Technibel PORTABLE SCDF32C5I User manual

37.4256.032.00 01/2019
Room air conditioner with remote condenser
Condizionatore d’ambiente con condensatore remoto
Climatiseur avec condenseur a air exterieur - Klimagerät mit außengerät
Acondicionador de ambiente con condensador a distancia
Ar Condicionado com condensador remoto
EN
IT
OPERATING INSTRUCTIONS
ISTRUZIONI D’USO
NOTICE D’UTILISATION
BEDIENUNGSANLEITUNG
INSTRUCCIONES DE USO
INSTRUCÇÕES DE FUNCIONAMENTO
FR
DE
ES
PT
PORTABLE SCDF32C5I

2
EN
CONTENTS
PRODUCT INFORMATION
If you have problems or questions concerning your Air
Conditioner, you will need the following information. Model
and serial numbers are on the nameplate on the bottom
of the air conditioner.
Model No..........................................................................
Serial No...........................................................................
Date of purchase..............................................................
Dealer’s address ..............................................................
Phone number ...................................
ALERT SYMBOLS
The following symbols used in this manual, alert you
to potentially dangerous conditions to users, service
personnel or the appliance:
This symbol refers to a hazard or unsafe practice which
can result in severe personal injury or death.
This symbol refers to a hazard or unsafe practice which can
result in personal injury or product or property damage.
WARNING
CAUTION
SAFETY INSTRUCTIONS
•Read this booklet carefully before using this
air conditioner. If you still have any difficulties
or problems, consult your dealer for help.
•Never use or store gasoline or other flammable vapour
or liquid near the air conditioner. It is very dangerous.
Moreover, never install electrical equipment, which
is not protected with IPX1 protection (protection
against vertical water drop), under the unit.
•The manufacturer assumes no responsibilities if the
safety regulations or local codes are not observed.
•Never use neither the power main switch or the
power plug to start or stop the air conditioner.
Always use the ON/OFF button.
•Do not stick anything into the air outlet of the air
conditioner. This is dangerous because the fan is
rotating at high speed.
•Do not let children play with the air conditioner.
•Do not cool the room too much if babies or invalids
are present.
•This air conditioner can be used by children aged
from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
air conditioner in a safe way and understand the
hazards involved.
•Cleaning and user maintenance shall not be made
by children without supervision.
•For safety, be sure to turn the air conditioner off and
also to disconnect the power before cleaning.
WARNING
CAUTION
•This air conditioner is designed to give you
comfortable room conditions for domestic use.
As far as industrial and professional activities
are concerned, the manufacturer declines all
responsibility for any unsuitability of the appliance
depending on its characteristics and the purposes it
should be responsible for.
SAFETY INSTRUCTIONS............................................................................... 2
INSTALLATION LOCATION............................................................................ 3
ELECTRICAL REQUIREMENTS .................................................................... 3
PRODUCT IDENTIFICATION.......................................................................... 4
MONITOR PANEL .......................................................................................... 4
AIR CONDITIONER INSTALLATION............................................................... 5
IMPORTANT ADVICE ..................................................................................... 5
USING THE REMOTE CONTROL UNIT ......................................................... 6
REMOTE CONTROL UNIT ............................................................................ 7
HOW TO SET THE PRESENT TIME .............................................................. 8
COOLING ....................................................................................................... 8
DEHUMIDIFYING (DRY) ................................................................................. 8
FAN ONLY...................................................................................................... 8
ADJUSTING THE FAN SPEED ....................................................................... 8
NIGHT MODE/ENERGY SAVING ................................................................... 8
HIGH POWER MODE..................................................................................... 9
SETTING THE TIMER..................................................................................... 9
SETTING 1 HR TIMER.................................................................................... 9
ADJUSTING THE AIR FLOW DIRECTION...................................................... 10
OPERATION WITHOUT THE REMOTE CONTROL UNIT............................... 10
CARE AND CLEANING................................................................................... 10
ACCESSORIES (SUPPLIED ON REQUEST) .................................................. 11
TIPS FOR ENERGY SAVING.......................................................................... 12
TROUBLESHOOTING .................................................................................... 12
MATCH BETWEEN REMOTE CONTROLLER AND THE UNIT....................... 13

3
EN
This air conditioner is equipped with cooling, drying and fan functions.
Details on these functions are provided here following; refer on these descriptions when using the air conditioner.
NOTE
COOLING
OUTDOOR TEMPERATURE 46°C D.B.
ROOM TEMPERATURE 32°C D.B./23°C W.B.
OUTDOOR TEMPERATURE 19°C D.B.
ROOM TEMPERATURE 19°C D.B./14°C W.B.
OPERATING LIMITS
MAXIMUM CONDITIONS
MINIMUM CONDITIONS
Before using the appliance
•Check that the power supply at the location where the
air conditioner is going to be used is 220/240 volt, single
phase.
•For your safety care check periodically the conditions
of the electric supply cable; the electrical connection of
the unit is Y type with cable prepared in a special way;
in case you should notice any damage due to usage, call
the nearest After Sale Service to get the cable replaced.
•Before connecting the air conditioner to a power
socket, make sure that the socket is provided with
an earth connection.
•Verify that the available power supply is sufficient for
running other electrical domestic appliances in use
simultaneously from the same supply. See the data
plate on the unit showing the max. absorbed powers.
•Install a double - pole switch, protected fuses of the
delayed type, upstream the electricity wall socket 10A.
ELECTRICAL REQUIREMENTSINSTALLATION LOCATION
•Do not install this air conditioner where there are
fumes or flammable gases, or in an extremely humid
space such as a green house.
•Do not install the air conditioner where excessively
high heat-generating objects are placed.
•Do not install the air conditioner where the
atmosphere is extremely damp or humid (e.g.
greenhouse or laundry) it could be wetted by drops
of water (i.e. in laundries).
Avoid:
To protect the air conditioner from heavy corrosion, avoid
installing the outdoor unit where salty sea water can
splash directly onto it or in sulphurous air near a spa.
•Make sure that there are no obstacles around the
indoor unit affecting the free circulation of air. Do
not block the air intake and outlet of the unit with
curtains or other.Never put objects on the top of
the unit.
WARNING
•Make sure that circuit breakers, fuses, etc. are of
sufficient capacity to handle start - up current (normally
for no longer than a second).
•All wiring must conform to the local electrical codes.
Consult your dealer or a qualified electrician for details.
WARNING!
The air conditioner is provided with a time-guard system,
which does not allow re-starting of compressor until after
3 minutes from a previous stop.

4
EN 01. Infrared rays remote control unit
02. Monitor panel
03. Supply air deflector
, 4. Return air grille
, 5. Outdoor unit
06. Flexible tube
07. Air filter
08. Electric cable with plug
09. Service tube for condensate evacuation
10. Outdoor unit basket or support
11. Quick coupling cover
MONITOR PANEL
1. TIMER lamp: This lamp lights up when the system is
being controlled by the timer.
2. OPERATION lamp: This lamp lights up during operation.
It blinks once to announce that the remote control signal
has been received and stored.
The OFF position does not disconnect the power. Use the
main power switch to turn off power completely.
WARNING
This lamp flashes and the air conditioner simultaneously
stops during exceeding condensate drainage or because
of malfunctioning of the condensate drainage system.
WATER-LEVEL ALARM
5. Operation button (without remote control): Push the
button to walk through the OFF and COOL operation
modes.
PRODUCT IDENTIFICATION
10
2
7
11
5
6
1
8
3
49
1
5
243
3. STANDBY lamp: this lamp lights up when the air
conditioner is connected to the power and ready to
receive the remote control command.
4. Receiver : receives signals transmitted from the remote
control.
NOTE
The fixed OPERATION lamp and the blinking of TIMER and
STANDBY lamps, indicates that the operating mode selected
( ) is not compatible with the unit. If this happen the
air conditioner does not operate until the correct mode is
selected.

5
EN
POSITIONING OF OUTDOOR UNIT
The outdoor unit must always be kept in vertical position and
levelled. Make sure that there are no obstacles around the unit
affecting the free circulation of air. A lug at the rear bottom
of the unit ensures the minimum distance from the wall (3
cm). The unit must be kept at a minimum distance of cm. 15
(sidewise) and cm. 80 (frontally) from any walls.
INSTALLATION TYPE A
If your room has a balcony or a window-sill of sufficient depth
(min. 25 cm) you may rest the unit freely onto it. For safety’s
sake, you may anchor the unit to the window-sill using one M6
x 20 expansion bolt in the slot of the lug at the rear bottom
of the unit.
The flexible tube may easily pass through the balcony door
or window shutters set ajar.
INSTALLATION TYPE B (USING THE SUPPORT)
1. Fix the support guide to the wall below the window sill.
2. Insert the support in the handle of outdoor unit, and turn
the outdoor unit upside down as shown in the picture.
3. Place the support and secure it at the edge of the unit,
using the screws.
4. Insert the support, fixed on the unit, at the guide fixed to
the wall. Make sure it is levelled.
SUPPORT
2 holes ø 10
support
guide
100 min.
200
140
The air conditioner is made of two units interconnected by a
flexible tube. The indoor unit must be placed in the room to be
air conditioned, near a window, a balcony-door or a perimeter
wall. The outdoor unit, that provides to the disposal of heat
and condensation, must be located outside, on a window sill,
on a balcony or hanged to the wall.
Min. 25 cm.
M6 x 20
M6 x 20
AIR CONDITIONER INSTALLATION
TYPE A
TYPE B
IMPORTANT ADVICE
OUTDOOR UNIT
1.When you move the outdoor unit, always hold it by the handle, never pull it by the flexible tube.
2.Never let the outdoor unit hang on the flexible tube.
3.When you recover the outdoor unit after operation, drain away any remaining condensate by tilting the unit.
NO!
NO!

6
EN
OPERATION WITH THE REMOTE CONTROL UNIT
When using the remote control unit, always point the unit
transmitter head directly at the air conditioner receiver.
TEMPERATURE SENSOR SELECTOR
•Under normal conditions the room temperature is
detected and checked by the temperature sensor placed
in the remote controller (I FEEL icon displayed ).This
function is designed to provide a comfortable room
temperature by transmitting the temperature control
command from the location next to you. When using this
function, the remote, control should always be pointed
at the air conditioner, therefore it should be placed in
a position in which it is visible by the indoor unit (for
example, do not put it in a drawer).
lIt is possible to disable the remote controller room
sensor pressing the I FEEL button. In this case the I
FEEL icon on the remote controller display lights off and
the sensor placed in the air conditioner becomes active.
USING THE REMOTE CONTROL UNIT
INDOOR UNIT
REMOTE CONTROL UNIT
RECEIVER
TRANSMITTER HEAD
• InserttwoAAAalkalinebatteriesof1,5V-DCmaking
sure that point in the direction marked in the battery
compartment.The displayed time flashes.
Press the SEL TYPE button.
Remote controller is now ready for operation.
• Thebatterieslastaboutsixmonths.Dependingonhow
much you use the remote control unit.
Remove the batteries if you do not use the remote
control unit for more than one month.
Replace the batteries when the remote control unit
lamp fails to light, or when the air conditioner does not
receive the remote control unit signals.
• Thebatteriesoftheremotecontrolcontainpolluted
substances exhausted batteries must be disposed
according to the laws in force.
HOW TO REMOVE BATTERIES
•Remove the lid.
•Press the battery
toward the
negative end
and lift it out by
its positive end
(as shown in the
figure).
•Remove the other
battery in the same
way.
HOW TO INSTALL BATTERIES
•Remove trhe lid in the rear part of the remote control
unit and check the settings of the microswitches as
shown below:
SWITCHES
The remote control unit transmits signals to the
indoor unit each time you press a key and at any
temperature change detected by the IFEEL sensor. In
case of troubles (low batteries, remote control placed
in a position not visible by the indoor unit,...) room
temperature control is automatically switched to the
sensor of the indoor unit. In this case, the temperature
around the remote control unit may differ from the
temperature detected in the air conditioner position.
NOTE

7
EN
REMOTE CONTROL UNIT
DISPLAY
Information is displayed when the remote controller is switched
on. If switched off, only the operating mode, the room temperature
and the clock are shown
Operation mode
Fan speed
High speed
Automatic Medium speed
Low speed
Displayed when
transmitting data
Set point
temperature
I FEEL mode is active
(remote controller
sensor active)
Timer modes
Automatic
Cooling
Dehumidification
Fan
C
Clock
Room
temperature
Night
mode
HIGH POWER
mode
TRANSMITTER
When you press
the buttons of the
remote control unit,
the mark
appears on the
display to transmit
the setting changes
to the receiver in the
air conditioner.
HOURS AND MINUTES SETTING
BUTTONS
With these buttons is possible to set the
clock and the timer. For details refer to
paragraphs “ SETTING THE HOUR” and
“SETTING THE TIMER”.
TIMER SELECTION BUTTON
Press this button to select the type of
timer to activate. For details refer to
paragraph “SETTING THE TIMER”.
C
TEMPERATURE SETTING BUTTONS
- (cooler)
Press this button to decrease the set
temperature.
+ (warmer)
Press this button to increase the set
temperature.
SENSOR
A temperature
sensor inside the
remote control unit
detects the room
temperature.
CLOK AND TIMER SETTING BUTTON
Press this button in order to:
•settheclock
•settheON/OFFtimer
For details refer to paragraphs “SETTING
THE HOUR” and “SETTING THE TIMER”.
IFEEL/IFEEL C SENSOR SELECTOR
Press this button to modify the active
setting for room temperature detection
(from remote controller to air conditioner
and viceversa).
“FAN “ BUTTON (fan speed)
Fan speed is automatically
selected by the
microcomputer.
High speed.
Medium speed.
Low speed.
ON/OFF BUTTON
This button turns the air conditioner ON
and OFF.
INACTIVE BUTTON
NIGHT/ECO BUTTON
Press this button in order to select the
NIGHT/ECO mode.
INACTIVE BUTTONS
“HIGH POWER” BUTTON
Press this button in order to select the
HIGH POWER mode.
MODE SELECTOR BUTTON
Press this button to modify the air
conditioner mode.
(cooling)
(automatic)
The air conditioner makes the room
cooler.
(dry)
The air conditioner reduces the humidity
in the room.
(fan)
The air conditioner works only as a
circulation fan.
Inverter model
NOT AVAILABLE OPERATION MODE

8
EN
ADJUSTING THE FAN SPEED
HOW TO SET THE PRESENT TIME
COOLING / AUTOMATIC
DEHUMIDIFYING (DRY)
2. Press the SET H button until the present time hour is
displayed.
Press the SET M button until the present time minutes
are displayed. The display will automatically stop
flashing.
1. Press the button SEL TYPE three times.
The time indication alone flashes.
FAN ONLY
Verify that the unit is connected to the
main power and the STANDBY lamp is
light up.
1.Set the selector to COOL (symbol
on the display).
2.Press the +/- buttons (temperature
selection) to set the desired temperature
(the temperature range is between 32 °C
max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
3.Press the FAN button to select the fan speed.
NOTE
C
1
3
22
1
1.Set the button to DRY. The icon is displayed.
2.Press the +/- buttons (temperature selection) to set the
desired temperature (the temperature range is between
32 °C max. and 10 °C min.).
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE SETTING
THE DISPLAY WILL SHOW THE ROOM
TEMPERATURE AGAIN.
•Use DRY operation when you want to reduce the humidity
in the room.
•Once the room temperature reaches the set level, the unit
repeats the cycle of turning on and off automatically.
•During DRY operation, the fan speed is automatically
set (Remote control lamp is ON) to prevent
overcooling.
•Dry operation is not possible if the indoor temperature is
10 °C or less.
NOTE
If you want to make air circulate without any temperature
control, press button until only the fan symbol
appears on the display.
AUTOMATIC
Simply set the FAN selector to the position.A
microcomputer automatically controls the fan speed when
the AUTO mode is selected. When the air conditioner
starts operating, the fan speed varies (high - medium -
low - very low) according to the thermal load of the room.
The automatic speed is not available in FAN ONLY mode.
NOTE
MANUAL
If you want to manually adjust speed just set the FAN
selector as desired.
High speed Med. speed Low speed
NIGHT MODE / ENERGY SAVING
lThis mode enables you to save energy.
1. Set the selector to cool or dry.
2. Press the button.
3. The mark appears on the display. Press the
button again to release the function.
What does the NIGHT mode mean?
When you select the NIGHT mode, the air conditioner will
modify automatically the set temperature after 60 minutes:
it will be raised by 1°C.
This enables you to save energy without sacrificing your
comfort.
During the NIGHT mode the internal fan speed is
automatically lowered and reduces the noise.
NOTA

9
EN
A) HOW TO SET THE ON TIME
1. Press the ST button once.
The ON and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display
will change automatically back to
show the present time after 10 sec.
3. Press the ON/OFF button to start the
air conditioner.
4. Press the button to activate the
ON timer.
B) HOW TO SET THE OFF TIME
1. Press the ST button twice.
The OFF and time indications flash.
2. Press the H button until the designed
hour is displayed.
Press the M button until the designed
minutes are displayed. The display will
change automatically back to show
the present time after 10 sec.
3. Press the ON/OFF button to start the
air conditioner.
4. Press the button two times to
activate the OFF timer.
C) HOW TO SET A PROGRAM FOR
DAILY ON/OFF OPERATION (OR
VICEVERSA)
1. Set the timer ON/OFF as shown in A)
and B).
2. Press the ON/OFF button to start the
air conditioner.
3. Press three times the button to
activate the DAILY timer.
SETTING THE TIMER
After timer setting, press ST button in order to check the
ON/OFF setting time.
NOTE
C
4
2
2
3
1
HIGH POWER MODE
You can select High Power only during cooling mode and
not during dehumidifying (dry) and fan mode. High Power
mode allows to obtain the maximum air conditioner’s
efficiency. The user can choose to activate the High
Power mode, using the remote control unit, after having
selected cooling mode. Under these conditions the air
conditioner will reach its maximum thermal power and
consequently also the maximum electrical consumption
and noise. On the contrary, if you want to obtain the best
performance in efficiency and silentness, High Power
mode is not recommended: let the air conditioner run in
normal condition (factory default program).
To activate High Power mode it is necessary (after having
selected the cooling mode) to press the HIGH POWER
button : the symbol switches on; at this point
the operation lamp (green lamp on the front panel of the
air conditioner) begins blinking slowly, indicating that High
Power mode is activated; press the button again to release
the function: therefore the green lamp will stop blinking
and it will be switched on permanently.
NOTES
•During the high power operation the room temperature
could not correspond to the set temperature.
•HIGH POWER program remains set also if you switch
OFF and ON again the air conditioner.
TIMER SETTING PROCEDURE.
•Press four times the button.The 1
HOUR TIMER mark will appear on the
display.
CANCELLATION PROCEDURE
•Press the ON/OFF button to turn the air conditioner off.
•Wait for the indoor unit to stop operating.
•Press the ON/OFF button again to turn the air conditioner
on.
SETTING THE 1 HOUR TIMER
This function causes the unit to operate for one hour at the
set conditions, regardless of whether the unit is on or off.

10
EN
•Do not pour water on the unit to clean it. This will damage
the internal components and cause an electric shock
hazard.
•Never use solvents, or chemical agents when cleaning
the indoor unit. Do not wipe the plastic casing using very
hot water.
Casing and Grille
Clean the casing and grille of the indoor unit with a vacuum
cleaner brush, or wipe them with a clean, soft cloth. If
these parts are stained, use a clean cloth moistened with
a mild liquid detergent. When cleaning the grille, be careful
not to force the blades out of place.
HORIZONTAL
The horizontal air flow can be adjusted by moving the
vertical blades to the left or right, as indicated in the
following figure.
ADJUSTING THE AIR FLOW DIRECTION
Set vertical blades to the front position during
COOLING/DRY operation if humidity is high.
If the vertical blades are set to the left-most or right-
most position, condensation will form around the air
outlet and drip off.
CAUTION
VERTICAL
Hold the end of the flap and move it up and down to adjust
the vertical air flow.
2. WHEN THE AIR CONDITIONER IS RUNNING
If you want to turn off the air conditioner push the
OPERATION BUTTON until the OPERATION lamp is
turned off.
Power failure during operation.
In the event of power failure, the unit will stop. When the
power is resumed, the unit automatically restarts after 3
minutes.
NOTE
If you have lost the remote control unit or it has troubles,
follow the steps below.
1. WHEN THE AIR CONDITIONER IS STOPPED
If you want to turn on the air conditioner push the
OPERATION BUTTON to select the COOL mode:
OPERATION WITHOUT THE REMOTE
CONTROL UNIT
The air conditioner will start in HIGH fan speed.
The temperature setting is 25°C.
NOTE
CARE AND CLEANING
For safety, be sure to turn the air conditioner off and
also to disconnect the power before cleaning.
•Some metal edges and the
condenser fins are sharp and may
cause injury if handled improperly;
special care should be taken when
you clean these parts.
•Periodically check the outdoor unit
to see if the air outlet or air intake
are clogged up with dirt or soot.
•The condenser and other
components of the outdoor unit
must be cleaned periodically.
Consult your DEALER or AFTER
SALES SERVICE.
OUTDOOR UNIT
(CASING AND CONDENSING COIL)
CAUTION
INDOOR UNIT
TEST
OFF ON
OPERATION BUTTON

11
EN
AIR FILTER
The air filter must be cheked at least once every two weeks
operation. Operation with a dirty filter always causes a lower
efficency of the air conditioner and severe product damage.
The filter is located at the back of the intake grille in the front
of the air-conditioner and shall be removed from the upper
side of the unit.
HOW TO REMOVE THE FILTER
FILTER CLEANING
Use a vacuum cleaner to remove light dust. If there is
sticky dust on the filter, wash the filter in lukewarm,
soapy water, rinse it in clean water, and dry it.
TRANSPORT
Preferably keep the air conditioner in the vertical position
during transportation. If this is not possible, then lay it on
one side; when at destination put the air conditioner back
in the vertical position and wait at least 10 minutes before
using it.
STORAGE
If you are not going to use the air-conditioner for a long
period, clean the air filters, evacuate the condensate from
the indoor unit through the drain hose at the unit back
side. Do not disconnect the flexible tube, unless you are
obliged to do it: in that case protect the open halves of the
couplings with the plugs supplied as accessories, that must
be tightened with a spanner. Do not put heavy objects on the
top of the unit, and protect it with a cloth or a plastic bag.
CONDENSATE DRAIN PIPE
ACCESSORIES (SUPPLIED ON
REQUEST)
SUPPLEMENTARY SUPPORT GUIDE KIT FOR
OUTDOOR UNIT
2 holes ø 10
100 min.
200
SUPPORT GUIDE
If you want to utilise the air conditioner in several rooms, it
is possible to buy varies support guides for the installation
of outdoor unit.

12
EN
•The use of portable telephones near the air-conditioner
may cause disturbance to its normal operation and
must be avoided. In case abnormal operation is noticed,
(OPERATION lamp lights but outdoor unit will not run)
to restore normal operation turn-off electric supply for
60 seconds at least, by disconnecting the main switch
or the wall plug, then start again the air-conditioner.
•The blinking OPERATION lamp, together with the stop
of the air conditioner for a short time are due to the
exceeding condensate drainage.
If the OPERATION lamp goes on blinking and the air
conditioner definitely stops means that the condensate
pump is not working or that the condensate drain pipe
in the flexible connection pipe is obstructed; in this case
contact the AFTER SALE SERVICE.
In case of emergency the air conditioner can work by
draining the condensate from the back little pipe into a
rather short container: extract the little pipe and remove
the cap.
•If your air conditioner does not work properly, first check
the following points before requesting service.
If it still does not work properly, contact your dealer or
service center.
TIPS FOR ENERGY SAVING
DO NOT:
lBlock the air intake and outlet of the unit.
If they are obstructed, the unit will not work well, and
may be damaged.
lLet direct sunlight into the room. Use sunshades, blind
or curtain.
DO:
lAlways try to keep the air filter clean. A clogged filter
will impair the performance of the unit.
lTo prevent conditioned air from escaping, keep
windows, doors and any other openings closed.
TROUBLESHOOTING
Trouble: the air conditioner does not run at all.
Possible cause:
1. Power failure.
2. Leakage breaker tripped.
3. Line voltage is too low.
4. Operation button is OFF.
5. Batteries in remote control unit have run down.
Remedy:
1. Restore power.
2. Contact service center.
3. Consult your electrician or dealer.
4. Press the button again.
5. Replace batteries.
Trouble: Compressor runs but soon stops.
Possible cause:
1. Obstruction in front of condenser coil.
Remedy:
1. Remove obstruction.
Trouble: Poor cooling performance.
Possible cause:
1. Dirty or clogged air filter.
2. Heat source or many people in room.
3. Doors and/or windows are open.
4. Obstacle near air intake or air discharge port.
5. Thermostat is set too high.
Remedy:
1. Clean air filter to improve airflow.
2. Eliminate heat source if possible.
3. Shut them to keep the heat or cold out.
4. Remove it to ensure good airflow.
5. Set the temperature lower.
Trouble: Clicking sound is heard from the air conditioner.
Possible cause:
1. Any plastic parts may expand or shrink due to a sudden
temperature change. In this event, a clicking sound may
occur.
Remedy:
1. This is normal, and the sound will disappear when an
even temperature is settled.
NOTE
The fixed OPERATION lamp and the blinking of TIMER and
STANDBY lamps, indicates that the operating mode selected
( ) is not compatible with the unit. If this happen the
air conditioner does not operate until the correct mode is
selected.
LEDS POSSIBLE CAUSE REMEDY
STANDBY OPERATION TIMER
F F O Defective indoor air sensor Contact service centre
O F F Defective indoor air coil sensor Contact service centre
F O O Defective compressor discharge temperature sensor Contact service centre
F•OMulfunctioning of electronic PCB (current protection) Contact service centre
F O •Mulfunctioning of electronic PCB (temperature protection) Contact service centre
F• • Mulfunctioning of PFC (power factor correction system) Contact service centre
O F O Mulfunctioning of the condensate drainage system Contact service centre
AUTO-DIAGNOSIS
O = LED OFF
•= LED ON
F = Flashing LED

13
EN
1
FACTORY STATE
1=OFF 2=OFF 3= OFF 4=OFF
5=ON 6=ON
JP2=CLOSE JP3=CLOSE
2
1=ON 2=OFF 3=OFF 4=OFF
5=ON 6=ON
JP2=OPEN JP3=CLOSE
3
1=OFF 2=ON 3=OFF 4=OFF
5=ON 6=ON
JP2=CLOSE JP3=OPEN
4
1=ON 2=ON 3=OFF 4=OFF
5=ON 6=ON
JP2=OPEN JP3=OPEN
REMOTE CONTROL UNIT PCB
UNIT
Set JP2 and JP3 as shown in the table.
Proceed as follows:
•Disconnect the power of the unit.
•Remove the batteries from the remote control unit.
•Set the microswitches (see table).
•Insert the batteries in the remote control unit.
•Switch on the unit.
At this point the unit starts operating with the new address.
MATCH BETWEEN REMOTE CONTROLLER AND THE UNIT
The remote control can be addressed for 4 different units installed in open space or similar:
-you can get unified control with only one remote control up to 4 units
or
-each remote control is addressed to its unit, so that it can control separately the temperature, the timer and all the
other functions.

14
EN INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE 2012/19/EU
At the end of its working life this equipment must not be disposed of as an household waste.
It must be taken to special local community waste collection centres or to a dealer providing this service.
Disposing of an electrical and electronic equipment separately avoids possible negative effects on the environment
and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled
to obtain significant savings in energy and resources.
In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.
INFORMATION FOR CORRECT DISPOSAL OF THE BATTERY IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE 2006/66/EC
Please replace battery when its electricity charge is used up: please do not eliminate this battery together with normal
household waste. It must be taken to special local community waste collection centres or to a dealer providing this
service. Disposing of a battery separately avoids possible negative effects on the environment and human health
deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant
savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the battery
is marked with a crossed-out dustbin.
REGULATION (EU) No. 517/2014 - F-GAS
The unit contains R32, a fluorinated greenhouse gas with a global warming potential (GWP) of 675.
Do not release R32 into the atmosphere.

15
EN

2
IT
INDICE
ISTRUZIONI DI SICUREZZA .......................................................................... 2
LUOGO DI INSTALLAZIONE.......................................................................... 3
REQUISITI ELETTRICI ................................................................................... 3
IL PRODOTTO................................................................................................ 4
PANNELLO SEGNALAZIONI ......................................................................... 4
INSTALLAZIONE DEL CLIMATIZZATORE ..................................................... 5
AVVERTENZE IMPORTANTI .......................................................................... 5
USO DEL TELECOMANDO............................................................................ 6
TELECOMANDO ........................................................................................... 7
COME REGOLARE L’OROLOGIO ................................................................. 8
RAFFREDDAMENTO...................................................................................... 8
DEUMIDIFICAZIONE ...................................................................................... 8
VENTILAZIONE............................................................................................... 8
SCELTA VELOCITÀ’ VENTILATORE .............................................................. 8
PROGRAMMA NOTTURNO/RISPARMIO ENERGIA...................................... 8
PROGRAMMA HIGH POWER........................................................................ 9
REGOLAZIONE DEL TIMER........................................................................... 9
REGOLAZIONE DEL TIMER 1 ORA............................................................... 9
REGOLAZIONE DEL FLUSSO D’ARIA ........................................................... 10
FUNZIONAMENTO SENZA TELECOMANDO................................................ 10
MANUTENZIONE E CURA ............................................................................. 10
ACCESSORI (FORNITI SU RICHIESTA)......................................................... 11
CONSIGLI PER IL MASSIMO COMFORT ED IL MINIMO CONSUMO .......... 12
IDENTIFICAZIONE E SOLUZIONE PROBLEMI DI FUNZIONAMENTO.......... 12
ABBINAMENTO TRA TELECOMANDO E UNITA’.......................................... 13
INFORMAZIONI RIGUARDANTI IL PRODOTTO
In caso di difficoltà o se si hanno dei dubbi riguardo
al condizionatore d’aria, sono necessarie le seguenti
informazioni. I numeri del modello e quelli di serie si
trovano sulla targhetta del nome, sul climatizzatore.
No. del modello ...............................................................
No. di serie ......................................................................
Data di acquisto ..............................................................
Indirizzo del rivenditore ...................................................
Numero di telefono ...........................
SIMBOLI DI AVVERTIMENTO
I seguenti simboli sono usati in questo manuale per
mettere in guardia l’utente ed il personale di servizio sulle
condizioni potenziali di pericoli personali o di danni al
prodotto.
Questo simbolo si riferisce a pericoli o a interventi che
possono causare ferite gravi o la morte.
Questo simbolo si riferisce a pericoli o a interventi che
possono causare danni al prodotto.
AVVERTIMENTO
PRECAUZIONE
ISTRUZIONI DI SICUREZZA
•Mai usare o conservare benzina o altri liquidi infiammabili
vicino al condizionatore. E’ molto pericoloso.
Inoltre, non installare sotto l’unità, apparecchiature
elettriche non protette con grado di protezione IPX1
(protezione all’acqua a caduta verticale).
•Il costruttore non si assume responsabilità alcuna nel
caso in cui le norme di sicurezza e antinfortunistiche non
vengano rispettate.
•Leggete attentamente questo manuale prima
di usare il condizionatore d’aria. In caso di
dubbi o problemi, rivolgetevi al rivenditore o
centro assistenza autorizzato.
AVVERTIMENTO
•Non usare mai né l’interruttore generale né la spina
come mezzo per arrestare o avviare il climatizzatore
Usate sempre il tasto di accensione/spegnimento
(ON/OFF).
•Non inserite oggetti nel condizionatore. E’ molto
pericoloso perché il ventilatore gira ad alta velocità.
•Non lasciate giocare i bambini con il condizionatore
d’aria.
•Non raffreddate eccessivamente la stanza se ci sono
bambini molto piccoli o degli invalidi.
•Questo condizionatore può essere usato da bambini
dagli 8 anni in su e da persone con ridotte capacità
fisiche, sensoriali o mentali, oppure con mancanza
di esperienza o di conoscenza, se hanno potuto
beneficiare, attraverso l’intermediazione di una
persona responsabile della loro sicurezza, di una
sorveglianza o di istruzioni riguardanti l’uso del
condizionatore e quindi hanno capito i possibili
rischi.
•La pulizia e la manutenzione dell’utente non devono
essere eseguite dai bambini senza supervisione.
•Prima di procedere ad operazioni di pulizia e
manutenzione, spegnere il condizionatore, quindi
togliere la spina dalla presa di corrente.
PRECAUZIONE
•Questo condizionatore d’aria è stato progettato
per creare condizioni climatiche ideali ad uso
domestico. Per quanto concerne le attività di
carattere industriale e professionale il produttore
declina ogni responsabilità per l’eventuale
inidoneità dell’apparecchio in dipendenza delle sue
caratteristiche e delle finalità cui dovrebbe essere
preposto.

3
IT
ATTENZIONE!
Il climatizzatore è dotato di un sistema di protezione
del compressore dai sovraccarichi che non consente la
partenza del compressore se non sono trascorsi almeno
3 minuti da un precedente arresto.
RAFFREDDAMENTO
TEMPERATURA ESTERNA 46°C B.S.
TEMPERATURA INTERNA 32°C B.S./23°C B.U.
TEMPERATURA ESTERNA 19°C B.S.
TEMPERATURA INTERNA 19°C B.S./14°C B.U.
Questo condizionatore d’aria è dotato delle funzioni di raffreddamento, deumidificazione e ventilazione.
I dettagli su queste funzioni sono forniti di seguito; riferitevi a queste descrizioni quando usate il condizionatore d’aria.
NOTA
CONDIZIONI MASSIME
CONDIZIONI MINIME
LIMITI DI FUNZIONAMENTO
•Assicuratevi che interruttori automatici e valori di
protezione dell’impianto siano in grado di sopportare la
corrente di spunto (normalmente per un tempo inferiore
a 1 secondo).
•Tutti gli allacciamenti elettrici devono essere conformi
alle normative elettriche locali. Per i dettagli, consultare
il rivenditore o un elettricista.
LUOGO DI INSTALLAZIONE
•Non installare questo condizionatore d’aria dove ci
sono fumi, gas infiammabili o molta umidità, come
in una serra.
•Non installare il condizionatore dove ci sono
apparecchiature che generano un calore eccessivo.
•Non installare l’unità interna in locali dove potrebbe
essere investita da spruzzi d’acqua (es. lavanderia).
Evitare:
Per proteggere il condizionatore d’aria dalla corrosione
eccessiva, non installate l’unità esterna dove può essere
esposta direttamente agli spruzzi d’acqua marina o a
vapori solforosi nelle stazioni climatiche.
•Assicurare la libera circolazione dell’aria all’unità
interna. Non ostruire con tendaggi o simili la griglia di
aspirazione e quella di mandata. La parte superiore
deve essere libera da qualsiasi ostacolo, non
depositare oggetti sul climatizzatore.
AVVERTIMENTO
Prima di usare il climatizzatore
•Verificate che la tensione nominale monofase di
alimentazione nel luogo di utilizzo sia di 220/240 Volt.
•Per la vostra sicurezza abbiate cura di verificare
periodicamente lo stato del cavo di alimentazione; il
collegamento elettrico dell’unità é di tipo Y con cavo
preparato in modo speciale; qualora fosse danneggiato
dall’uso, per la sostituzione, rivolgersi al Centro
Assistenza.
•Assicuratevi che la presa dell’impianto elettrico sia
sempre provvista di messa a terra efficiente.
•Assicuratevi che l’impianto elettrico sia in grado
di erogare la corrente d’esercizio necessaria per il
climatizzatore oltre a quella assorbita normalmente da
altre utenze (elettrodomestici, illuminazione). Vedere gli
assorbimenti massimi indicati sulla targhetta dati posta
sull’apparecchio.
•Installare un interruttore bipolare, con fusibile di
protezione del tipo ritardato, a monte della presa
d’alimentazione di 10A.
REQUISITI ELETTRICI

4
IT
PANNELLO SEGNALAZIONI
1. Spia TIMER: si accende quando l’unità è controllata
dal timer.
2. Spia funzionamento (OPERATION): si accende
quando l’unità è in funzione. Lampeggia una volta
per avvisare che il segnale del telecomando é stato
ricevuto e memorizzato.
IL PRODOTTO
Lampeggia con il contemporaneo arresto del
condizionatore durante lo scarico della condensa in
eccesso, oppure per il malfunzionamento dello stesso
sistema di evacuazione condensa.
ALLARME LIVELLO ACQUA
5. Tasto funzionamento (senza telecomando): Premere
questo tasto per passare da una funzione all’altra (OFF
e COOL).
01. Telecomando a raggi infrarossi
02. Pannello segnalazioni
03. Deflettore mandata aria
, 4. Griglia aspirazione aria
, 5. Unità esterna
06. Tubo flessibile
07. Filtro aria
08. Cavo eletttrico con spina
09. Tubetto servizio scarico condensa
10. Contenitore o supporto unità esterna
11. Coperchio attacchi rapidi
3. Spia attesa (STANDBY): Si accende quando il
condizionatore é collegato alla rete elettrica ed é pronto
a ricevere il segnale dal telecomando.
4. Ricevitore: riceve i segnali inviati dal telecomando.
La posizione OFF non interrompe l’alimentazione elettrica.
Usate l’interruttore principale per isolare il condizionatore
d’aria.
AVVERTIMENTO
NOTA
La spia OPERATION fissa e il lampeggio contemporaneo delle
spie TIMER e STANDBY, indica che il modo di funzionamento
selezionato ( ) non é compatibile con l’unità in oggetto.
Se ciò accade il condizionatore non funziona fino al ripristino
della modalità corretta.
10
2
7
11
5
6
1
8
3
49
1
5
243

5
IT
POSIZIONAMENTO UNITÀ ESTERNA
L’unità esterna deve sempre essere mantenuta in posizione
verticale e ben livellata. Assicurarsi che non vi siano ostacoli
alla libera circolazione dell’aria. Un piedino sporgente sul retro
dell’unità garantisce la minima distanza dalla parete (3 cm).
Garantire una distanza minima da eventuali pareti di cm. 15
sui lati e cm. 80 sul fronte dell’unità.
INSTALLAZIONE TIPO A
Se disponete di un balcone, oppure di una finestra con
davanzale abbastanza profondo (min. 25 cm) potete
appoggiare l’unità esterna liberamente. Per maggiore
sicurezza consigliamo di fissare il piedino posteriore dell’unità
al davanzale con un tassello ad espansione M6 x 20.
Il tubo flessibile potrà passare facilmente tra i battenti
accostati della finestra o porta-balcone, bloccati in posizione
di minima apertura.
INSTALLAZIONE TIPO B (CON SUPPORTO)
1. Fissare la guida supporto al muro sotto il davanzale della
finestra.
2. Inserire il supporto nella maniglia dell’unità esterna e
capovolgere quest’ultima come da figura.
3. Posizionare il supporto e fissarlo al bordo dell’unità
esterna con le viti.
4. Inserire il supporto fissato all’unità esterna nella
guida fissata al muro. Verificare che sia a livello.
SUPPORTO
2 fori ø 10
guida
supporto
100 min.
200
140
Il climatizzatore è composto da due unità collegate tra di loro
da un tubo flessibile. L’unità interna va collocata nel locale da
condizionare, in prossimità di una finestra, porta-balcone o
parete esterna. L’unità esterna, che assicura lo smaltimento
del calore e della condensa, va collocata all’esterno, sul
davanzale della finestra, sul balcone o appesa al muro.
Min. 25 cm.
M6 x 20
M6 x 20
INSTALLAZIONE DEL CLIMATIZZATORE
TIPO A
TIPO B
UNITÀ ESTERNA
1.Per spostare l’unità esterna, afferratela sempre per la maniglia, mai per il tubo flessibile.
2.Non lasciate mai penzolare l’unità esterna dalla finestra, appesa al tubo flessibile.
3.Quando ritirate l’unità esterna dopo il funzionamento, scaricate l’eventuale condensa residua inclinando l’unità.
NO!
AVVERTENZE IMPORTANTI
NO!

6
IT
UNITÀ INTERNA
TELECOMANDO
RICEVITORE
TESTINA DEL TRASMETTITORE
FUNZIONAMENTO CON IL TELECOMANDO
Indirizzare il telecomando con la testina del trasmettitore
verso il ricevitore posto sul condizionatore d’aria.
SELETTORE DEL SENSORE DI TEMPERATURA
• In condizioni normali la temperatura ambiente viene rilevata
e controllata dal sensore di temperatura posizionato
all’interno del telecomando (icona IFEEL attiva sul display).
Questa funzione permette di creare una temperatura
ambiente ottimale perché il telecomando trasmette la
temperatura dalla posizione in cui vi trovate. Usando
questa funzione, il telecomando deve sempre essere
indirizzato verso il condizionatore, quindi è opportuno che
si trovi in una posizione di visibilità rispetto all’unità interna
(ad esempio non metterlo in un cassetto).
•E’ possibile disattivare il sensore di temperatura del
telecomando premendo il tasto I FEEL. In tal caso la
relativa icona sul display si spegne e diventa operativo
il sensore presente all’interno dell’unità.
•Inserireduebatterieda1,5V-DCtipoAAAalcaline
rispettando la polarità indicata sul telecomando.
L’indicazione dell’ora sul display lampeggia.
Premere il tasto SEL TYPE.
Il telecomando ora é pronto per funzionare.
•Laduratamediadellebatterieèdiseimesiedipende
dalla frequenza con cui si usa il telecomando.
Rimuovere le batterie nel caso di lungo inutilizzo del
telecomando (oltre un mese).
Sostituire le batterie quando la spia di trasmissione
dati del telecomando non lampeggia oppure quando
il condizionatore non risponde ai comandi del
telecomando.
•Lebatteriedeltelecomandocontengonosostanze
inquinanti. Terminata la loro vita utile, devono essere
smaltite secondo le vigenti normative.
USO DEL TELECOMANDO
COME RIMUOVERE LE BATTERIE
•Rimuovere il coperchio.
•Premere la
batteria verso il
polo negativo ed
estrarla dalla parte
del polo positivo
(come mostrato in
figura).
•Rimuovere l’altra
batteria allo stesso
modo.
INSERIMENTO DELLE BATTERIE
•Rimuovere il coperchio sul retro del telecomando e
verificare che i microinterruttori siano impostati come
in figura:
INTERRUTTORI
Il telecomando trasmette segnali all’unità interna ogni
volta che si preme un tasto e ad ogni variazione della
temperatura rilevata dal sensore IFEEL.
In caso di inconvenienti (batterie scariche,
telecomando posizionato in area non visibile dall’unità
interna,...), il controllo della temperatura ambiente
viene automaticamente commutato sul sensore
dell’unità interna. In questi casi la temperatura vicino
al telecomando può differire dalla temperatura rilevata
nella posizione del condizionatore d’aria.
NOTA