Tektronix 2225 User manual

Tektronix 2225 Oscilloscope
1. Summary of Controls, Connectors, and Indicators
No. Title Function Recommended Use
1 INTENSITY Adjusts trace brightness. Compensate for ambient lighting,
trace s
p
eed
,
tri
gg
er fre
q
uenc
y
.
2BEAM FIND Compresses display to within CRT
limits.
Locate off-screen phenomena.
3FOCUS Adjusts for finest trace thickness. Optimize display definition.
4TRACE
ROTATION
Adjusts trace parallel to centerline. Compensate for earth's field.
5POWER Turns power on and off. Control power to the instrument.
6Power Indicator Illuminates when power is turned on. Know power condition.
7,9 POSITION Moves trace up or down screen. Position trace vertically and
compensate for dc component of
si
g
nal.
8TRACE SEP Moves the magnified trace vertically
with respect to the unmagnified trace
when HORIZONTAL MODE is set to
ALT.
Position unmagnified and
horizontally magnified traces for
convenient viewing and
measurement.
10 CH 1-BOTH -
CH2
Selects signal inputs for display. View either channel independently
or both channels simultaneousl
y
11 NORM- INVERT Inverts the Channel 2 signal display. Provide for differential (CH 1 - CH 2)
or summed (CH 1 + CH 2) signals
when ADD is selected.

No. Title Function Recommended Use
12 ADD-ALT- CHOP ADD shows algebraic sum of CH 1 and
CH 2 signals. ALT displays each
channel alternately. CHOP switches
between CH 1 and CH 2 signals during
the sweep at 500 kHz rate.
Display summed or individual
signals.
13 VOLTS/DIV Selects vertical sensitivity. Adjust vertical signal to suitable
size.
14 Variable (CAL) Provides
continuously
variable deflection
factors between
calibrated
positions of the
VOLTS/DIV
switch. Reduces
gain by at least
25:1.
The CAL control
can be pulled out
to vertically
magnify the trace
by a factor of 1 0.
Limits bandwidth to
5 MHz.
Match signals for
common mode
readings. Adjust
height of pulse
for rise-time
calculations.
Inspecting small
signals.
15 AC-GND-DC In AC, isolates dc component of signal.
In GND, gives reference point and
allows precharging of input coupling
capacitor. In DC, couples all
components of signal.
Selects method of coupling input
signals to the vertical deflection
system.
16 CH 1 OR X CH 2
ORY
Provides for input signal connections.
CH 1 gives horizontal deflection when
SEC/DIV is in X-Y.
Apply signals to the vertical
deflection system.
17 POSITION
COARSE
COARSE is convenient for moving
unmagnified traces
Control trace
horizontal
positioning in
direction.
18 POSITION FINE FINE is convenient for moving
magnified traces when either ALT or
MAG is selected.
Control trace
horizontal
positioning in
direction.
19 X1 -ALT- MAG X1 displays only normal (horizontally
unmagnified) waveform. ALT displays
normal and magnified waveforms
alternately. MAG displays only the
magnified waveform.
Select normal, comparative or
expanded waveforms.
20 SEC/DIV Selects time-base speed. Set horizontal speed most suited to
re
q
uirements.
21 Variable (CAL) Provides continuously variable
uncalibrated sweep speeds to at least
2.5 times the calibrated setting.
Extend the slowest speed to at least 1
.25 s/div
22 MAG(X5-X10-
X50)
Selects degree of horizontal
magnification.
Examine small phenomena in
detail.
23 Provides safety
connection to
earth and direct
si
g
nal source.
Chassis ground connection.
24 PROBE ADJUST Provides approximately 0.5-V,1-kHz
square wave.
Match probe capacitance to individual
circuit. This source may be used to
check the basic functioning of vertical
and horizontal circuits but is not
intended to check their accuracy.

No. Title Function Recommended Use
25 SLOPE Selects the slope of the signal that
triggers the sweep.
Provide ability to trigger from
positive-going or negative-going
signals.
26 LEVEL Selects trigger-signal amplitude point. Select actual point of trigger.
27 TRIG'D Indicator lights when sweep is triggered
in P-P AUTO, NORM, or TV FIELD.
Indicate trigger state.
29 RESET Arms trigger circuit for SQL SWP.
30 HOLDOFF Varies sweep holdoff time 1 0:1 . Improve ability to trigger from
a
p
eriodic si
g
nals.
31 SOURCE CH 1,CH2, and EXT trigger signals
are selected directly. In VERT MODE,
trigger source is determined by the
VERTICAL MODE switches as follows:
CH 1 : trigger comes from Channel 1
signal. CH 2: trigger comes from
Channel 2 signal. BOTH -ADD and
BOTH CHOP: trigger is algebraic sum
of Channel 1 and Channel 2 signals.
BOTH-ALT: trigger comes from
Channel 1 and Channel 2 on alternate
swee
p
s.
Select source of signal that is
coupled to the trigger circuit.
32 COUPLING AC blocks dc components and
attenuates signals below 15 Hz. LF
REJ blocks dc components and
attenuates signals below about 30
kHz. HF REJ blocks dc components
and attenuates signals above about 30
kHz. DC couples all signal
components.
Select how the triggering signal is
coupled to the trigger circuit.
33 EXT INPUT Connection for Connection for
applying external applying external
signal that can be signal that can be
used as a trigger, used for intensity
modulation.
Trigger from a Provide
source other reference blips
than vertical by intensity
signal. Also modulation from
used for single- independent
shot application. source.
2. Learning the Controls
After turning the power on, let the oscilloscope warm up for a few minutes before starting this
procedure.
• Set instrument controls as follows:
Display
INTENSITY
FOCUS
Midrange
Midrange

Vertical (both channels)
POSITION Midrange
MODE CH 1
VOLTS/DIV 0.5 V (1 OX PROBE)
VOLTS/DIV Variable CAL detent (fully clockwise)
Input Coupling AC
Horizontal
COARSE POSITION Midrange
MODE X1
SEC/DIV 0.2 ms
SEC/DIV Variable CAL detent (fully clockwise)
Trigger
SLOPE /
LEVEL Midrange
MODE P-PAUTO
HOLDOFF MIN
SOURCE CH 1
COUPLING AC
Connect a probe to the input BNC connector for Channel 1 (labeled CH 1 OR X).
Attach the probe ground lead to the collar of the EXT INPUT connector and apply the
probe tip to the PROBE ADJUST terminal. If necessary, adjust the TRIGGER LEVEL
control to get a stable display.
Change the Channel 1 input coupling switch to GND and use the Channel 1
POSITION control to align the baseline trace to the center horizontal graticule line.
This sets the zero reference for the display.
Switch input coupling back to AC. Notice that the square wave is centered vertically
on the screen. Now switch input coupling to DC and observe what happens to the
waveform. The zero reference is maintained at the center horizontal graticule line.
NOTE: More information about using the controls is contained at the end of this procedure. Refer to it as
often as needed while learning the front-panel controls.
Use the following controls and notice the effect each has on the displayed waveform
as the settings are changed.
Each POSITION control
CH 1 VOLTS/DIV
CH 1 VOLTS/DIV Variable (CAL)
SEC/DIV
SEC/DIV Variable (CAL)
HORIZONTAL MODE
HORIZONTAL MAG
TRACE SEP
TRIGGER SLOPE
At this point, connect the second probe to the CH 2 OR Y input connector. Set the
VERTICAL MODE switch to CH 2 and TRIGGER SOURCE to CH 2, then follow
steps 2 through 5 again, using the channel 2 controls.

Now set the VERTICAL MODE switches to BOTH-NORM-ALT and return both
VOLTS/DIV switches to 0.5 V (10X PROBE). Rotate all variable controls clockwise to
their CAL detents. Set the TRIGGER SOURCE switch to VERT MODE. Then use the
VERTICAL POSITION and TRACE SEP controls to position the four traces to
convenient locations on the screen.
While watching the Channel 2 waveforms, set the middle VERTICAL MODE switch to
CH 2 INVERT and notice the effect. Then set the right MODE switch to ADD. What
happens to the waveforms? Finally, return the middle MODE switch to NORM. What
waveform is displayed now?
Congratulations! You now know how to use the 2225 front-panel controls to display signals and move
them about on the screen. The remainder of this section gives you more information about the controls
and offers suggestions for their use.
3. Display Controls
Set the INTENSITY control for comfortable viewing, but no brighter than you need. Use
high-intensity settings to observe low-repetition-rate signals, narrow pulses in long time
intervals, or occasional variations in fast signals.
4. Vertical Controls
When making voltage measurements, rotate the VOLTS/DIV CAL control fully clockwise
(in detent). Best accuracy can be achieved by setting the VOLTS/DIV control for the
largest display possible.
A. Input Coupling
For most applications use DC input coupling. This mode is compatible with the
standard-accessory, high-impedance probes and it displays logic levels and dc levels
of static signals.
Use GND input coupling to show where the 0-volt level will be located when you shift
to DC or AC coupling.
Use AC coupling for the special cases where you need to see small signals on large
dc voltage levels.
B. Channel Selection
With the three VERTICAL MODE buttons, you can display combinations of the two
vertical channels. When CH 1 is selected, the other two MODE switches are not
active. When CH 2 is selected, the middle MODE switch (NORM/CH 2 INVERT)
becomes active. And when BOTH channels are selected for display, all three MODE
switches are active.

C. ADD and INVERT
Select ADD mode to display the algebraic sum of the CH 1 and CH 2 signals. When
you use ADD, the CH 1 and CH 2 VOLTS/DIV settings should be equal.
Selecting CH 2 INVERT changes the sense of the CH 2 waveform. This allows you to
see the difference between the CH 1 and CH 2 signals on the ADD trace.
D. CHOP or ALT?
When BOTH channels are selected, the display is time-shared. The CHOP mode
displays each channel for a short time and multiplexes during the sweep to give the
appearance of displaying both channels at once. This mode (CHOP) works better
than ALT for sweep speeds slower than 1 ms per division and for low-repetition-rate
signals that make the display flicker (up to 2 s/division).
The ALT mode displays each channel for the duration of a complete sweep. It gives a
cleaner display of multiple channels than CHOP does and is usually preferred at
moderate to high sweep speeds.
E. Increasing the Sensitivity
Pulling the VOLTS/DIV CAL control out (towards you) magnifies the vertical axis by a
factor of 10, increasing the sensitivity to 500 (iV per division. This function is useful for
investigating small-amplitude signals (in general, less than 5 mV p-p) or small
amplitude details on larger signals.
5. Horizontal Controls
A. Sweep-Speed Selection
The unmagnified sweep (MODE set to X1) is the horizontal function needed for most
applications. Best measurement accuracy is achieved by setting the SEC/DIV control
for the fastest sweep that will display the interval of interest. The variable control (CAL)
should be in its detent (fully clockwise).
B. Magnifying Waveform Details
Each of the two magnified modes—ALT or MAG—expands the unmagnified trace.
When ALT is chosen, both the unmagnified and the magnified waveforms appear
together on the crt screen. Vertical separation between them is adjusted with the
TRACE SEP control. If MAG is selected, only the magnified trace is displayed on
screen. This is useful for eliminating unwanted clutter from the crt when you are
making accurate timing measurements or looking at waveform details. Whenever ALT
or MAG is set on the upper HORIZONTAL MODE switch, the amount of waveform
expansion is determined by the setting of the HORIZONTAL MAG switch located
beneath the SEC/DIV control. Three magnifications are available—5X, 10X, and SOX.
Having the ability to select various combinations of waveform expansion and SEC/DIV
control setting lets you extend the time-base range out to a maximum of 5 ns per
division.
The marker that links the timing of the unmagnified and magnified traces with each
other is the center vertical graticule line. The intersections of that line with the
unmagnified and the magnified waveforms are the points of equal time duration from
sweep start. With the center vertical graticule as the reference line, the investigation of
waveform details around any point on the unmagnified trace, as well as the
measurement of time with greater accuracy, then become easy tasks.

6. Trigger Controls
For most signals, the trigger-control settings that will yield hands off triggering are:
MODE P-P AUTO
HOLDOFF MIN
SOURCE VERT MODE
COUPLING DC
A. Which Mode to Use
P-P AUTO/TV LINE—With this mode set, the range of the LEVEL control is confined
to the values between the triggering-signal peaks. For example, selecting P-P AUTO
and rotating the LEVEL control to the center half of its range establishes a trigger point
that is about midway between the peaks of the triggering signal.
In this mode, the absence of a triggering signal causes the sweep to free-run. And
with signals below 20 Hz, the P-P AUTO circuit may not find the correct level.
Whenever P-P AUTO is active and VERT MODE source selected, the triggering
signal is supplied by the channel that is being displayed—or by Channel 1 in a two-
channel display.
The P-P AUTO mode is effective for monitoring logic signals and television lines
having at least a 20-Hz repetition rate. Selecting P-P AUTO at the instrument front
panel also sets the TV LINE triggering mode.
NORM—This mode produces a sweep only when the triggering signal meets the
criteria set by the LEVEL and SLOPE controls. With NORM mode selected, range of
the LEVEL control is sufficient to set any voltage threshold that can be displayed by
the instrument. In the absence of a triggering signal, there is no sweep.
Use the NORM mode for viewing infrequent events and erratic signals.
SQL SWP—When this mode is selected, the sweep is triggered only once. Press the
RESET button once to arm the trigger circuit and illuminate the READY indicator.
When a trigger event occurs, the sweep runs once and the READY light extinguishes.
Use the SQL SWP mode to display or photograph non-repetitive or unstable signals.
TV FIELD—This mode triggers the sweep at the beginning of a television field. To
change the TV field being displayed, you must interrupt the trigger signal by setting
the input coupling switch momentarily to GND then back to either DC or AC until the
desired field is displayed.
To display Field 1 and Field 2 at the same time, connect the same television signal to
both the CH 1 and CH 2 inputs; set VERTICAL MODE to BOTH and ALT; set the
SEC/DIV control to 0.5 ms or faster sweep speed.
If you magnify the vertical display beyond the graticule, the trigger may be degraded.
To avoid trigger overload, use either CH 1 or CH 2 for display and use the EXT
INPUT channel with an appropriate video signal as the trigger source. A composite
sync signal can be used for the trigger source as well as composite video.

B. Source
Choose a single trigger source to correctly display the timing relationships between
two channels. Choose the channel with the lowest-frequency signal to avoid
ambiguous displays.
With VERT MODE TRIGGER SOURCE and either P-P AUTO TRIGGER MODE or
CHOP VERTICAL MODE, the triggering signal is the algebraic sum of the Channel 1
and Channel 2 input signals.
Use a composite trigger source only to compare asynchronous signals. To generate a
composite trigger: select VERT MODE TRIGGER SOURCE, BOTH-ALT VERTICAL
MODE, and any TRIGGER MODE except P-P AUTO.
C. Coupling
For signals with strongly interfering components, HF Reject and LF Reject coupling
give added selectivity. When AC coupling is selected, triggering continues as the dc
level of the signal changes.
D. Slope
Use the SLOPE control to select either the rising (/) or the falling (\) edge of the signal
to trigger the sweep.
E. Leve l
The LEVEL control gives you complete freedom to choose the most appropriate
threshold voltage on a signal to initiate sweeps whenever any trigger mode except P-
P AUTO is selected.
F. Holdoff
With irregular signals such as bursts, the HOLDOFF setting can improve display
stability. Also, if the signal has a fixed pattern of variation from cycle to cycle, some
modes of the signal may be omitted from the display. Changing the HOLDOFF setting
can force the instrument to display all the modes of the signal. Normally, the
HOLDOFF control should be set at MIN.
7. Calibration Summary
Calibrate the voltage (vertical) and time (horizontal) scales of the scope as follows:
1) Connect a wire from the PROBE ADJUST to CH1 or CH2.
2) Adjust the trace using the position controls until the square wave is located at
aconvenient position on the screen.
3) Measure the height of the square wave in volts. You should find that it is 0.5
Voltspeak-to-peak so that the 0.1 V/div scale is appropriate. Make certain that the
Variable
(CAL) knob is in its calibrated (detent) position. If the square wave does not measure
0.5 V ask your TA for help.
4) Measure the period of the square wave in seconds. Use a time scale setting that
displays several cycles of the square wave. In order to obtain the best accuracy,
measure the time for several cycles and divide by the number of cycles. Again make
certain that the Variable (Cal) knob for the horizontal sweep (SEC/DIV) is in the
calibrated (detent) position. The period should be 10~3seconds.