Furniture of America CM3339-SC-2PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-18
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
CM3339-SC-2PK

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List Hardware List
#1 x 1 pc x 2
Backrest w/Legs
#2 x 1 pc x 2
Seat
#3 x 2 pcs x 2
Front Leg
#A x 9 pcs x 2
Flat Washer
#B x 9 pcs x 2
Lock Washer
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 4 pcs x 2
Bolt 5/16”x3-1/2”
MD
#D x 1 pc x 2
Bolt 5/16”x1-3/4”
Page 4 of 6
#E x 4 pcs x 2
Bolt 5/16”x2-1/4”
#F x 1 pc
Allen Wrench
#G x 2 pcs x 2
Wood Dowel
Note: The above parts and hardware are shown for a complete
assembly of ONE chair. However, the actual parts and hardware (with
an exception of the Allen wrench) in the box will be twice the quantities
listed to include the assembly of the second chair.
X 2

I. Place the backrest with legs (#1)
on a protected surface. Insert
two wood dowels (#G) into the
holes of the backrest with legs
(#1).
II. Align the seat (#2) with the wood
dowels (#G) and the pre-drilled
holes of the backrest with legs
(#1).
III. Prepare a bolt assembly by
inserting FIRST the lock washer
(#B) onto the bolt (#D) and then
the flat washer (#A) onto the
SAME bolt (#D), in that order.
IV. Insert the bolt assembly through
the center hole of the seat (#2)
and secure that bolt using the
Allen wrench (#F) to lock it with
the backrest with legs (#1).
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
Page 5 of 6
#A x 1 pc
#B x 1 pc
#D x 1 pc
#G x 2 pcs
#A x 4 pcs
#B x 4 pcs
#C x 4 pcs
I. Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#B) onto the bolt (#C) and then the flat washer (#A) onto the
SAME bolt (#C), in that order.
II. Insert the bolt assemblies through the pre-drilled holes in the
corners of the seat (#2) and secure those bolts using theAllen
wrench (#F) to lock them with the backrest with legs (#1).

I. Align the two front legs (#3)
with the pre-drilled holes of
the seat (#2).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock
washer (#B) onto the bolt (#E)
and then the flat washer (#A)
onto the SAME bolt (#E), in
that order.
III. Insert the bolt assemblies
through the pre-drilled holes
in the corners of the seat (#2)
and secure those bolts using
the Allen wrench (#F) to lock
them with the legs (#3).
Turn right (clockwise) to tighten
Page 6 of 6
#A x 4 pcs
#B x 4 pcs
#E x 4 pcs
Carefully place the completed chair in upright
position. Make sure the chair is rested on a
flat surface and does not feel loose or wobbly.
If it does, double check that the bolts/screws
are secured and properly tightened.
ASSEMBLE EVERYTHING EXACTLY THE SAME FOR THE SECOND CHAIR