunlight)we do not warrant products that are exposed to extreme environmental
conditions or that have been subject to improper storage.
We shall not be liable for loss of time, inconvenience, commercial loss, or incidental or
consequential damages.
Any modification to the original product voids the warranty. We do not warrant the performance of
the product when used in combination with other than original products.
This product has been designed for and is intended for office, home-office and gaming use only.
This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not
extend to any product, or damage to any product, caused by or attributed to abuse or misuse,
products used for commercial or rental purposes, use modifications of, or attachments to the
product, and products or parts not used, maintained, or extended here under isin lieu of any and all
other warranties, express or implied, including without limitations any implied warranty or merchant
ability or of fitness for a particular purpose.
Report any defects to us together with your sales receipt or other proof of purchase. If the chair is
defective within the terms of the warranty, we will furnish a replacement chair (at its option) at no
cost of equal or similar value and design.
We will advise you of the procedure to follow in making warranty claims.