TECshow FRESNELED 3100 MKII User manual

PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE /
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR
USER MANUAL / MANUAL DE USUARIO
FRESNELED
MKII

FRESNELED MKII
P.
2
1. OVERVIEW
Fresneled 3100 MKII is a fresnel LED luminaire powered
by 31 x 10W White LEDs that works at 3100K and exceeds
the brightness of traditional 2000W halogen fixtures, with a
90Ra color rendering. Equipped with a motorized zoom that
allows a beam angle variation from 15º to 60º, the fixture
adds great versatility to any fresnel application. Fresneled
3100 MKII sports long-life LEDs with a very low heat gener-
ation and power consumption, essential attributes for both
theater and broadcasting. Finally, the fixture has a 16-bit
dimmer with four dimming curves, strobe effect and motor-
ized focus, besides ensuring flicker free operation thanks to
its refresh rate.
SPECIFICATIONS
Source & Optic
• Light Source: 32 x 10W LEDs
• Color temperature: 3100K
• LEDs life: 50,000 hours
• Zoom: 15º-60º linear zoom
• Refresh rate: 600 Hz
Photometric Data
• Luminous Flux: 8400 Lm
• Peak intensity: 82091 cd
• Color rendering: >90Ra
• Flux: 15º: 2277 Lux @ 19 ft.
• 60º: 251 Lux @ 19 ft.
Effects & Functions
• Dimmer: Full range 0-100% (16-bit)
• 4 dimming curves
• Motorized focus
• Strobe effect: 0-20 flashes per second
• 15º-60º Electronic zoom
• Flicker free
Control
• DMX channels: 1/2/5
• Operational modes: DMX, Static, Master/Slave
& On-board control
Electrical
• Input voltage range: AC100–240V, 50-60Hz
• Power consumption: 300W
Physical
• LED display
• DMX connectors: 4 XLR connectors (XLR-3 In
and Out; XLR-5 In and Out)
• Power supply connectors: PowerCON® In/Out
• Cooling: Forced convection
• Dimensions: 455x333x318 mm. / 18x13x12.5 in.
• Weight: 7.5 Kg. / 16 Lbs.
ENGLISH VERSION

FRESNELED MKII
P.
3
2. SAFETY WARNING
• This product must be installed by a qualified pro-
fessional ONLY.
• All maintenance must be carried out by a qualified
electrician ONLY.
• All minimum distance of 0.5m must be maintained
between the equipment and a combustible surface.
• The product must always be operated in a well
ventilated area.
• DO NOT stare directly into the LED light source.
• Always disconnect the power before carrying out
any maintenance.
• The earth must always be connected to the ground
• Ensure that all parts of the equipment are kept
clean and free of dust.
• A minimum distance of 0.8m must be maintained
between the light and projecting surface.
ENGLISH VERSION

FRESNELED MKII
P.
4
ENGLISH VERSION
3. INSTALLATION
The LED fixture can be mounted in a hanging position using
the supporting bracket. The bracket should be secured to the
mounting truss or structure using a standard mounting clamp.
Please note that when hanging the unit a safety cable should
also be used.
Hanging
MOUNTING-
POWER CONNECTIONS
220-240V: 13 UNITS may be connected in series
110-120V: 6 UNITS may be connected in series

FRESNELED MKII
P.
5
ENGLISH VERSION
4. DISPLAY PANEL OPERATION
MENU: Return to the previous menu
ENTER: Enter the currently selected menu.
UP: Scroll down through the current menu list or decrease the
value of the current function.
DOWN: Scroll up through the current menu list or increase the
value of the current function.
DISPLAY OPERATION
QUICK-ACCESS KEYS
MENU: By press and holding the MENU key when at the
main menu it is possible to directly access the DIM function.
MENU MAP

FRESNELED MKII
P.
6
ENGLISH VERSION
DIMMER (DIM)
• DIM: This menu allows the user to manually control
the intensity of the fixture. Use <UP> or <DOWN>
keys to select required intensity.
NOTES:
• When using this function, if the MCON menu is set
as MAST, then the fixture will transfer the DIM val-
ues to other fixtures.
• When DMX data is received at the fixture, it will
automatically return to main menu after 2 minutes
of no key operation.
RUN MODE
• RUN: This menu allows the user to select the op-
erating mode of the fixture. Select DMX for nor-
mal DMX operation or SLAV for slave operation.
DMX ADDRESS
• ADDR: This menu allows the user to select the
startaddressofthefixture.Use<UP>or<DOWN>
keys to select required start address.

FRESNELED MKII
P.
7
ENGLISH VERSION
• SET: This menu allows the user to adjust key op-
eration settings for this fixture. KEY: Select <ON>
for automatic lock-out. Password to re-enter the
display is <UP>+<DOWN>+<UP>+<DOWN>.
• Select <DIM1>, <DIM2>, <DIM3> or <DIM4>
for different dimming speeds. <DIM4> is the slow-
est dimming speed).
• CURV: allows the user to adjust the shape of the
dimming curve. See the CURV chart to under-
stand more about actual dimming curves.
• PERF: this setting allows the user to select the
performance characteristics of the fixture.
• SLCK is used to lock the settings menu. When
SLCK is set to <ON> then user must insert pass-
code (UP+DOWN+UP+DOWN) in order to ac-
cess the settings menu.
• PERS this setting allows the user to select the
DMX personality of the fixture. Refer to DMX per-
sonality charts for specific details.
• DERR Chosose <SAVE> in order to save the last
DMX data incase of DMX signal error. Choose
<BLACK> in order to blackout in case of DMX signal error.
• In order to reset custom modes to default values
select <REST>.
• MCON: This function allows the user to select
whether the fixture will send DMX data to other
fixturesduringstand-aloneoperation.The<MAST>
setting allows data to be sent to Other fixtures.
The<SELF>settingisdefaultandwillnotsendDMX
data to other fixtures.
SPECIAL SETTINGS

FRESNELED MKII
P.
8
ENGLISH VERSION
CURV Dimming
WHITES CALIBRATION (CAL)
• Enter the <CAL> to select white color of different
color temperature.

FRESNELED MKII
P.
9
ENGLISH VERSION
5. USING A DMX512 CONTROLLER
CHANNEL ASSIGNMENT
NOTES:
• This product have two DMX512 channel configura-
tion: <UNO> / <DOS> / <STD.P>

FRESNELED MKII
P.
10
ENGLISH VERSION
6. APPENDIX