Technibel MPAF13A0R5I Series User manual

37.4254.058.02 07/2015
Split air conditioner system • Condizionatore d’aria split system
Climatiseurs split • Split-klimagerät
Acondicionador de aire de consola partida sistema split
MPAF13A0R5I--
MPAF13B0R5I--
EG
I
F
D
E
OPERATING INSTRUCTIONS • ISTRUZIONI D’USO
NOTICE D’UTILISATION • BEDIENUNGSANLEITUNG
INSTRUCCIONES DE USO
3742540582-USO-TEC-MPAF13A-B 21-07-2015 10:34 Pagina 1

2
The following symbols used in this manual, alert you to
potentially dangerous conditions to users, service personnel
or the appliance:
This symbol refers to a hazard or unsafe practice which
can result in severe personal injury or death.
This symbol refers to a hazard or unsafe practice which
can result in personal injury or product or property damage.
This air conditioner is equipped with cooling, drying, heating and fan only functions.
Details on these functions are provided below; refer on these descriptions when using the air conditioner.
CONTENTS
NAME OF PARTS AND OPERATION SELECTOR SWITCH 3
INSTALLATION LOCATION 4
ELECTRICAL REQUIREMENTS 4
SAFETY INSTRUCTIONS 4
USING THE REMOTE CONTROL UNIT 4
REMOTE CONTROL UNIT 5
HOW TO SET THE PRESENT TIME 6
COOLING 6
HEATING 6
AUTOMATIC OPERATION 6
DEHUMIDIFYING (DRY) 7
FAN ONLY 7
ADJUSTING THE FAN SPEED 7
AIR IONIZER 7
NIGHT MODE/ENERGY SAVING 7
HIGH POWER MODE 7
SETTING THE TIMER 8
SETTING THE 1 HOUR TIMER 8
SETTING THE HOLIDAY TIMER 8
ADJUSTING THE AIR FLOW DIRECTION 9
OPERATION WITHOUT THE REMOTE CONTROL UNIT 10
CARE AND CLEANING 10
TIPS FOR ENERGY SAVING 11
TROUBLESHOOTING 11
NOTE
PRODUCT INFORMATION
If you have problems or questions concerning your Air
Conditioner, you will need the following information. Model
and serial numbers are on the nameplate on the bottom of
the cabinet.
Model No.
Serial No.
Date of purchase
Dealer’s address
Phone number
ALERT SYMBOLS
EG
WARNING
CAUTION
DECLARATION OF CONFORMITY
This product is marked as it satisfies Directives:
– Low voltage no. 2006/95/EC (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012
+ A1:2006 + A2:2009 con EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010
+ A15:2011).
–Electromagnetic compatibility no. 2004/108/EC, 92/31 EEC and 93/68 EEC. (Standard: EN55014-1 (2006) +
A1(2009) + A2(2011), EN 55014-2 (1997) + A1(2001) + A2 (2008), EN 61000-3-2 (2006) + A1(2009) + A2(2009),
EN 61000-3-3 (2008)
– RoHS2 no.2011/65/EU.
– Regulation (EU) no. 206/2012, of 6 march 2012, concerning the specifications for ecodesign requirements of air
conditioners and fans.
– Regulation (EU) no. 626/2011, of 4 may 2011, concerning the labeling indicating the energy consumption of air
conditioners.
This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation
and/or operating instructions.
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 2

3
NAME OF PARTS AND OPERATION SELECTOR SWITCH
EG
NOTES
lIt is possible to set the air conditioner in order to let
all the lamps always OFF, even during operation.
Be sure that AIR IONIZER mode is OFF. Press
contemporary the IFEEL and FAN buttons on the
remote control unit for more then 5 seconds.
Repeat the same procedure to set again the normal
operation conditions.
lIn case of troubleshooting the air conditioner
diagnostic system activates the lamps accordingly,
even if they are set to OFF. See paragraph
TROUBLESHOOTING for further details.
1. Remote control unit.
2. Remote control sensor: Detects the room temperature
around the remote control unit, the air conditioner is
controlled accordingly.
3. Air outlet: Conditioned air is blown out of the air
conditioner through the air outlet.
4.
Air intake: Air from the room is drawn into this section
and passes through air filter which removes dust.
5. Remote control receiver: This section picks up infrared
signals from the remote control unit (Transmitter).
6. Operation selector (without remote control): Push
the button to walk through the operation modes (OFF,
COOL and HEAT)
7. OPERATION lamp: This lamp lights up during operation
(green led) and when it is in standby (red led).
8. Cooling lamp: This lamp lights up when the air
conditioner is operating in cooling mode.
9. Heating lamp: This lamp lights up when the air
conditioner is operating in heating mode.
10.Dry lamp: This lamp lights up when the air conditioner
is operating in dry mode.
The OFF position does not disconnect the power. Use
the main power switch to turn off power completely.
WARNING
2
1
3
4
5
6
78
91011
11.Room temperature and operating error lamp: This
lamp shows the room temperature or the eventual
operating error codes (see table “AUTO DIAGNOSIS”).
Every time that the remote control signal is received
and stored, this lamp shows the set temperature
(setpoint).
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 3

4
EG
HOW TO INSTALL BATTERIES
lRemove trhe lid in the rear part of the remote control unit
and check the settings of the four microswitches as
shown below:
TEMPERATURE SENSOR SELECTOR
lUnder normal conditions the room temperature is detected
and checked by the temperature sensor placed in the
remote controller (I FEEL icon displayed ).This function
is designed to provide a comfortable room temperature
by transmitting the temperature control command from the
location next to you. When using this function, the remote,
control should always be pointed at the air conditioner,
therefore it should be placed in a position in which it is
visible by the indoor unit (for example, do not put it in a
drawer).
lIt is possible to disable the remote controller room sensor
pressing the I FEEL button. In this case the I FEEL icon
on the remote controller display lights off and only the
sensor placed in the air conditioner becomes active.
USING THE REMOTE CONTROL UNIT
lInsert two AAA alkaline batteries of 1,5 V-DC making
sure that point in the direction marked in the battery
compartment.The displayed time flashes.
Press the SEL TYPE button.
Remote controller is now ready for operation.
lThe batteries last average more than six months, anyway
it depends on how much you use the remote control
unit.
Remove the batteries if you do not use the remote control
unit for more than one month.
Replace the batteries when the remote control unit lamp
fails to light, or when the air conditioner does not receive
the remote control unit signals.
lThe batteries of the remote control contain polluted
substances. Exhausted batteries must be disposed
according to the laws in force.
OPERATION WITH THE REMOTE CONTROL UNIT
When using the remote control unit, always point the unit
transmitter head directly at the air conditioner receiver.
HOW TO TURN ON THE AIR CONDITIONER
Press the ON/OFF button to turn the air conditioner on.
The operation lamp (green) will light up, indicating the unit
is in operation (red led if it is in cold draft prevention).
The remote control unit transmits signals to the indoor
unit each time you press a key and at any temperature
change detected by the IFEEL sensor. In case of
troubles (low batteries, remote control placed in a
position not visible by the indoor unit,...) room
temperature control is automatically switched to the
sensor of the indoor unit. In this case, the temperature
around the remote control unit may differ from the
temperature detected in the air conditioner position.
NOTE
SWITCHES
SAFETY INSTRUCTIONS
lRead this booklet carefully before using this air
conditioner. If you still have any difficulties or
problems, consult your dealer for help.
lThis air conditioner is designed to give you
comfortable room conditions. Use this only for its
intended purpose as described in this Instruction
Manual.
lNever use or store gasoline or other flammable vapor or
liquid near the air conditioner. It is very dangerous.
lNever install electrical equipment, which is not
protected with IPX1 protection (protection against
vertical water drop), under the unit.
lThe manufacturer assumes no responsabilities if the
safety regulations or local codes are not observed.
lNever use the power main switch to start or stop the
air conditioner: always use the ON/OFF button on the
remote control unit or the selector switch on the unit.
lDo not let children play with the air conditioner.
lDo not cool the room too much if babies or invalids
are present.
lThis air conditioner is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the air conditioner
by a person responsible for their safety.
WARNING
CAUTION
INSTALLATION LOCATION
lWe recommend this air conditioner to be installed
properly by qualified installation technicians in
accordance with the installation instructions provided
with the unit.
lDo not install this air conditioner where there are
fumes or flammable gases, or in an extremely humid
space such as a green house.
lDo not install the air conditioner where excessively
high heat-generating objects are placed.
lDo not install the air conditioner where the
atmosphere is extremely damp or humid (e.g.
greenhouse or laundry) it could be wetted by drops
of water (i.e. in laundries).
lTo protect the air conditioner from heavy corrosion,
avoid installing the outdoor unit where salty sea
water can splash directly onto it or in sulphurous air
near a spa.
WARNING
ELETRICAL REQUIREMENTS
lBefore installation, check that the voltage of the electric
supply in your home or office is the same as the voltage
shown on the nameplate.
lAll wiring must conform to the local electrical codes.
Consult your dealer or a qualified electrician for details.
lEach unit must be properly grounded with a ground (or
earth) wire or through the supply wiring.
lWiring must be done by a qualified electrician.
NOTE ONLY IF YOU INSTALL MORE THAN ONE
INDOOR UNIT IN THE SAME ROOM
Set unit A, B, C or D with Remote Control (see procedure
in Installation Manual).
PLEASE, SEE THE END
OF THIS MANUAL FOR
DETAILS
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 4

5
EG
REMOTE CONTROL UNIT
DISPLAY
Information is displayed when the remote controller is switched on.
If switched off, only the operating mode, the room temperature and
the clock are shown
Operation mode
Fan speed
High speed
Automatic Medium speed
Low speed
Displayed when
transmitting data
Set point
temperature
I FEEL mode is active
(remote controller
sensor active)
Timer modes
Automatic
Cooling
Heating
Dehumidification
Fan
C
Clock
Room
temperature
Night
mode
Oscillation
Flap
Air ionizer / menu
HIGH POWER
mode
TRANSMITTER
When you press the
buttons of the remote
control unit, the
mark appears
on the display to
transmit the setting
changes to the
receiver in the air
conditioner.
HOURS AND MINUTES SETTING
BUTTONS
With these buttons is possible to set the
clock and the timer. For details refer to
paragraphs “ SETTING THE HOUR” and
“SETTING THE TIMER”.
TIMER SELECTION BUTTON
Press this button to select the type of timer
to activate. For details refer to paragraph
“SETTING THE TIMER”.
MODE SELECTOR BUTTON
Press this button to modify the air
conditioner mode.
(heating)
The air conditioner makes the room warmer.
(automatic)
When this setting is selected, the air
conditioner calculates the difference
between the thermostat setting and the
room temperature and automatically
switches to the "cool" or "heat" mode.
C
TEMPERATURE SETTING BUTTONS
- (cooler)
Press this button to decrease the set
temperature.
+ (warmer)
Press this button to increase the set
temperature.
SENSOR
A temperature
sensor inside the
remote control unit
detects the room
temperature.
CLOK AND TIMER SETTING BUTTON
Press this button in order to:
• set the clock
• set the ON/OFF timer
For details refer to paragraphs “SETTING
THE HOUR” and “SETTING THE TIMER”.
IFEEL/IFEEL C SENSOR SELECTOR
Press this button to modify the active setting
for room temperature detection (from remote
controller to air conditioner and viceversa).
“FAN “ BUTTON (fan speed)
Fan speed is automatically
selected by the microcomputer.
High speed.
Medium speed.
Low speed.
ON/OFF BUTTON
This button turns the air conditioner ON
and OFF.
FLAP BUTTON
Press this button in order to select the
desired function.
Fixed: six position
Continous oscillations
Automatically oscillations
NIGHT/ECO BUTTON
Press this button in order to select the
NIGHT/ECO mode.
AIR IONIZER / MENU BUTTON
Press this button in order to select the mode
“Air ionizer” or to enter the functions menu.
“HIGH POWER” BUTTON
Press this button in order to select the HIGH
POWER mode.
MODE SELECTOR BUTTON
Press this button to modify the air
conditioner mode.
(cooling)
The air conditioner makes the room cooler.
(dry)
The air conditioner reduces the humidity in
the room.
(automatic)
When this setting is selected, the air
conditioner calculates the difference
between the thermostat setting and the
room temperature and automatically
switches to the "cool" or "heat" mode.
(fan)
The air conditioner works only as a
circulation fan.
blinking or fixed
Inverter model
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 5

6
EG
C
Verify that the unit is connected to the
main power and the OPERATION lamp
is light up.
1.Set the selector to COOL (symbol
on the display).
2.Press the +/- buttons (temperature
selection) to set the desired temperature
(the temperature range is between 32 °C
max. and 10 °C min.).
HOW TO SET THE PRESENT TIME
HEATING
1. Press the button ST three times.
The time indication alone flashes.
2. Press the H button until the present time hour is
displayed. Press the M button until the present time
minutes are displayed. The display will automatically
stop flashing.
ONON ON
Δ1 H Δ1 H
MIN. MAX.
A
B
C
C
B
A
27
26
25
24
23
22
21
20
19
AUTOMATIC OPERATION
1.Set the selector to HEAT (symbol on the display.
2.Press the +/- buttons (temperature selection) to set the desired
temperature (the temperature range is between 32 °C max.
and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN button to select the fan speed.
For several minutes after the start of heating operation, the
indoor fan will stop until the indoor heat exchanger coil has
warmed up sufficiently. This is because the COLD DRAFT
PREVENTION SYSTEM is operating. During this period, the
OPERATION lamp remains lit (red led).
NOTE
DEFROSTING OF OUTDOOR UNIT HEAT
EXCHANGER
When the outdoor temperature is low, frost or ice may
appear on the heat exchanger coil, reducing the heating
performance. When this happens, a protection function for
the heat exchanger defrosting is activated. During this
function operation, the fan of the indoor unit stops. Heating
operation restarts after several minutes. (This interval will
vary slightly depending on the room and outdoor
temperature).
HEATING PERFORMANCE
A heat pump conditioner heats a room by taking heat from
outside air. The heating efficiency will fall off when the
outdoor temperature is very low. If enough heat is not
obtained with this air conditioner, use another heating
appliance in conjunction with it.
1.Set the or selector to AUTO (symbol on
the display; also the symbol or remains displayed).
2.Press the
+/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
When this setting is selected, the air conditioner calculates
the difference between the thermostat setting and the room
temperature and automatically switches to the COOL or
HEAT mode as appropriate, regardless of the symbol
displayed.
3.Press the FAN selector button to the setting you want.
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
Example of operation diagram in the (Auto) mode with
the set room temperature at 23°C.
NOTE
The air conditioner changes the operation mode (from cool
to heat or vice versa, if one of the following conditions
occurs:
-ZONE A: changes if the difference between the room
temperature and the temperature set on the remote control
unit is at least 3°C..
-ZONE B: changes if the difference between the room
temperature and the temperature set on the remote control
unit is at least 1°C, one hour after the compressor stop.
- ZONE C: never changes if the difference between the
room temperature and the temperature set on the remote
control unit is no more than 1°C.
COOLING
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN button to select the fan speed.
1
3
2
NOTE
2
1
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 6

7
EG
1.Set the button to DRY. The icon is displayed.
2.Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
DEHUMIDIFYING (DRY)
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
lUse DRY operation when you want to reduce the humidity
in the room.
lOnce the room temperature reaches the set level, the unit
repeats the cycle of turning on and off automatically .
lDuring DRY operation, the fan speed is automatically set
(Remote control lamp is ON) to prevent overcooling.
lDry operation is not possible if the indoor temperature is
10 °C or less.
NOTE
FAN ONLY
If you want to make air circulate without any temperature
control, press button until only the fan symbol
appears on the display.
ADJUSTING THE FAN SPEED
AUTOMATIC
Simply set the FAN selector to the position.A
microcomputer automatically controls the fan speed when
the AUTO mode is selected. When the air conditioner starts
operating, in heating or cooling, the fan speed varies (high
- medium - low - very low) according to the thermal load of
the room.
The automatic speed is not available in FAN ONLY mode.
NOTE
High speed Med. speed Low speed
MANUAL
If you want to manually adjust speed just set the FAN selector
as desired.
AIR IONIZER
Pressing the button (symbol on the display)
the air ionizer is activated; this is very effective to prevent
bad odours and to eliminate bacteria and micro-organisms.
NOTE
The filter is active only if the internal fan is operating.
NIGHT MODE / ENERGY SAVING
lThis mode enables you to save energy.
1. Set the or selector to cool, dry or heat.
2. Press the button.
3. The mark appears on the display. Press the
button again to release the function.
What does the NIGHT mode mean?
When you select the NIGHT mode, the air conditioner will
modify automatically the set temperature after 60 minutes.
This enables you to save energy without sacrificing your
comfort.
OPERATING MODE SET TEMPERATURE CHANGE
Heating Lowered by 2 °C
Cooling and Dry Raised by 1 °C
During the NIGHT mode the internal fan speed is
automatically lowered and reduces the noise.
NOTA
HIGH POWER MODE
When this mode is active the internal fan speed is set
automatically and the air conditioner operates at the
maximum power in the selected operating mode (cooling
or heating).
NOTE
During the high power operation the room temperature
could not correspond to the set temperature.
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 7

8
EG
A) HOW TO SET THE ON TIME
1. Press the ST button once.
The ON and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display will
change automatically back to show the
present time after 10 sec.
3. Press the ON/OFF button to start the air
conditioner.
4. Press the button to activate the ON
timer.
B) HOW TO SET THE OFF TIME
1. Press the ST button twice.
The OFF and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display will
change automatically back to show the
present time after 10 sec.
3. Press the ON/OFF button to start the air
conditioner.
4. Press the button two times to
activate the OFF timer.
C) HOW TO SET A PROGRAM FOR
DAILY ON/OFF OPERATION (OR
VICEVERSA)
1. Set the timer ON/OFF as shown in A)
and B).
2. Press the ON/OFF button to start the air
conditioner.
3. Press three times the button to
activate the DAILY timer.
SETTING THE TIMER
After timer setting, press ST button in order to check the
ON/OFF setting time.
NOTE
TIMER SETTING PROCEDURE.
lPress four times the button.The 1
HOUR TIMER mark will appear on the
display.
CANCELLATION PROCEDURE
lPress the ON/OFF button to turn the air conditioner off.
lWait for the indoor unit to stop operating.
lPress the ON/OFF button again to turn the air conditioner
on.
SETTING THE 1 HOUR TIMER
This function causes the unit to operate for one hour at the
set conditions, regardless of whether the unit is on or off.
C
4
2
2
3
1
SETTING THE HOLIDAY TIMER
The Holiday Timer function allows you to activate the indoor
unit (either it is the only one of a monosplit system or one
unit of a multisplit system), with a dalay up to 99 days you
can set for the Daily Timer, On Timer, Off Timer functions
(not available for 1 HOUR TIMER) already explained in this
manual.
With this function you can set the air conditioner to be
switched on again after a long week end, a holiday of one
week or more, ecc…
To activate this function you have to follow the following
steps in order :
1. Keep pressed the button “TIMER SELECTION” of the
remote control unit (clock figure) for more than 6~7
seconds. In this way you enter the menu to select the
number of days of delay.
2. Select the desired timer (Daily Timer, On Timer, Off
Timer) pressing on the same button “TIMER
SELECTION”.
3. Set the desired number of days of delay using the button
“+” .
4. Keep pressed again the button “TIMER SELECTION” for
more than 6~7 seconds. You enter again the normal
menu of the remote control unit.
At this point, the symbol of the desired timer will flash and
the selected timer will be activated only after the set number
of delay days.
C
1 - 2 - 4
3
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 8

9
EG
ADJUSTING THE AIR FLOW DIRECTION
HORIZONTAL (manual)
The horizontal air flow can be adjusted by moving the lever
to the left or right, as indicated in the following figure.
VERTICAL (with remote control unit)
Make sure that the remote control unit has been turned on. Press
the FLAP button to select the flap function
Fixed:
six
position
Continous
oscillations Automatical oscillations
Do not move the flap with your hands when the air
conditioner is running.
CAUTION
NOTES lThe flap automatically closes when the unit
is off.
lWhen the unit starts in heating operation,
the fan stops and the flap is in the 4 position
(if automatical oscillation is selected) until
the air being blown out of the unit begins to
warm. Once the air warms up, the flap
position and fan speed change to the settings
specified with the remote control.
• Use the FLAP button on the remote control to adjust
the position of the flap. If you move the flap by hand,
the factual flap position and the flap position on the
remote control may no longer match. If this should
happen, shut off the unit, wait for the flap to close,
and then turn on the unit again; the flap position will
now be normal again.
• Do not have the flap pointed down during cooling
operation. Condensation may begin to form around the
air vent and drip down.
CAUTION
Lever
Up
Down
Flap
Air outlet
grille
HOW TO ADJUST THE FLAP DIRECTION
Zone «A»
for cooling and dehumidifyng Zone «B»
for heating
Set vertical vanes to the front position during
COOLING/DRY operation if humidity is high.
If the vertical vanes are set to the left-most or right-most
position, condensation will form around the air outlet
and drip off.
CAUTION
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 9

10
FILTER CLEANING
Use a vacuum cleaner to remove light dust. If there is
sticky dust on the filter, wash the filter in lukewarm, soapy
water, rinse it in clean water, and dry it.
1. Grasp both ends of the front panel and pull it towards you
and up.
2. Push the filter up slightly, and then pull it down. Clean the
air filter.
AIR FILTER
The filter behind the front panel should be checked and
cleaned at least once every three months or more frequently
in case of excessive dust in the room.
Do not use fire or air dryer to dry the filter, to avoid
deformation or fire hazard.
HOW TO REPLACE THE FILTER
1. With the «FRONT» mark facing you, slide the filter up
into the unit and insert it in its place.
2. After installing the filter, close the front panel.
EG
lNever use solvents, or harsh chemicals when cleaning the
indoor unit. Do not wipe the plastic casing using very hot
water.
lSome metal edges and the vanes are sharp and may
cause injury if handled improperly; be especially careful
when you clean these parts.
lThe internal coil and other components of the outdoor
unit must be cleaned every year. Consult your dealer or
service centre.
CAUTION
2. WHEN THE AIR CONDITIONER IS RUNNING
If you want to turn off the air conditioner push the
OPERATION selector until the unit is in standby (red
operating lamp).
Power failure during operation.
In the event of power failure, the unit will stop. When the
power is resumed, the unit will restart automatically after 3
minutes.
NOTE
If you have lost the remote control unit or it has troubles,
follow the steps below.
1. WHEN THE AIR CONDITIONER IS STOPPED
If you want to turn on the air conditioner push the
OPERATION selector to select the desired mode (COOL
or HEAT).
OPERATION WITHOUT THE REMOTE
CONTROL UNIT
The air conditioner will start in HIGH fan speed.
The temperature setting is 25°C for cooling mode and
21°C for heating mode.
NOTE
CARE AND CLEANING
lMaintenance operations must be carried out by specially
trained personnel.
lFor safety, be sure to turn the air conditioner off and also
to disconnect the power before cleaning.
lDo not pour water on the indoor unit to clean it. This will
damage the internal components and cause an electric
shock hazard.
WARNING
CASING AND GRILLE (INDOOR UNIT)
Clean the casing and grille of the indoor unit with a vacuum
cleaner brush, or wipe them with a clean, soft cloth.
If these parts are stained, use a clean cloth moistened with
a mild liquid detergent.
When cleaning the grille, be careful not to force the vanes
out of place.
OPERATION
selector
HOW TO REMOVE THE FILTER
Front panel
Air filter
Insert into the groove on the unit
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 10

11
TIPS FOR ENERGY SAVING
DO NOT:
lBlock the air intake and outlet of the unit.
If they are obstructed, the unit will not work well, and
may be damaged.
lLet direct sunlight into the room. Use sunshades,
blind or curtain.
DO:
lAlways try to keep the air filter clean. A clogged filter
will impair the performance of the unit.
lTo prevent conditioned air from escaping, keep windows,
doors and any other openings closed.
TROUBLESHOOTING
WARNING
lThe use of portable telephones near the air conditioner
may cause disturbance to its normal operation and must
be avoided. In case abnormal operation is noticed,
(OPERATION lamp lights, but the air conditioner will not
run) to restore normal operation turn-off electric supply
for about 3 minutes, by disconnecting the main switch or
the wall plug, then start again the air conditioner.
If your air conditioner does not work properly, first check
the following points before requesting service.
If it still does not work properly, contact your dealer or service
centre.
Trouble: the air conditioner does not run at all.
Possible cause:
1. Power failure.
2. Leakage breaker tripped.
3. Operation button is OFF.
4. Batteries in remote control unit have run down.
Remedy:
1. Restore power.
2. Contact service centre.
3. Press the button again.
4. Replace batteries.
Trouble: Poor cooling or heating performance.
Possible cause:
1. Dirty or clogged air filters.
2. Heat source or many people in room.
3. Doors and/or windows are open.
4. Obstacle near air intake or air discharge port.
5. The set temperature on the remote control unit is too
high.
6. Outdoor temperature is too low (heat pump version).
7. Defrosting system does not work (heat pump version).
Remedy:
1. Clean air filters to improve airflow.
2. Eliminate heat source if possible.
3. Shut them to keep the heat or cold out.
4. Remove it to ensure good airflow.
5. Set the right temperature on the remote control unit.
6. Try to use a back-up heater.
7. Consult your dealer.
Trouble: Clicking sound is heard from the air conditioner.
Possible cause:
1. During operation, any plastic parts may expand or shrink
due to a sudden temperature change. In this event, a
clicking sound may occur.
Remedy:
1. This is normal, and the sound will disappear when an
even temperature is settled.
EG
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 11

12
EG
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 12
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E0 lF F
Unit has not been addressed correctly. Operating mode selected is not compat- ible with the system (ex. heating mode has been selected, when the system was in cooling mode, or vice versa).
Fan is stopped and flap is closed. The system restarts automatically as soon as the unit is addressed correctly. Fan is stopped and flap is closed. The system restarts automatically as soon as a correct operating mode is selected.
Set the outdoor/indoor unit refrigerant circuit address (see Installation Instructions) Select an available or compatible mode with the other units of the system.
E1 O O F
Error on the outdoor unit. Fan is stopped and flap is closed.
The system restarts automatically as soon as the problem on the out- door unit is solved.
Check the error code using the appro- priate LEDs on the PCB of the outdoor unit. Follow the indications of the diagnosis for the outdoor unit.
AUTO-DIAGNOSIS TABLE O = LED OFF l = LED ON F = Flashing LED

13
EG
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 13
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E3 F F F
Communication error between the out- door unit and the indoor unit
Fan is stopped and flap is closed after 30 seconds of missing com- munication. The system restarts automatically as soon as the communication is recovered.
Check that connections between C1 and C2 on outdoor and indoor terminal block are correct (C1 terminals con- nected together, C2 terminals connect- ed together). Check that a shielded communication cable has been used. Check that the dip-switch SW1 for com- munication address setting is in the correct position. Check that all earth cables are proper- ly connected to every terminal. Check that the shield of the communi- cation cable is properly connected to every terminal. Check the communication fuse on out- door and indoor unit. Check that the outdoor unit has power supply and that it is working. Check that all PCBs are powered on. Be sure that power supply has not been connected to the communication terminals. Check that there are no burnt signs on the PCBs, in particular close to commu- nication cables. Check that the fan motor is not dam- aged and it doesn’t create short circuit on the indoor PCB.
O = LED OFF l = LED ON F = Flashing LED

14
EG
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 14
ERROR LEDS
OPERATION TIMER STANDBY POSSIBLE CAUSE SYSTEM BEHAVIOUR SOLUTION
E4 F F O
Defective or not connected indoor coil temperature sensor.
Fan is stopped and flap is closed. The system restarts automatically as soon as the sensor is repaired.
Check that the sensor is properly con- nected to the PCB as shown in the electrical wiring diagram. Check that the sensor is not damaged and, if necessary, replace it.
E5 F O F
Defective or not connected room air tem- perature/humidity sensor.
Fan is stopped and flap is closed. The system restarts automatically as soon as the sensor is repaired.
Check that the sensor is properly con- nected to the PCB as shown in the electrical wiring diagram. Check that the sensor is not damaged and, if necessary, replace it.
E6 O F F
Fan motor error. Fan is stopped and flap is closed.
The system restarts automatically after some seconds.
Check that the fan motor is properly connected to the PCB as shown in the electrical wiring diagram. Check that the fan motor is not locked. Check that the fan motor is not dam- aged and, if necessary, replace it.
E8 O F O
Combination between outdoor unit and indoor units is not correct.
Fan is stopped and flap is closed. Check that you have selected, during
the installation of the system, a proper combination between outdoor unit and indoor units. Check that none of the indoor units of the system has a communication error. If present, first solve this error.
NOTE: If the trouble is not solved with the above actions, contact your service centre. O = LED OFF l = LED ON F = Flashing LED

15
INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE 2012/19/EU
At the end of its working life this equipment must not be disposed of as an household waste.
It must be taken to special local community waste collection centres or to a dealer providing this service.
Disposing of an electrical and electronic equipment separately avoids possible negative effects on the environment
and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled
to obtain significant savings in energy and resources.
In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.
INFORMATION FOR CORRECT DISPOSAL OF THE BATTERY IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE 2006/66/EC
Please replace battery when its electricity charge is used up: please do not eliminate this battery together with normal
household waste. It must be taken to special local community waste collection centres or to a dealer providing this
service. Disposing of a battery separately avoids possible negative effects on the environment and human health
deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant
savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the battery is
marked with a crossed-out dustbin.
REGULATION (EU) No. 517/2014 - F-GAS
The unit contains R410A, a fluorinated greenhouse gas with a global warming potential (GWP) of
2087.50. Do not release R410A into the atmosphere.
EXPLANATION AND USE OF THE REMOTE CONTROL UNIT’S MICROSWITCHES
Switch 1 and 2: These switches are used to match the remote control with the
specific internal units.
Switch 3 and 4: these switches have been provided for future use; they have no
function today. Keep them in OFF position.
Switch 5 and 6: Factory setting. Keep them in ON position.
HOW TO REMOVE BATTERIES
lRemove the lid.
lPress the battery toward the negative end
and lift it out by its positive end (as shown in
the figure).
lRemove the other battery in the same way.
TRASMISSION FREQUENCY SETTING OF THE REMOTE CONTROL UNIT
C
(1)
2)
The unit receiver receives the signals at the frequency of 38 kHz.
The remote control unit, supplied with the unit, must be set to transmit the signals at the
same frequency of the receiver.
Proceed as follows:
lInsert the batteries in the battery compartment.
lPress and hold the menu button (1) for at least 7 seconds (until you enter the function
“menu”).
lAt this point the display will show 00. Press the temperature setting button + (2) until the
display shows the number 38.
lPress and hold the menu button (1) again for at least 7 seconds, to exit the “menu”.
ATTENTION: THIS OPERATION MUST BE REPEATED AT EVERY BATTERY
REPLACEMENT.
EG
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 15

I
2
NOME DELLE PARTI E SELETTORE DI FUNZIONAMENTO 3
LUOGO DI INSTALLAZIONE 4
REQUISITI ELETTRICI 4
ISTRUZIONI DI SICUREZZA 4
USO DEL TELECOMANDO 4
TELECOMANDO 5
COME REGOLARE L’OROLOGIO 6
RAFFREDDAMENTO 6
RISCALDAMENTO 6
FUNZIONAMENTO IN AUTOMATICO 6
DEUMIDIFICAZIONE 7
VENTILAZIONE 7
SCELTA VELOCITÀ VENTILATORE 7
IONIZZATORE D’ARIA 7
PROGRAMMA NOTTURNO/RISPARMIO ENERGIA 7
PROGRAMMA HIGH POWER 7
REGOLAZIONE DEL TIMER 8
REGOLAZIONE DEL TIMER 1 ORA 8
REGOLAZIONE DEL HOLIDAY TIMER 8
REGOLAZIONE DEL FLUSSO D’ARIA 9
FUNZIONAMENTO SENZA TELECOMANDO 10
CURA E MANUTENZIONE 10
CONSIGLI PER IL MASSIMO CONFORT E IL MINIMO CONSUMO 11
IDENTIFICAZIONE E SOLUZIONE PROBLEMI DI FUNZIONAMENTO 11
Questo condizionatore d’aria è dotato delle funzioni di raffreddamento, deumidificazione, riscaldamento e ventilazione
I dettagli su queste funzioni sono forniti di seguito; riferitevi a queste descrizioni quando usate il condizionatore d’aria.
INDICE
NOTA
In caso di difficoltà o se si hanno dei dubbi riguardo al
condizionatore d’aria, sono necessarie le seguenti
informazioni. I numeri del modello e di serie si trovano sulla
targhetta del nome, sulla parte inferiore del mobile.
No. del modello
No. di serie
Data di acquisto
Indirizzo del rivenditore
Numero di telefono
INFORMAZIONI RIGUARDANTI IL PRODOTTO SIMBOLI DI AVVERTIMENTO
I seguenti simboli sono usati in questo manuale per mettere
in guardia l’utente ed il personale di servizio sulle condizioni
potenziali di pericoli personali o di danni al prodotto.
Questo simbolo si riferisce a pericoli o a interventi che
possono causare ferite gravi o la morte.
Questo simbolo si riferisce a pericoli o a interventi che
possono causare danni al prodotto.
AVVERTIMENTO
PRECAUZIONE
DICHIARAZIONE DI CONFORMITÀ
Questo prodotto è marcato in quanto conforme alle Direttive:
– Bassa Tensione n. 2006/95/CE (Standard: EN60335-2-40:2003 (incl. Corr.:2006) + A11:2004 + A12:2005 + A13:2012
+ A1:2006 + A2:2009 with EN 60335-1:2002 + A11:2004 + A1:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010
+ A15:2011).
– Compatibilità Elettromagnetica n. 2004/108/CE, 92/31 CEE e 93/68 CEE. (Standard: EN55014-1 (2006) + A1(2009)
+ A2(2011), EN 55014-2 (1997) + A1(2001) + A2 (2008), EN 61000-3-2 (2006) + A1(2009) + A2(2009),
EN 61000-3-3 (2008)
– RoHS2 n.2011/65/UE.
– Regolamento (UE) n. 206/2012, del 6 marzo 2012, relativo alle specifiche per la progettazione ecocompatibile dei
condizionatori d’aria e dei ventilatori.
– Regolamento (UE) n. 626/2011, del 4 maggio 2011, relativo all’etichettatura indicante il consumo d’energia dei
condizionatori d’aria.
Questa dichiarazione sarà nulla nel caso di impiego diverso da quello dichiarato dal Fabbricante e/o di mancata
osservanza, anche solo parziale, delle istruzioni d'installazione e/o d'uso.
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 2

I
3
NOME DELLE PARTI E SELETTORE DI FUNZIONAMENTO
1. Telecomando.
2. Sensore: rileva la temperatura ambiente attorno al
telecomando; il condizionatore è regolato dalla
temperatura rilevata.
3. Uscita aria: distribuisce nel locale l’aria trattata.
4. Aspirazione aria: l’aria ambiente viene aspirata e passa
attraverso il filtro che trattiene la polvere.
5. Ricevitore: riceve i segnali inviati dal telecomando.
6. Selettore funzionamento (senza telecomando):
Premere questo tasto per passare da una funzione
all’altra (OFF, COOL e HEAT).
7. Spia funzionamento: si accende quando l’unità è in
funzione (led verde) e quando è in standby (led rosso).
8. Spia raffreddamento: Si accende quando il
condizionatore funziona in raffreddamento.
9. Spia riscaldamento: Si accende quando il
condizionatore funziona in riscaldamento.
10.Spia deumidificazione: Si accende quando il
condizionatore funziona in deumidificazione.
La posizione OFF non interrompe l’alimentazione
elettrica. Usate l’interruttore principale per isolare il
condizionatore d’aria.
AVVERTIMENTO
NOTE
lE’ possibile impostare il condizionatore in modo da
mantenere sempre spente, anche durante il
funzionamento, tutte le spie.
Per ottenere ciò assicurarsi che la funzione
IONIZZATORE D’ARIA sia OFF, poi premere
contemporaneamente per più di 5 secondi i tasti
IFEEL e FAN del telecomando.
Ripetendo la procedura vengono ripristinate le
normali condizioni di funzionamento.
lIn tutte le situazioni di guasto rilevate dal sistema di
diagnostica del condizionatore le spie, anche se
impostate per lo spegnimento, vengono attivate in
accordo all’anomalia da segnalare. Vedi paragrafo
IDENTIFICAZIONE E PROBLEMI DI FUNZIONAMENTO
per ulteriori informazioni.
2
1
3
4
5
6
78
91011
11.Spia temperatura ambiente e errori di
funzionamento: Segnala la temperatura ambiente o
gli eventuali codici di errore di funzionamento (v. tabella
AUTO-DIAGNOSI).
Ogni volta che il segnale del telecomando viene rivevuto
e memorizzato, questa spia segnala la temperatura
impostata (setpoint).
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 3

I
4
SELETTORE DEL SENSORE DI TEMPERATURA
lIn condizioni normali la temperatura ambiente viene rilevata
e controllata dal sensore di temperatura posizionato
all’interno del telecomando (icona IFEEL attiva sul display).
Questa funzione permette di creare una temperatura
ambiente ottimale perché il telecomando trasmette la
temperatura dalla posizione in cui vi trovate. Usando questa
funzione, il telecomando deve sempre essere indirizzato
verso il condizionatore, quindi è opportuno che si trovi in
una posizione di visibilità rispetto all’unità interna (ad
esempio non metterlo in un cassetto).
lE’ possibile disattivare il sensore di temperatura del
telecomando premendo il tasto I FEEL. In tal caso la
relativa icona sul display si spegne e diventa operativo
solo il sensore presente all’interno dell’unità.
INSERIMENTO DELLE BATTERIE
lRimuovere il coperchio sul retro del telecomando e
verificare che i quattro microinterruttori siano impostati
come in figura:
USO DEL TELECOMANDO
lInserire due batterie da 1,5 V-DC tipo AAA alcaline
rispettando la polarità indicata sul telecomando.
L’indicazione dell’ora sul display lampeggia.
Premere il tasto SEL TYPE.
Il telecomando ora é pronto per funzionare.
lLa durata media delle batterie è superiore ai sei mesi e
comunque dipende dalla frequenza con cui si usa il
telecomando.
Rimuovere le batterie nel caso di lungo inutilizzo del
telecomando (oltre un mese).
Sostituire le batterie quando la spia di trasmissione dati
del telecomando non lampeggia oppure quando il
condizionatore non risponde ai comandi del telecomando.
lLe batterie del telecomando contengono sostanze
inquinanti. Terminata la loro vita utile, devono essere
smaltite secondo le vigenti normative.
FUNZIONAMENTO CON IL TELECOMANDO
Indirizzare il telecomando con la testina del trasmettitore
verso il ricevitore posto sul condizionatore d’aria.
COME ACCENDERE IL CLIMATIZZATORE
Premere il tasto ON/OFF per accendere il climatizzatore.
La spia funzionamento (verde) si accenderà, ad indicare che
l’unità é in funzione (LED rosso durante la protezione
“Prevenzione corrente aria fredda”).
Il telecomando trasmette segnali all’unità interna ogni
volta che si preme un tasto e ad ogni variazione della
temperatura rilevata dal sensore IFEEL.
In caso di inconvenienti (batterie scariche, telecomando
posizionato in area non visibile dall’unità interna,...), il
controllo della temperatura ambiente viene automati-
camente commutato sul sensore dell’unità interna. In
questi casi la temperatura vicino al telecomando può
differire dalla temperatura rilevata nella posizione del
condizionatore d'aria.
NOTA
Impostare unità A, B, C o D con il telecomando (v.
procedura in Manuale di Installazione).
NOTA
lNon installare questo condizionatore d’aria dove ci
sono fumi, gas infiammabili o molta umidità, come in
una serra.
lNon installare il condizionatore dove ci sono
apparecchiature che generano un calore eccessivo.
lNon installare l'unità interna in locali dove potrebbe
essere investita da spruzzi d'acqua (es. lavanderia).
lPer proteggere il condizionatore d’aria dalla
corrosione eccessiva, non installate l’unità esterna
dove può essere esposta direttamente agli spruzzi
d’acqua marina o a vapori solforosi nelle stazioni
climatiche.
REQUISITI ELETTRICI
lPrima dell’installazione assicuratevi che la tensione
dell’alimentazione elettrica di rete sia uguale a quella
indicata sulla targhetta del condizionatore d’aria.
lTutti gli allacciamenti elettrici devono essere conformi
alle normative elettriche locali. Per i dettagli consultare il
rivenditore o un elettricista.
lCiascuna unità deve essere collegata correttamente a
massa, con un filo di terra.
lGli allacciamenti elettrici devono essere eseguiti da un
elettricista specializzato.
ISTRUZIONI DI SICUREZZA
lLeggete attentamente questo manuale prima di usare
il condizionatore d’aria. In caso di dubbi o problemi
rivolgetevi al rivenditore o al centro assistenza
autorizzato.
lQuesto condizionatore d’aria è stato progettato per
creare condizioni climatiche ideali nella vostra stanza.
Usatelo soltanto per questo scopo specifico e come
descritto in questo manuale.
lMai usare o conservare benzina o altri liquidi infiammabili
vicino al condizionatore. È molto pericoloso.
lNon installare sotto l’unità apparecchiature elettriche
non protette con grado di protezione IPX1 (protezione
all’acqua a caduta verticale).
lIl costruttore non si assume responsabilità alcuna nel
caso in cui le norme di sicurezza e antinfortunistiche non
vengano rispettate.
AVVERTIMENTO
PRECAUZIONE
LUOGO DI INSTALLAZIONE
l
Si raccomanda di far installare questo condizionatore
d’aria da un tecnico qualificato seguendo le istruzioni
di installazione allegate.
AVVERTIMENTO
lNon accendete e spegnete il condizionatore d’aria
mediante l’interruttore generale. Usate sempre il
pulsante ON/OFF sul telecomando o il selettore di
funzionamento sull’unità.
lNon lasciate giocare i bambini con il condizionatore
d’aria.
lNon raffreddate eccessivamente la stanza se ci sono
bambini molto piccoli o degli invalidi.
lIl condizionatore non è destinato ad essere usato da
persone (bambini compresi) le cui capacità fisiche,
sensoriali o mentali siano ridotte, oppure con
mancanza di esperienza o di conoscenza, a meno
che esse abbiano potuto beneficiare, attraverso
l’intermediazione di una persona responsabile della
loro sicurezza, di una sorveglianza o di istruzioni
riguardanti l’uso del condizionatore.
SOLO SE VIENE INSTALLATA PIU’ DI UNA
UNITA’ INTERNA NELLA STESSA STANZA
INTERRUTTORI
PER DETTAGLI, V. IN
FONDO AL MANUALE
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 4

I
5
TELECOMANDO
VISORE
Visualizza le informazioni quando il telecomando è acceso.
Modo di funzionamento
Velocità ventilatore
Alta velocità
Automatico Media velocità
Bassa velocità
Conferma trasmissione dati
al climatizzatore
Temperatura
impostata
Indica che il climatizzatore
funziona in modalità I FEEL
(sensore telecomando attivo)
Programma
notturno
Indica i tipi di
timer
Automatico
Raffreddamento
Riscaldamento
Deumidificazione
Ventilazione
C
Orologio
Temperatura
ambiente
Oscillazione
Flap
Programma
HIGH POWER
Ionizzatore d’aria / menù
TRASMETTITORE
Quando vengono
premuti i pulsanti del
telecomando, il
simbolo si
accede sul visore per
trasmettere i
cambiamenti della
regolazione al
ricevitore del
climatizzatore.
PULSANTI REGOLAZIONE ORE E
MINUTI
Premendo questi pulsanti è possibile
impostare l’ora e il timer.
Per dettagli vedere le sezioni
“COME REGOLARE L’OROLOGIO” e
“REGOLAZIONE DEL TIMER”.
PULSANTE SELEZIONE TIMER
Premendo questo pulsante sul display
viene attivata la procedura per
l’impostazione del timer.Per dettagli vedere
esempio “REGOLAZIONE DEL TIMER”.
PULSANTE MODO DI FUNZIONAMENTO
Premere questo pulsante per modificare il
funzionamento del condizionatore.
(riscaldamento)
Il condizionatore riscalda il locale.
(automatico)
Quando viene scelta la posizione
“automatico” il microprocessore sceglie
automaticamente tra raffreddamento e
riscaldamento in base alla differenza tra la
temperatura ambiente e quella impostata
sul telecomando.
C
PULSANTI SELEZIONE TEMPERATURA
- (più freddo)
Premere questo pulsante per diminuire la
temperatura selezionata.
+ (più caldo)
Premere questo pulsante per aumentare la
temperatura selezionata.
SENSORE
Un sensore di tem-
peratura all’interno
del telecomando ri-
leva la temperatura
ambiente.
PULSANTE REGOLAZIONE OROLOGIO E TIMER
Premere questo pulsante per selezionare le
funzioni:
• impostazione dell’ora
• impostazione del timer ON/OFF
Per dettagli vedere le sezioni “COME
REGOLARE L’OROLOGIO” e
“REGOLAZIONE DEL TIMER”.
SELETTORE SENSORE IFEEL/IFEEL C
Premere il pulsante I FEEL per modificare
l’impostazione del sensore di temperatura
attivo ( da telecomando a Condizionatore e
viceversa).
PULSANTE “FAN” (velocità ventilatore)
La velocità del ventilatore viene
scelta automaticamente dal
microprocessore.
Alta velocità ventilatore.
Media velocità ventilatore.
Bassa velocità ventilatore.
PULSANTE ON/OFF (acceso/spento)
Il pulsante serve per mettere in funzione o
arrestare il climatizzatore.
PULSANTE FLAP
Premere questo pulsante per selezionare la
funzione desiderata.
Fissa: 6 posizioni
Oscillazione continua
Oscillazione automatica
PULSANTE NIGHT/ECO
Premere questo pulsante per selezionare la
funzione NIGHT/ECO.
PULSANTE IONIZZATORE D’ARIA /
MENU’
Premere questo pulsante per selezionare la
funzione “ionizzatore d’aria” o per entrare
nel menù delle funzioni
PULSANTE “HIGH POWER”
Premere questo pulsante per selezionare la
funzione HIGH POWER.
PULSANTE MODO DI FUNZIONAMENTO
Premere questo pulsante per modificare il
funzionamento del condizionatore.
(raffreddamento)
Il condizionatore raffredda l’aria
abbassando la temperatura del locale.
(deumidificazione)
Il condizionatore riduce l’umidità dell’aria
ambiente.
(automatico)
Quando viene scelta la posizione
“automatico” il microprocessore sceglie
automaticamente tra raffreddamento e
riscaldamento in base alla differenza tra
la temperatura ambiente e quella impostata
sul telecomando.
(ventilazione)
Il condizionatore funziona solo come
ventilatore.
lampeggiante o fisso
Modello inverter
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 5

I
6
Esempio: schema funzionamento in modalità (Auto)
con temperatura ambiente impostata a 23 gradi.
Verificare che l’unità sia collegata alla
rete elettrica e che la spia funzionamento
sia accesa.
1.Premere il pulsante fino a far
apparire sul visore il simbolo
RAFFREDDAMENTO .
2.Premere i pulsanti +/- (selezione
temperatura) per impostare la
temperatura desiderata (il campo di
regolazione varia tra 32 °C massimo e
10 °C minimo).
Quando la temperatura esterna scende sotto lo zero sullo
scambiatore di calore esterno si forma del ghiaccio che ri-
duce la potenzialità in riscaldamento. Quando questo acca-
de viene attivata un’opportuna protezione che consente lo
sbrinamento dello scambiatore. In queste condizioni opera-
tive il ventilatore dell’unità interna si ferma.
Il funzionamento in riscaldamento riprende dopo alcuni mi-
nuti in relazione alle temperature ambiente ed esterna.
SBRINAMENTO DELLO SCAMBIATORE DI
CALORE DELL’UNITA’ ESTERNA
FUNZIONAMENTO E CAPACITÀ DI UN
SISTEMA IN “POMPA DI CALORE”
Un condizionatore in versione pompa di calore riscalda
l’ambiente sottraendo il calore all’aria esterna. La capacità
(efficienza) del sistema si riduce quando la temperatura
esterna scende sotto lo zero. Se il condizionatore non riesce
a mantenere un valore sufficiente della temperatura si dovrà
integrare il riscaldamento con un’altra apparecchiatura.
Dopo l’attivazione della funzione riscaldamento, il ventilatore
si fermerà. Questo perché è operativa una protezione
“Prevenzione corrente aria fredda” che abiliterà il normale
funzionamento del ventilatore solo dopo che lo scambiatore
di calore dell’unità interna sarà sufficientemente caldo. Durante
questo periodo la spia funzionamento rimane accesa (led
rosso).
COME REGOLARE L'OROLOGIO
RAFFREDDAMENTO
NOTA
1.Premere il pulsante fino a far apparire sul visore il
simbolo RISCALDAMENTO .
2.Premere i pulsanti +/- (selezione temperatura) per impostare
la temperatura desiderata (il campo di regolazione varia tra
32 °C massimo e 10 °C minimo).
1.Premere il pulsante o fino a far apparire sul
Visore il simbolo AUTOMATICO (anche il simbolo
o rimarrà visualizzato).
2.Premere i pulsanti +/- (selezione temperatura) per
impostare la temperatura desiderata (il campo di
regolazione varia tra 32 °C massimo e 10 °C minimo).
Il condizionatore automaticamente funzionerà passando dal
funzionamento riscaldamento in raffreddamento (o
viceversa) in modo da mantenere la temperatura rilevata,
indipendentemente dal simbolo visualizzato.
3.Premere il pulsante FAN per impostare la velocità ventilatore.
3.Premere il pulsante FAN per impostare la velocità ventilatore.
2. Premere il pulsante H fino a visualizzare l’ora
desiderata.
Premere il pulsante M fino a visualizzare i minuti
desiderati.
L’indicazione dell’ora sul visore cesserà automatica-
mente di lampeggiare dopo 10 secondi.
1. Premere tre volte il pulsante ST.
L’indicazione dell’ora inizierà a lampeggiare.
IL VISORE INDICHERÀ IL VALORE
DELLA TEMPERATURA SELEZIONATA.
TRASCORSI 5 SECONDI DALL’IMPOSTA-
ZIONE DELLA TEMPERATURA DESIDE-
RATA IL VISORE TORNERÀ A INDICARE
LA TEMPERATURA AMBIENTE.
3.Premere il pulsante FAN per impostare la velocità ventilatore.
ONON ON
Δ1 H Δ1 H
MIN. MAX.
A
B
C
C
B
A
27
26
25
24
23
22
21
20
19
NOTE
Il climatizzatore cambia il modo di funzionamento (da freddo
a caldo o viceversa) al verificarsi di una delle seguenti
condizioni:
-ZONA A: cambia se la temperatura varia di almeno 3°C da
quella impostata sul telecomando.
-ZONA B: cambia se la temperatura varia di almeno 1°C da
quella impostata sul telecomando dopo un’ora dallo stop
del compressore.
- ZONA C: non cambia mai se la temperatura non varia più
di 1°C rispetto a quella impostata sul telecomando.
NOTA
TRASCORSI 5 SECONDI DALL’IMPOSTA-
ZIONE DELLA TEMPERATURA DESIDE-
RATA IL VISORE TORNERÀ A INDICARE
LA TEMPERATURA AMBIENTE.
IL VISORE INDICHERÀ IL VALORE
DELLA TEMPERATURA SELEZIONATA.
IL VISORE INDICHERÀ IL VALORE
DELLA TEMPERATURA SELEZIONATA.
TRASCORSI 5 SECONDI DALL’IMPOSTA-
ZIONE DELLA TEMPERATURA DESIDE-
RATA IL VISORE TORNERÀ A INDICARE
LA TEMPERATURA AMBIENTE.
RISCALDAMENTO
FUNZIONAMENTO IN AUTOMATICO
C
1
3
22
1
3742540582-USO-TEC-MPAF13A-B 20-07-2015 8:52 Pagina 6