Techni Mobili RTA-7310D User manual

Thank you for purchasing our product.
MODEL RTA-7310D
ASSEMBLY INSTRUCTIONS
REV.PFT-6378-0122-0

•Please read carefully the assembly instructions
before the installation.
•Do not discard this manual or any of the packaging
material until the unit has been completely
assembled.
•Might require two people.
P. 1 RTA-7310D P. 1

P. 2 RTA-7310D P. 2
1
x1 2
x1 3
x1
4
x1
Left frame Middle frame Right frame
Bottom tube
MAIN PARTS LIST
5
x1 6
x1
7
x2 8
x2
Top-front tube Top-back tube
Back support tube (“V”) Top shelf support tube 9
x1
10
x1
Top shelf horizontal tube
Earphones hook 11
x1 12
x2
CPU panel Left shelf panel
13
x1 14
x1
Main panel Top shelf panel

MAIN PARTS LAYOUT (FOR REFERENCE):
P. 3 RTA-7310D P. 3
LIST OF HARDWARE, SCREWS AND FITTINGS
PART
QTY ITEM
A1M6x12
B28 M6x30
C10 M6x45
D16M3.5x12
E2M6x2
PART
QTY ITEM
F2Locking
caster
G2Non-Locking
caster
1Screwdriver
1Wrench
(Spanner)
1Allen
Wrench
1
2
11 3
14
8
8
9
13
6
4
12
12
7
10
5

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
❶Do aquick inventory
to make sure the package
contains all the parts and
hardware listed in the
assembly instructions.
❷Missing, damaged
and defective parts can
be replaced at no cost
to you. Please refer to
the last pages on this
manual.
❹If during assembly
you find an issue or
need clarification, please
contact our Customer
Service for assistance.
Please refer to the last
pages on this manual.
❺On each step read the
instructions and analyze
the illustrations thoroughly
before proceeding to do the
assembly.
❽Do not overtighten
or force the screws as
they might break, strip,
damage the threads of
the holes or get stuck
inside the part.
❻Make sure you
understand which
hardware will be used on
each step.Using the
wrong size of screw, bolt
or pin might strip the
threads or cause damage
to the part in which it is
being used.
❼To avoid
misalignments, always
leave the screws loose
and tighten them until
all pieces are
positioned correctly.
❾Sometimes the laminate might cover
partially or entirely the hole on apanel.If there
is no visible hole for the screw, pass and press
the tip of your finger over the area where the
hole should be located to feel the indentation,
and once found, carefully pierce the laminate to
reveal the hole underneath.
❿If the hole seems too small for the screw,
first make sure you are using the correct size of
screw and that it’s been installed in the correct
hole.If the hole still appears to be too small,
carefully pierce the laminate to reveal the
hole’s actual size.
P. 4 RTA-7310D P. 4
❸The replacement parts
service is limited to the
48 contiguous United States.
If you reside in Alaska,
Hawaii, Puerto Rico,
U.S. territories or other
countries, please contact the
supplier from where the unit
was purchased.

ASSEMBLY STEPS
Assemble the first left shelf 12 to the middle bars on the frames 1and 2
with screws Bfrom underneath.
STEP 1
Hardware:
BM6x30
4
Pcs
P. 5 RTA-7310D P. 5
Assemble the second left shelf 12 to the bottom bars on the frames 1
and 2with screws Bfrom underneath.
1
2
12
(Top)
Make sure to place the frame with
this hole towards the back of the
unit, it is needed for step 3.
STEP 2
Hardware:
BM6x30
4
Pcs
1
2
12
(Top)

P. 6 RTA-7310D P. 6
Bring the cabinet built in step 2 to the upright position, then with the
help of another person:
•Assemble the tubes 4, 5 and 6 to the middle frame 2 in their
respective positions with screws C.
•Assemble the right frame 3to the tubes 4, 5and 6with screws C.
•Attach the hook 10 to the frame 3with screw Afrom the inside.
•Assemble the support tubes 7to the top tube 6on the back of the unit
with screws Cfrom outside and nut caps Efrom inside.
•Assemble the support tubes 7to the bottom tube 4with screws B
from underneath.
Note: If you don’t see holes for the screws on the tubes 4 and 6, review
step 3for the correct assembly of those tubes.
STEP 3
Hardware:
AM6x12
1
Pc
CM6x45
6
Pcs
STEP 4
Hardware:
BM6x30
2
Pcs
CM6x45
2
Pcs
EM6
2
Pcs
2
3
4
5
6
A
10
(Front)
(Back)
(Front)
7
6
4
E
C
B
Please pay attention to
the orientation of the
holes onall thetubes

P. 7 RTA-7310D P. 7
Assemble the top shelf support tubes 8to the shelf horizontal tube 9with
screws C.
Assemble the tubes 8and 9to the top shelf panel 14 with screws B.
STEP 5
Hardware:
CM6x45
2
Pcs
STEP 6
Hardware:
BM6x30
6
Pcs
9
Please pay attention to
the orientation of the
holes on the tubes
8
8
8
8
9
14
With the help of another person, assemble the main panel 13 to the
tubes 8with screws Bmaking sure the bottom surface faces UP like
shown in the illustration.
STEP 7
Hardware:
BM6x30
4
Pcs
8
8
(Bottom surface)
(Top surface)
13

P. 8 RTA-7310D P. 8
With the help of another person, assemble the main panel 13 to the
frames 1, 2and 3and to the tubes 5and 6with screws Bfrom
underneath.
Note: If you don’t see holes for the screws on the tubes 5and 6, review
step 3for the correct assembly of those tubes.
Assemble the casters Fand Gto the CPU panel 11 with screws D,
making sure the Locking casters Fare attached on the same side that
will be considered the FRONT of the cart.
STEP 8
Hardware:
BM6x30
8
Pcs
STEP 9
Hardware:
DM3.5x12
16
Pcs
F
Locking
2
Pcs
G
Non-lock
2
Pcs F
13
1
23
5
6
11
G
G
F

WEIGHT LIMITS
P. 9 RTA-7310D P. 9
44 Lbs.
(20 Kg)
•Do not exceed the indicated weight limits.
•Do not expose the surfaces to direct sunlight or to extreme environmental conditions.
•Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel.
•Do not use solvents or abrasive materials to clean the unit.
•If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop.
•Do not sit on the unit or lean against it.
•Do not allow small children to play under or over the unit.
•Do not allow small children to play with the CPU cart or use it as a vehicle.
•Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be lifted by
at least 2 persons when moving in the same or adjacent rooms.
•Before moving the unit, make sure to secure or remove any object that is heavy or might
fall off. Please note that lifting from the tabletop with too much weight on the product might
lead to part damage/separation.
•When lifting the unit, grab the frame, not the main panel, and use both hands and bend
your knees, not your backs.
•When transporting the unit to places far away, protect and secure the unit to avoid damage
in transit.
•Shall any part of the unit become defective during the warranty period, replacement parts
might be available to you at no charge. Please refer to the last pages on this manual.
•The warranty does not extend to regular wear and tear, nor the manufacturer assumes
liability for damages or consequences due to accidents, incorrect assembly, negligence,
improper use, modifications, or not heeding the above warnings.
CARE, MAINTENANCE AND SAFETY WARNINGS:
ALL DONE!
Give yourself a nice pat on the back.
You did a great job!
You can keep the CPU cart under the
desk or on the side according to your
preference.
88 Lbs.
(40 Kg)
44 Lbs.
(20 Kg)
66 Lbs.
(30 Kg)
66 Lbs.
(30 Kg)
Option 1 Option 2

RTA Products, LLC warrants to the Original Purchaser who acquired anew product from
RTA Products or its authorized resellers that this product will be free from defects in its
workmanship and materials, under normal use and service conditions, as described
herein."Defects" as used in this warranty, is defined as any imperfections that impair the
use of the furniture or product.RTA Products LLC will replace any defective part, at its
discretion, and without charge to the original purchaser other than the freight from the end
consumer to RTA Products.
Replacement parts can only be supplied if parts are available.Items out of production
may be unavailable.This warranty will be effective for the applicable time period
beginning the date of purchase on your original sales receipt.RTA product’s obligation
under this warranty is limited to repairing or replacing products or parts as provided
herein.This product has been designed for and is intended for office and home-office use
only.This warranty is Original Purchaser’s sole remedy for product defects, and this
warranty does not extend to any product, or damage to any product, caused by or
attributed to abuse or misuse, products used for commercial or rental purposes, use
modifications of, or attachments to the product, and products or parts not used,
maintained, or extended hereunder is in lieu of any and all other warranties, express or
implied, including without limitations any implied warranty or merchantability or of fitness
for aparticular purpose.Please note, all desks made with PVC Laminate surface should
not be exposed to direct sunlight, as it may damage the material.Damage of this nature
is not covered under this warranty.
RTA Products will not be responsible for indirect, special, incidental or consequential
damages.This warranty is limited to merchandise purchased in the Continental United
States.Some States do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.This warranty
gives you specific legal rights.You may also have other rights that may vary from state to
state.
RTA Products will advise you of the procedure to follow in making warranty claims.The
following are the procedures for warranty claims:
a. Call us Monday –Friday, from 9am-5pm (Eastern Time) at [phone] to explain
the defect and give your name, address and phone number.Please have ready the
model number of our product, date and place of purchase.You can also write to us by
e-mail to [e-mail] and include the same information.
b. If we determine that replacement will remedy the situation, and in order to determine
the extent or the cause of the defect, purchaser will need to send the part in question
at purchaser’s expense.Once we receive the part, we will examine it and determine
whether the claim is valid (or not), and then proceed to send the replacement.We will
ship the replacement at our expense.
P. 1 0 RTA-7310D P. 1 0
TECHNI MOBILI WARRANTY
DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY
TV Stand/Entertainment Center: 2 YEAR WARRANTY

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts
OR EMAIL US: [e-mail]
P. 11 RTA-7310D P. 11