Advantech ADAM-6521 Series User manual

ADAM-6521 Series
Industrial Switches with 4
10/100 Mbps Ethernet Ports
and 1 Fiber Port
User Manual

ADAM-6521 Series User Manual ii
Copyright
The documentation and the software included with this product are copy-
righted 2006 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli-
able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
All other product names or trademarks are properties of their respective
owners.
This Manual Covers the Following Models
• ADAM-6521
• ADAM-6521S
• ADAM-6521/ST
Part No.2003652104 5th Edition
Printed in Taiwan March 2006

iii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war-
ranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

ADAM-6521 Series User Manual iv
CE
This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring. We recommend the
use of shielded cables. This kind of cable is available from Advantech.
Please contact your local supplier for ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful inter-
ference in which case the user will be required to correct the interference
at his own expense.
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Step 2. Contact your distributor, sales representative, or Advantech's
customer service center for technical support if you need addi-
tional assistance. Please have the following information ready
before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, appli-
cation software, etc.)
- A complete description of the problem
- The exact wording of any error messages
Document Feedback
To assist us in making improvements to this manual, we would welcome
comments and constructive criticism. Please send all such - in writing to:
[email protected]

v
Contents
Chapter 1 Overview .......................................................... 2
1.1 Introduction ....................................................................... 2
1.2 Features ............................................................................. 3
1.3 Specifications .................................................................... 4
1.4 Ordering Information ........................................................ 5
Chapter 2 Installation ....................................................... 8
2.1 LED Indicators .................................................................. 8
Table 2.1:LED Indicator Legend ................................... 8
2.2 Dimensions (units:mm) ................................................... 9
Figure 2.1:Bottom .......................................................... 9
Figure 2.2:Top ............................................................... 9
Figure 2.3:Front ............................................................. 9
2.3 Mounting the Module...................................................... 10
2.3.1 Choosing a Mounting Method ..................................... 10
Figure 2.4:Wall Mounting ........................................... 10
Figure 2.5:Attaching DIN Rail Bracket ....................... 11
Figure 2.6:Piggyback Stacking .................................... 11
2.4 Connections..................................................................... 12
2.4.1 Connection to the Devices ........................................... 12
2.4.2 Connection to Other Hubs or Switches ........................ 12
2.4.3 Connection to a Fiber Network .................................... 12
2.4.4 Power Connection ........................................................ 13
Figure 2.7:Power Wiring ............................................. 13

ADAM-6521 Series User Manual vi

2
CHAPTER
1
Overview
This chapter gives an overview of
ADAM-6521 modules.
Sections include:
• Introduction
• Features
• Specifications
• Ordering Information

ADAM-6521 Series User Manual 2
Chapter 1 Overview
1.1 Introduction
The ADAM-6521 series consists of industrial-grade 10/100 Mbps Ether-
net switches with fiber ports that make it possible to expand industrial
networks fast and cost-effectively. In addition to four 10/100 Mbps Ether-
net ports with RJ-45 connector, ADAM-6521 also provide one multi-
mode fiber optic port, while ADAM-6521S provides one single-mode
fiber optic port with a SC-type connector. Using fiber optics, you can pre-
vent noise from interfering with your system and support high-speed (100
Mbps) and long-distance (ADAM-6521: 2km; ADAM-6521/ST: 2km;
ADAM-6521S: 15km) transmissions.
ADAM-6521 modules can accept a input voltage range from +10 to 30
VDC to the terminal block. In addition, the operating temperature is from
-10 to 65° C. The above functions make the ADAM-6521 modules more
stable and reliable, so they are especially suitable for industrial environ-
ments that require Ethernet networking, such as: semiconductor factories,
warehouses, industrial conveyer systems and more.
High-Speed Transmission
ADAM-6521 modules have a switch controller that can automatically
sense transmission speeds (10/100 Mbps). The RJ-45 interface can also
be auto-detected, so MDI or MDI-X is automatically selected and a cross-
over cable is not required. All ports have memory buffers that support the
store-and-forward mechanism. This assures that data is properly transmit-
ted.
Flexible Mounting
Due to its versatility and innovative design, ADAM-6521 modules can be
fixed in three ways: DIN rail, panel and piggyback mounting.
Advanced Protection for Power line
The power line of ADAM-6521 modules supports up to 3000 VDC surge
protection (EFT), which secure equipment against unregulated voltage
and make systems safer and more reliable.

3 Chapter1
Easy Troubleshooting
There are 6 LED indicators supplied that aid troubleshooting for ADAM-
6521 modules. Each port has a pair of LEDs to indicate link status and
port activity. This makes it easy to monitor collisions, link status, power
failure and data reception for on-site diagnostics.
1.2 Features
• Provides 4 x 10/100 Mbps Ethernet ports with RJ-45 connector
• Provides 1 x 100 Mbps multi/single-mode fiber port with SC/ST
connector
• Supports full/half duplex flow control
• Supports MDI/MDI-X auto crossover
• Provides broadcast storm protection
• Embedded with a switch controller, supports auto-negotiation
• Embedded with the memory buffer, supports store-and-forward trans-
mission
• Supports +10 ~ 30 VDC voltage
• Provides surge protection (EFT) 3000 VDC for power line
• Supports ESD protection 4000 VDC for Ethernet Ports
• Provides flexible mountings: DIN rail, stack, panel mounting
• Supports operating temperature: -10 ~ 65° C
• 64 KB of SRAM on chip for frame buffering
• Integrated address Look-Up Engine, supports 1K absolute MAC
addresses

ADAM-6521 Series User Manual 4
1.3 Specifications
Communications
Standard IEEE 802.3, IEEE 802.3u, 802.3x
LAN 10/100Base-T, 100Base-FX
Transmission Distance Ethernet: 100 m
Fiber: ADAM-6521: 2 km
ADAM-6521/ST: 2km
ADAM-6521S: 15 km
Transmission Speed Ethernet: up to 100 Mbps
Fiber: 100 Mbps
Interface
Connectors 4 x RJ-45, 1 x SC type fiber connector
(ADAM-6521, ADAM-6521S) or 1 x ST
type fiber connector (ADAM-6521/ST)
LED Indicators Power, Link (100Base-FX),
100/10M (Ethernet)
Power
Power Connectors 2-pin removable screw terminal
Power Consumption ADAM-6521: Max. 3 W
ADAM-6521/ST: Max. 3 W
ADAM-6521S: Max. 4 W
Power Input Unregulated 10 ~ 30 VDC
Mechanism
Dimensions (W x H x D) 70 x 112 x 27 mm
Enclosure IP30, ABS+PC with solid mounting kits
Mounting DIN 35 rail, stack, wall
Protection
ESD Protection 4,000 VDC (Ethernet)
Surge Protection (EFT) 3000 VDC (Power)