Tektronix P3410 User manual

The test & measurement
equipment you need at
the price you want.
Alltest carries the world’s largest selection of
used/refurbished benchtop test & measurement
equipment at 50% the price of new.
O
Our equipment is guaranteed working, warrantied, and
available with certified calibration from our in-house staff
of technicians and engineers.
• 10+ full time technicians with over 150 years of
specialization
• 90 day warranty & 5 day right of return on all
equipment
•
• 1-3 year warranties for new and
premium-refurbished equipment
• Every unit tested to OEM specifications
• Satisfaction guaranteed
You have plans, we will help you achieve them.
Any project. Any budget.
Get a quote today!
CCall [phone] or email [e-mail].
t
Alltest Instruments, Inc.
500 Central Ave.
Farmingdale, NJ 07727
P: [phone]
F: [phone]
alltest.net
s
[e-mail]

P3410 and P3420 Instructions
Instructions
This package contains either a P3410 TTL pod or a P3420 variable
pod. Twelve cables are supplied with each pod (012-1502-XX for
the P3410 and 012-1504-XX for the P3420). Both pods are designed
to be used with the Tektronix DG2020 or DG2020A Data Generator.
Refer to Figure 1 to determine which pod you are using.
Information for installation, operations, specifications, and
accessories can be found in the DG2020 or DG2020A User Manual.
The following instruction describes about the cable connection only
between the Pod and the DG2020A. However, if your data generator
is the DG2020, you can also read this instruction as replacing
DG2020A with DG2020.
Precaution for Connecting Cable
CAUTION. Make sure that you have correctly inserted the cable
plug in the DG2020A and the pod before turning on power. The
yellow wire end of the connector must be aligned with the
triangular yellow index mark on the DG2020A or pod.
Incorrectly connected cables will damage the DG2020A and the
pod.
Note that the connectors on the DG2020A rear panel are installed
with the tab slot down, and the connector on the pod rear panel is
installed with the tab slot up (see Figure 2).
To connect a cable between the DG2020A and a pod, align the yellow
wire end of the cable connector with the triangular yellow index
mark on the DG2020A or pod connector. Doing this also correctly
aligns the connector alignment tab. See Figure 2. Then carefully but
firmly insert the cable connector into the DG2020A or pod connector.
For further information for connection, refer to the DG2020A User
Manual titled DG2020A Data Generator With P3410 & P3420 Pods.
P3420 Front Panel
P3410 Front Panel
Figure 1: P3410 and P3420 front panels
Yellow Index
Mark
Pod Rear Panel
DG2020A Rear Panel
Tab Slot
Tab Slots
Yellow Index
Mark
To connect a cable between the DG2020A and a
pod, align the yellow wire end of the cable connector
with the triang lar yellow index mark on the
DG2020A or pod connector. Doing this also correctly
aligns the connector alignment tab. Then caref lly
b t firmly insert the cable connector into the
DG2020A or pod connector.
Yellow Wire
Cable
Tab
Figure 2: ellow index mark and yellow wire for cable connection

Tektronix 070-A656-50
ອᛱᓢᡆώ୎ᔧ
᝜ёубȼиϋϏ P3410 ിTTL ѝущϞοϏ P3420 ിѐѪТіѫȦ
ѝущώΤκϬΫώѝущάᓾσφΤϞιȣϞοȢ ၠТЯлеѪψη
φ୆ѝущᡑϋ 12 ᝜лушώбȼіѫάᒱອεϬφΤϞιȣѝущ (ᅞ
1༲჈)ΪϨϓТЯлеѪϲδ୎ᔧίπεΤȣϊΪȢбȼіѫȦлуш
ώᙴᙊᗖ๦ϏྡώψΪϪχιȣ
HP3410 ിᡑбȼіѫȦлуш : 012-1502-XX
HP3420 ിᡑбȼіѫȦлуш : 012-1504-XX
୆ѝущώበ໮᛽ᜡȢཅᡍȢΪϨϓТЯлеѪϋτΤφϏ DG2020ി
ϞοϏ DG2020A ി᥂ᚸѦȼжȦўыѥТѫϲ༲჈ηφίπεΤȣ
ϊΪγώФѳйшѩЯзѧѳϏȢDG2020AിψៀభηφΤϞιάȢ
DG2020ിϋዐηφϢᒱᡍϋᐬεϬϞιȣ
бȼіѫᇜኳώໝώ፭৕
፭৕ȧбȼіѫȦїѩаϲქ઼ౕϋηφ DG2020A ിϞοϏѝущώ
гэЯпϋᇜኳηϊΤχίπεΤȣбȼіѫȦїѩаϲქ઼ϲౕϋᇜኳ
ηοϞϞ DG2020A ിώᑅරϲᓾϬϫψȢDG2020A ിΫϩѝущϋ
ૡዧϊᑅ᢮ά᢮ϬȢмэѬȼпΪϨϓѝущϋኻၽϲᠿΨϞιȣ
DG2020Aി෥ᙴёэѫώѝущᇜኳᡑгэЯпψѝущ෥ᙴёэѫώ
гэЯпϏȢпіȦйѭушৌፖάქ઼ౕ෾έϋ࿨ϪᙕαϩϬφΤϫγ
ψϋ፭৕ηφίπεΤ (ᅞ2 ༲჈)ȣ
DG2020AിψѝущϲᇜኳιϫໝϋϏȢгэЯпȦїѩаώпіψг
эЯпώпіȦйѭушȢΪϨϓбȼіѫώફᄧώѩФѳ (Yellow
wire) ψгэЯпώફᄧώўȼЯ (Yellow index mark) ϲ๧ϯλφίπ
εΤȣᅞ 2 ϲ༲჈ηφίπεΤȣ
νώኾώᇜኳώნ໙ϋτΤφϏ DG2020A ി᥂ᚸѦȼжȦўыѥТѫ
ϲ༲჈ηφίπεΤȣ
F
irst Printing: October 2002
Copyright
©
Tektronix Japan, Ltd. All rights reserved.
C
opyright ©Tektronix, Inc. All rights reserved.
T
ektronix products are covered by U.S. and foreign patents, issued and pending.
I
nformation in this publication supercedes that in all previously published material.
S
pecifications and price change privileges reserved.
T
ektronix Japan, Ltd., 5–9–31 Kitashinagawa, Shinagawa–ku, Tokyo 141–0001 Japan
T
ektronix, Inc., P.O. Box 500, Beaverton,, OR 97070
T
EKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Instructions
P3410 TTL Pod
P3420 Variable Pod