Tekvox TEK 1201-MV User manual

www.tekvox.com
1201-MV
79033-MV User Manual
TEK 1201-MV
6x1 4K Seamless Multiview Presentation Switcher with
HDBaseT
All Rights Reserved
Version: 79033-MV_2020V1.2

www.tekvox.com
1201-MV
79033-MV User Manual
Preface
Read this user manual carefully before using the product. Pictures shown in this manual are for
reference only. Different product model specifications may vary.
This manual is only for operation instruction, please contact the local distributor for maintenance
assistance. The functions described in this version were updated November, 2020. In order to
continue improving the product, we reserve the right to make function or parameter changes without
notice or obligation. Please refer to the dealers for the latest details.
Trademarks
Product model and logo are trademarks. Any other trademarks mentioned in this manual are
acknowledged as the properties of the trademark owner. No part of this publication may be copied
or reproduced without the prior written consent.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. It has
been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a commercial installation.
Operation of this equipment in a residential area is likely to cause interference, in which case the
user at their own expense will be required to take whatever measures may be necessary to correct
the interference.
Any changes or modifications not expressly approved by the manufacture would void the user’s
authority to operate the equipment.

www.tekvox.com
1201-MV
79033-MV User Manual
Safety Precautions
To ensure the best performance from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
•Unpack the equipment carefully, and save the original box and packing material for possible
future shipment
•Follow basic safety precautions to reduce the risk of fire, electrical shock, and injury to persons
•Do not dismantle the housing or modify the module (electrical shock or burn hazard)
•Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration, or malfunction
•Refer all servicing to qualified service personnel
•To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product
near water
•Do not put any heavy items on the product’s power cable
•Do not remove the housing of the device as opening or removing housing may expose you to
dangerous voltage or other hazards
•Install the device in a place with sufficient ventilation to avoid damage caused by overheating
•Keep the module away from liquids
•Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object
or liquid falls or spills on to the housing, unplug the module immediately.
•Do not twist or pull by force ends of the optical cable. It can cause malfunction.
•Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning.
•Unplug the power cord when left unused for a long period of time
•Information on disposal for scrapped devices: do not burn or mix with general household
waste, please treat them as normal electrical wastes

www.tekvox.com
1201-MV
79033-MV User Manual
Table of Contents
1. Product Introduction ....................................................................................................................6
1.1 Features...............................................................................................................................................6
1.2 Package List........................................................................................................................................7
1.2.1 TEK 1201-MV Switcher..............................................................................................................7
1.2.2 TEK 1201-MV-RX Receiver ........................................................................................................7
2. Specifications ..............................................................................................................................7
2.1 Switcher ...............................................................................................................................................7
2.2 Receiver ...............................................................................................................................................9
3. Panel Description.......................................................................................................................10
3.1 Switcher Front Panel.........................................................................................................................10
3.2 Switcher Rear Panel..........................................................................................................................11
3.3 Receiver Front Panel.........................................................................................................................12
3.4 Receiver Rear Panel ..........................................................................................................................12
3.5 System Connection...........................................................................................................................13
4. Front Panel Control ....................................................................................................................13
4.1 Multiview Mode Selection ................................................................................................................13
4.2 Full Screen Setting ............................................................................................................................14
4.3 HDMI Output Settings.......................................................................................................................14
4.4 Audio Control.....................................................................................................................................14
4.5 Video Signal Switching.....................................................................................................................15
4.6 Switching Status ...............................................................................................................................15
5. GUI Control ................................................................................................................................16
5.1 Control Tab........................................................................................................................................17
5.1.1 Video Control............................................................................................................................17
5.1.2 Display Control .........................................................................................................................18
5.1.3 Audio Control............................................................................................................................19
5.2 Multiview Tab ....................................................................................................................................20
5.2.1 Pre-Defined Multiview Mode...................................................................................................20

www.tekvox.com
1201-MV
79033-MV User Manual
5.2.2 User-Defined Multiview Mode .................................................................................................22
5.3 Display Setting Tab...........................................................................................................................23
5.4 Resolution Tab ..................................................................................................................................24
5.5 CEC Tab .............................................................................................................................................25
5.5.1 Source Control..........................................................................................................................25
5.5.2 Display Control .........................................................................................................................25
5.5.3 User-Defined CEC Command ..................................................................................................26
5.6 EDID Tab ............................................................................................................................................27
5.6.1 EDID Setting..............................................................................................................................27
5.6.2 EDID Upload..............................................................................................................................27
5.7 Network Tab ......................................................................................................................................28
5.8 Tags Tab............................................................................................................................................28
5.9 Security Tab.......................................................................................................................................29
5.10 Additional Tab.................................................................................................................................29
5.11 GUI Upgrade ....................................................................................................................................30
6. IR Remote Control ......................................................................................................................31
7. RS232 Control............................................................................................................................32
7.1 System Commands ..........................................................................................................................33
7.2 Signal Switching Commands...........................................................................................................34
7.3 Audio Setting Commands ................................................................................................................36
7.4 Function Setting Commands ...........................................................................................................37
7.5 CEC Commands................................................................................................................................44
7.6 Special Commands...........................................................................................................................46
8. Firmware Upgrade......................................................................................................................50
8.1 Switcher .............................................................................................................................................50
8.2 Receiver .............................................................................................................................................50

www.tekvox.com
1201-MV
79033-MV User Manual
1. Product Introduction
The 6x1 4K seamless presentation switcher kit consists of a TEK 1201-MV switcher and a TEK 1201-
MV-RX receiver. The switcher offers five HDMI and one USB-C input, along with mirrored HDBaseT
and HDMI outputs. The HDBaseT output supports PoH and can be paired with a compatible
HDBaseT receiver to extend 4K@60Hz 4:4:4 / 1080P signals up to 328 feet (100 meters) over a
single CAT cable.
The switcher supports audio mixing, and audio embedding & de-embedding. It also supports
multiview functionality and provides up to 16 multi-mode layouts. The switcher features a wide
range of control flexibility via front panel buttons, built-in web GUI, IR remote, RS232, and CEC.
1.1 Features
⚫6x1 4K seamless presentation switcher with multiview functionality
⚫Supports HDMI V2.0 resolutions up to 4K@60Hz 4:4:4, HDCP 2.2
⚫12 flexible Multiview configurations for showing up to 4 sources at once
⚫Auto-switching while in single-window mode
⚫Supports auto-scaling (Default output resolution: 4K@60Hz 4:4:4)
⚫Cycles through the windows from A to D via the Swap button in the GUI
⚫Resizes the windows in 3 diffe rent sizes
⚫Bi-directional USB management
⚫Supports audio mixing, audio embedding, and audio de-embedding
⚫Extends 4K or 1080p signals up to 328 feet (100 meters) over a single CAT Ethernet cable
⚫Supports Ethernet signal extension
⚫Supports PoC with 12~48V wide voltage range
⚫Supports RS232, IR, CEC, and GUI control
⚫The HDMI output can be set to preview the HDMI 1 input or mirror the HDBaseT output
⚫Mic with phantom power selection
⚫Line input for mic mixing
⚫Controllable via RS232, IR remote, front panel buttons, or TCP/IP commands
⚫Supports bidirectional USB 3.0 at switcher and receiver. Over the HDBaseT the USB is limited
to USB 2.0

www.tekvox.com
1201-MV
79033-MV User Manual
1.2 Package List
1.2.1 TEK 1201-MV Switcher
⚫1x 6x1 4K Presentation Switcher
⚫2x Mounting Ears with 4 Screws
⚫4x Plastic Cushions
⚫2x 3-pin Terminal Blocks
⚫1x 4-pin Terminal Block
⚫1x 5-pin Terminal Block
⚫1x IR Remote
⚫1x IR Receiver
⚫1x Power Adapter (24V DC 5A)
⚫1x Power Cord
⚫1x User Manual
1.2.2 TEK 1201-MV-RX Receiver
⚫1x HDBaseT Receiver
⚫2x Mounting Ears with 2 Screws
⚫4x Plastic Cushions
⚫1x RS232 Cable (3-pin to DB9)
Note: Please contact your distributor immediately if any damage or defect in the components is found.
2. Specifications
2.1 Switcher
Video Input
Video Input
(5) HDMI IN (Type-A, Female)
(1) USB-C (USB Type-C, Female)
Input Resolution
HDMI (1~4): Up to 4K@60Hz 4:4:4
HDMI (5): Up to 4K@30Hz 4:4:4
USB-C: Up to 4K@30Hz 4:4:4
Video Output
Video Output
(1) HDMI (Type-A, Female)
(1) HDBaseT (RJ45)
Output Resolution
HDMI: Up to 4K@60Hz 4:4:4
HDBaseT: Up to 4K@60Hz 4:2:0
HDMI Standard
Up to 2.0

www.tekvox.com
1201-MV
79033-MV User Manual
HDCP Version
Up to 2.2
Audio Input
Audio Input
(1) AUDIO IN, (1) LINE, (1) MIC
Audio Input Connector
(1) 3.5mm jack, (2) 3-pin terminal blocks
Frequency Response
20Hz to 20kHz, ±3dB
Max Input Level
2.0Vrms ± 0.1
L-R Level Deviation
< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)
Input Impedance
> 10KΩ
AUDIO/LINE/MIC Audio Format
PCM 2.0
HDMI Audio Format
PCM 2.0 48K
L+R Audio Output
Audio Output
(1) L+R (5-pin terminal block)
Audio Format
PCM 2.0
Frequency Response
20Hz to 20kHz, ±1dB
Max Output Level
2.0 ± 0.1Vrms
THD+N
< 0.05%, 20Hz to 20kHz bandwidth, 1kHz sine at 0dBFS level (or
max level)
Signal-to-Noise Ratio
> 90dB, 20Hz to 20kHz bandwidth
Crosstalk Isolation
< -70dB, 10kHz sine at 0dBFS level
L-R Level Deviation
< 0.3dB, 1kHz sine at 0dBFS level (or max level before clipping)
Output Load Capability
1kΩ and higher (Supports 10x paralleled 10kΩ loads)
Noise Level
- 80dB
SPDIF Audio Output
SPDIF Out
(1) SPDIF (Toslink)
Audio Format
PCM 2.0
Max Output level
±0.3dBFS
Frequency Response
20Hz to 20kHz, ±1dB
THD+N
< 0.05%, 20Hz to 20kHz bandwidth, 1kHz sine at 0dBFS level (or
max level)
Signal-to-Noise Ratio
> 90dB, 20Hz to 20kHz bandwidth
Crosstalk isolation
< -70dB, 10kHz sine at 0dBFS level (or max level before
clipping)
Noise Level
- 90dB
Control
Control port
(1) PC, (2) DEVICES, (1) IR IN, (1) IR OUT, (1) IR EYE,
(1) FIRMWARE, (1) RS232, (1) TCP/IP
Control Connector
(1) Type-B USB, (2) Type-A USB 3.0, (3) 3.5mm jack, (1) Type-A
USB, (1) 4-pin terminal block, (1) RJ45
General
Transmission Distance
4K@60Hz 4:4:4/1080p ≤ 328 feet (100 meters)
Bandwidth
18Gbps
Operation Temperature
23° ~ 131°F (-5°C - 55°C)
Storage Temperature
-13° ~ 158°F (-25°C ~ 70°C)

www.tekvox.com
1201-MV
79033-MV User Manual
Relative Humidity
10% to 90%, Non-condensing
External Power Supply
Input: 100 ~ 240VAC, 50/60Hz
Output: DC 24V, 5A
Power Consumption
90w (Max)
USB-C Power Charging
60w (Max)
Product Dimensions
9.84”(250mm) x 1.73” (44mm) x 7.87” (200mm)
Product Weight
3.53lbs (1.6kg)
2.2 Receiver
Video
Video Input
(1) HDBT IN (RJ45)
Video Output
(1) HDMI OUT (Type-A, Female)
HDBT Input Resolution
Up to 4K@60Hz 4:2:0
HDMI Output Resolution
Up to 4K@60Hz 4:4:4
HDMI Standard
Up to 2.0
HDCP Version
Up to 2.2
Audio
Audio Output
(1) SPDIF OUT (Toslink)
Audio Format
PCM 2.0
Max Output level
±0.3dBFS
Frequency Response
20Hz to 20kHz, ±1dB
THD+N
< 0.05%, 20Hz to 20kHz bandwidth, 1kHz sine at 0dBFS level (or
max level)
Signal-to-Noise Ratio
> 90dB, 20Hz to 20kHz bandwidth
Crosstalk isolation
< -70dB, 10kHz sine at 0dBFS level (or max level before clipping)
Noise Level
- 90dB
Control
Control
(1) PC, (3) DEVICES, (1) FW, (1) ETHERNET, (1) IR IN,
(1) IR OUT, (1) RS232
Control Connector
(1) Type-B USB, (3) Type-A USB 3.0, (1) Micro-USB, (1) RJ45, (2)
3.5mm jack, (1) 3-pin terminal block
General
Transmission Distance
4K@60Hz 4:4:4/1080p ≤ 328 feet (100 meters)
Bandwidth
18Gbps
Operation Temperature
23° ~131°F (-5 ~55°C)
Storage Temperature
-13° ~158°F (-25 ~ 70°C)
Relative Humidity
10% to 90%, Non-condensing
External Power Supply
Power over Cable (PoC)
Power Consumption
10w (Max)
Product Dimensions
6.61” (168mm) x 0.91” (23mm) x 5.31” (135mm)
Product Weight
1.1lbs (500g)

www.tekvox.com
1201-MV
79033-MV User Manual
3. Panel Description
3.1 Switcher Front Panel
1. IR LED: Built-in IR sensor; receives IR signals sent from IR remote
2. POWER LED: Lights up red when switcher is in standby mode, or green when device is powered on
3. INPUT BUTTONS:
⚫1~6: Input source selectors
⚫AUTO: Enables or disables auto-switching when in Fullscreen mode
4. MULTIVIEW: Selects the four most commonly used built-in multiview modes
5. SELECT/FULL SCREENS (A~D): Window A ~ D buttons for output selection and Fullscreen setting
6. MIRROR: Sets the local HDMI output as HDBT loop out. (e.g. HDMI and HDBT ports
simultaneously output the same signal source)
7. BYPASS HDMI 1: Sets the local HDMI output port to output the HDMI input 1 source signal
8. AUDIO CONTROL:
⚫Press the volume knob to select MIC or SOURCE audio to be controlled. With MIC audio
selected, the MIX and MIC mixing audio inputs are controlled simultaneously.
⚫Rotate the knob to increase or decrease the volume of the selected audio
⚫Press and hold the knob for at least 3 seconds to mute the selected audio; rotate the knob to
unmute.
Note: Please refer to 4. Front Panel Control for more details about button usages.
3
125678
4

www.tekvox.com
1201-MV
79033-MV User Manual
3.2 Switcher Rear Panel
1. INPUTS:
⚫Five HDMI inputs and one USB-C input.
⚫One external audio input for HDMI input 1.
2. OUTPUTS: One HDMI and one HDBaseT output. The HDBaseT output supports PoH.
3. AUDIO IN:
⚫MIX: Mix audio input for audio mixing.
⚫MIC: Microphone input for audio mixing. Set 48V phantom power mode switch as needed (ON
for Condenser microphone; OFF for Dynamic microphone)
4. AUDIO OUT:
⚫L+R: Balanced analog audio output for audio de-embedding.
⚫SPDIF: SPDIF audio output for audio de-embedding.
5. CONTROL:
⚫PC: Type-B USB port for Host PC connection. The Host PC can be controlled by the USB
devices (e.g. mouse, keyboard, etc.) which are connected to the USB Type-A ports (DEVICES).
⚫DEVICES (1~2): Two type-A USB ports for USB devices connection (e.g. mouse, keyboard,
etc.). These USB devices are used to control the Host PC.
⚫IR IN: Connects to IR receiver for IR pass-through.
⚫IR OUT: Connects to IR emitter for IR pass-through.
⚫IR EYE: Connects to IR receiver for switcher control.
⚫FIRMWARE: Type-A USB for firmware upgrade.
⚫RS232: Connects to a control device (e.g. PC) or a third-party device for RS232 control
⚫TCP/IP: Connects to a control device (e.g. PC) to control the switcher by GUI.
6. DC 24V: DC connector for power adapter connection.
INPUTS
1. HDMI 2. HDMI 3. HDMI 4. HDMI 5. HDMI
AUDIO IN
L R
MIX ON
Phantom 48V)
(
OFF
MIC
AUDIO OUT
L RPC
SPDIF
AUDIO IN
DC 24V
HDBT
HDMI
OUTPUTS
6. USB-C
IR EYEIR IN IR OUT TCP/IPRS232
CONTROL
FIRMWARE
Tx Rx24V
DEVICES
21
1
345
26

www.tekvox.com
1201-MV
79033-MV User Manual
3.3 Receiver Front Panel
1. POWER LED: Lights up red when device is powered on
2. HDMI LED: Lights up green when there is an HDMI signal output
3. PC SWITCH: Select whether the Host PC is connected to the switcher or receiver
4. PC: Type-B USB port for Host PC connection. The Host PC can be controlled by the USB
devices (e.g. mouse, keyboard, etc.) which are connected to the USB Type-A ports (DEVICEs).
5. DEVICES (1~3): Three type-A USB ports for USB device connection (e.g. mouse, keyboard,
etc.). These USB devices are used to control the selected Host PC.
6. FW: Micro-USB for firmware upgrade.
3.4 Receiver Rear Panel
1. HDMI OUT: Connects to display device.
2. HDBT IN: Connects to the HDBT output port of switcher via CAT cable. The orange LED lights
up when there is a valid HDBaseT link between the switcher and the receiver. The green LED
lights up when the video contains HDCP content.
3. ETHERNET: RJ45 port for network signal extension. When the TCP/IP port of the switcher is
connected to network, the port will gain network signal via HDBT input.
4. SPDIF OUT: Connects to speaker or amplifier for audio de-embedding.
5. IR IN: Connects to IR receiver for IR pass-through.
6. IR OUT: Connects to IR emitter for IR pass-through.
7. RS232: Connects to a control device (e.g. PC) or a third-party device for RS232 pass-through
control.
HDMI
FW
PC DEVICES321
PC
TX/RX
123456
HDBT IN
HDMI OUT RS232
Tx Rx
SPDIF
OUT IR OUTIR IN
ETHERNET
1234567

www.tekvox.com
1201-MV
79033-MV User Manual
3.5 System Connection
4. Front Panel Control
4.1 Multiview Mode Selection
There are four built-in multiview modes which can be selected via
the front panel buttons.
The factory default multiview mode is quartered window mode,
and the first four input sources correspond with the four output
windows:
Input 1 -> Window A
Input 2 -> Window B
Input 3 -> Window C
Input 4 -> Window D.
The view buttons’LEDs (A~D) turn blue
When switching to two-window (A&B) mode, the corresponding
mode LED will turn blue, and the window A and B LEDs turn blue.
The factory default correspondence between the two input
sources and the two output windows is:
Input 1 -> Window A
Input 2 -> Window B

www.tekvox.com
1201-MV
79033-MV User Manual
4.2 Fullscreen Setting
In multiview mode, press one of the “Window A~D”buttons to
display the corresponding window in single-view mode. The
corresponding input source button LED and window button A LED
will turn blue, and the other window buttons and previous
multiview mode button LEDs will turn off.
4.3 HDMI Output Settings
MIRROR: Press to set the local HDMI output as HDBT loop out,
meaning that the HDMI and HDBT ports will simultaneously output
the same signal source.
BYPASS HDMI 1: Press to set the local HDMI output port to output
the source signal of HDMI input 1
4.4 Audio Control
By default, the HDMI and HDBT output audio follows the video
source in Fullscreen mode. But in the multiview modes, the output
audio will come from the HDMI-1 input. The audio source can be
changed via GUI or RS232 command.
Press the volume knob to select MIC or SOURCE audio. If MIC
audio is selected, then the MIX and MIC mixing audio inputs are
controlled simultaneously.
Rotate the knob to increase or decrease the volume of the
selected audio. Press and hold the knob for at least 3 seconds to
mute the selected audio; rotate the knob to unmute.

www.tekvox.com
1201-MV
79033-MV User Manual
4.5 Video Signal Switching
In Multiview modes
Operation: Input # + Window #
Example: Switch Input 1 to Window B:
Press “Input 1”(The input 1 LED will turn blue, and the A~D LEDs will flash.) Press “Window B”
(The A, C, and D LEDs will go out, and then the input 1 and Window B LEDs will flash three times. The
input 1 LED will then go out, and the A~D LEDs will turn blue.)
In Full Screen mode
1. Manual Switching
Operation: Directly press Input #
If the current status is Input 2 set to full screen Window A, press “Input 3”to switch the HDMI input 3
to Window A. The Input 3 and Window A LEDs will then turn blue.
2. Auto Switching
Press the “AUTO”button to enable or disable auto-switching mode. Note that auto-switching mode
only works while in Fullscreen mode. When in auto mode, the switcher will switch according to the
following rules:
⚫The switcher will switch to the available active inputs with the following priority: Input 1 > Input
2 > Input 3 > Input 4 > Input 5 > Input 6 (USB-C). When the input source and output window are
connected, the corresponding LEDs will turn blue.
⚫New input: The switcher will automatically select a new input once it has been detected.
⚫Reboot: If power is restored to the switcher, it will automatically reconnect to the last-selected
input before being powered off.
⚫In auto mode, the input source also can be switched via the manual switching steps, but doing
so will exit auto-switching mode
⚫When the full screen mode is switched to multiview mode, auto-switching mode will not exit.
4.6 Switching Status
In Multiview mode (Window A, B, C, and D LEDs will turn blue).
Operation: Press and hold Window # button for at least 3 seconds.
Example: Press and hold Window B button for at least 3 seconds (A, C, and D LEDs go out, and then
the corresponding input source LED will turn blue). After 3 seconds, A, B, C, and D LEDs will turn blue.

www.tekvox.com
1201-MV
79033-MV User Manual
5. GUI Control
The switcher can be controlled via TCP/IP. The default IP settings are:
IP Address: 192.168.0.178
Subnet Mask: 255.255.255.0
Type 192.168.0.178 in a web browser, and it will enter the log-in page below:
Username: admin
Password: admin
Type the username and password, then click “Login”to enter the section for video switching.

www.tekvox.com
1201-MV
79033-MV User Manual
5.1 Control Tab
5.1.1 Video Control
⚫Source: Select Window A-D, and then click one of the “1~6”buttons to select the
corresponding input source. Click “Auto”to enable or disable auto switching mode while in
Fullscreen mode.
⚫Select/Full Screen: Window A ~ D buttons for output selection and full screen setting.
⚫HDMI Output: Press the “Mirror”button to set the local HDMI output as HDBT loop out. This
means that the HDMI and HDBT ports will simultaneously output the same signal source.
Press the “Bypass HDMI 1”button to set the local HDMI output port to output the source signal
of HDMI input 1.
⚫Press “Power Off”to enter system standby mode.
Note: The source selectors, Auto, Window A~D, Mirror, and Bypass HDMI 1 buttons are the same as
the front panel buttons. Please see 4.5 Video Signal Switching for more details.

www.tekvox.com
1201-MV
79033-MV User Manual
5.1.2 Display Control
⚫Display: Click “On”or “Off”to simultaneously send RS232 and CEC commands to power the
display device on or off.
⚫Command: Type a command in this box to be sent to control a third-party device, then click
“Send”.
⚫Audio: Click the volume down, volume up, or volume mute icons to send CEC commands to
control the volume of the display device.
⚫Power: Click “Power Off”to enter system standby mode.

www.tekvox.com
1201-MV
79033-MV User Manual
5.1.3 Audio Control
Audio Out & HDMI Out:
⚫Audio In: Enable or disable external audio embedding for HDMI input 1.
⚫Source: Select audio source for outputs.
⚫Source Volume: Use the volume bar, volume up, volume down, and mute buttons for source
audio control.
⚫For Analog Audio Out: Set the delay time for balanced analog audio output.
Mix:
⚫Mix In: Enable or disable mixing audio input.
⚫MIC In: Enable or disable microphone audio input.
⚫MIC Volume: Use the volume bar, volume up, volume down, and mute buttons for Mix and MIC
audio control.
Power: Click “Power Off”to enter system standby mode.

www.tekvox.com
1201-MV
79033-MV User Manual
5.2 Multiview Tab
5.2.1 Pre-Defined Multiview Mode
Up to 12 pre-defined multiview modes can be selected, and then click the gear icon to enter the
interface below to select the input source for each window.